Maintenance - Craftsman 315.SS630 Operator's Manual

WaRninG:
When servicing, use only identical
replacement parts. Use of any other parts may
create a hazard or cause product damage.
WaRninG:
Always wear eye protection with side
shields marked to comply with ANSI Z87.1. Failure
to do so could result in fluids entering your eyes
resulting in possible serious injury.
MainTEnanCE pROCEDURES
nOTE: Always remove the battery pack from the unit
before attempting a service operation.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
WaRninG:
Do not at any time let brake fluids,
gasoline, penetrating oils, etc., come in contact with
plastic parts. Chemicals can damage, weaken, or
destroy plastic which may result in serious personal
injury.
CLEaninG ThE SpRaYER FOR STORaGE
See Figure 8, page ii.
When you've finished your project and are ready to store the
sprayer, a thorough cleaning and lubrication is recommended.
 Remove the battery pack from the sprayer.
 Remove the paint container.
 If you haven't already done so, return any unused paint
or stain to its original container.
 Fill the paint container with lukewarm water (following
the use of latex products) or any non-flammable paint
thinner (following the use of oil-based products).
 Reinstall the paint container.
 Install the battery pack in the sprayer.
 Spray the solution onto a piece of cardboard or other
scrap material. Continue spraying until all the solution
is used.
 Remove the battery pack from the sprayer.
 Remove the paint container.
 Remove the suction tube and filter.
 Remove the installed spray tip by turning it counter-
clockwise.
 Remove the atomizer valve assembly.
 Remove the locking nut by turning it counterclockwise.
 Slide the pump housing assembly/container lid forward
off the sprayer.
 Pull the piston and spring off the pump housing.

MainTEnanCE

 Using the cleaning brush provided and the solution
determined by the last type of paint or stain sprayed,
clean all of the above parts thoroughly.
nOTE: Make sure to scrub thoroughly inside the pump
housing opening so that no paint or stain material is left
behind.
 Clean the vent hole in the pump housing using a
straightened paper clip.
To reassemble:
 Place a line of lubricant on the piston.
 Slide the spring back onto the piston.
 Insert the piston and spring assembly inside the back
of the pump housing.
 Replace the pump housing assembly/container lid onto
the sprayer.
 Replace the locking nut on the motor housing by push-
ing in while rotating clockwise to secure.
 Insert the atomizer valve assembly into the pump hous-
ing front opening.
 Replace the spray tip and rotate clockwise to secure.
 Reinstall the suction tube and filter.
 Reinstall the paint container.
 The sprayer is now ready to be stored.
REpLaCinG aTOMizER VaLVE aSSEMBLY
See Figure 10, page ii.
The atomizer valve causes the paint or stain material to
spin as it comes out of the sprayer. After 7 to 10 gallons of
paint or stain, the atomizer valve may no longer produce a
good spray pattern and may need to be replaced.
To replace:
 Remove the battery pack from the sprayer.
 Rotate the spray tip counterclockwise and remove.
 Install the new atomizer valve assembly
 Replace the spray tip and rotate clockwise to secure.
BaTTERY paCK REMOVaL anD
pREpaRaTiOn FOR RECYCLinG
WaRninG:
pack's terminals with heavy-duty adhesive tape.
Do not attempt to destroy or disassemble battery
pack or remove any of its components. Lithium-ion
and nickel-cadmium batteries must be recycled
or disposed of properly. Also, never touch both
terminals with metal objects and/or body parts as
short circuit may result. Keep away from children.
Failure to comply with these warnings could result in
fire and/or serious injury.
10 - English
Upon removal, cover the battery