Mitsubishi Electric F700 Instruction Manual page 22

Terminal Terminal
Symbol Name
10E
Frequency
setting power
supply
10
Frequency
2 setting
(voltage)
Frequency
4 setting
(current)
Frequency
1 setting
auxiliary
Frequency
5 setting
common
*1 Set Pr.73, Pr.267, and a voltage/current input switch correctly, then input analog signals in accordance with the settings. Application of voltage with
switch is on (current input specification) or current with switch is off (voltage input specification) could lead to damage to the inverter or analog
circuit of external devices.
(2) Output signals
Terminal Terminal
Symbol Name
A1,
Relay output 1
B1,
(alarm output)
C1
A2,
B2, Relay output 2
C2
Inverter
RUN
running
Up to
SU
frequency
Overload
OL
warning
Instantaneous
IPF
power failure
Frequency
FU
detection
Open collector
SE
output common
Description
When connecting the frequency setting potentiometer at an initial
status, connect it to terminal 10.
Change the input specifications of terminal 2 when connecting it
to terminal 10E. (Refer to Pr. 73 Analog input selection in
Instruction Manual (applied).)
Inputting 0 to 5VDC (or 0 to 10V, 0 to 20mA) provides the
maximum output frequency at 5V (10V, 20mA) and makes input
and output proportional. Use Pr. 73 to switch from among input 0
to 5VDC (initial setting), 0 to 10VDC, and 0 to 20mA.
Set the voltage/current input switch in the ON position to select
current input (0 to 20mA).
*1
Inputting 4 to 20mADC (or 0 to 5V, 0 to 10V) provides the
maximum output frequency at 20mA (5V, 10V) makes input and
output proportional. This input signal is valid only when the AU
signal is on (terminal 2 input is invalid). Use Pr. 267 to switch from
among input 4 to 20mA (initial setting), 0 to 5VDC, and 0 to
10VDC. Set the voltage/current input switch in the OFF position
to select voltage input (0 to 5V/0 to 10V).
(Refer to Instruction Manual (applied).)
Inputting 0 to ±5 VDC or 0 to ±10VDC adds this signal to terminal
2 or 4 frequency setting signal. Use Pr.73 to switch between the
input 0 to ±5VDC and 0 to ±10VDC (initial setting).
Common terminal for frequency setting signal (terminal 2, 1 or 4)
and analog output terminal AM and CA. Do not earth.
Description
1 changeover contact output indicates that the inverter
protective function has activated and the output stopped.
Abnormal: No conduction across B-C (Across A-C Continuity),
Normal: Across B-C Continuity (No conduction across A-C)
1 changeover contact output
Switched low when the inverter output frequency is equal to or higher
than the starting frequency (initial value 0.5Hz). Switched high during
stop or DC injection brake operation.
Switched low when the output frequency
reaches within the range of ±10% (initial
value) of the set frequency. Switched high
during acceleration/deceleration and at a
stop.
*2
Switched low when stall prevention is
activated by the stall prevention
function. Switched high when stall
prevention is cancelled.
*2
Switched low when an instantaneous
power failure and under voltage
protections are activated.
*2
Switched low when the inverter output
frequency is equal to or higher than the
preset detected frequency and high
when less than the preset detected
frequency.
*2
Common terminal for terminals RUN, SU, OL, IPF, FU
*1
*2
Alarm code (4bit)
output
Wiring
Rated
Refer to
Specifications
10VDC Instruction
Permissible load Manual
current 10mA (applied)
5VDC
Permissible load 38, 46
current 10mA
Voltage input:
Input resistance
38, 46
10kΩ ± 1kΩ
Maximum
permissible
voltage 20VDC
Current input:
Input resistance
245Ω ± 5Ω
40, 48
Maximum
permissible
current 30mA
Input resistance
10kΩ ± 1kΩ Instruction
Maximum Manual
permissible voltage (applied)
± 20VDC
--- ------ ------ ----- -- ----
Rated
Refer to
Specifications
Instruction
Contact capacity:
Manual
230VAC 0.3A
(applied)
(Power
factor=0.4)
Instruction
30VDC 0.3A
Manual
(applied)
Instruction
Manual
(applied)
Instruction
Manual
(applied)
Permissible load
24VDC 0.1A
Instruction
(A voltage drop is
Manual
3.4V maximum
(applied)
when the signal is
on.)
Instruction
Manual
(applied)
Instruction
Manual
(applied)
---- ------- ------ --- --- --
17
2