• Operation • Maintenance • Troubleshooting • Repair Parts • Español CAUTION: Read the Safety Guidelines and All Instructions Carefully Before Operating. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. Visit our Craftsman website: www.sears.com/craftsman D25867 Rev. 0 2/5/02...
SAFETY GUIDELINES - DEFINITIONS This manual contains information that is important for you to know and understand. This information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the symbols below. Please read the manual and pay attention to these sections.
HAZARD WHAT CAN HAPPEN HOW TO PREVENT IT The solvents 1,1,1-Trichloroethane Read the label or data sheet for RISK OF Methylene Chloride the material you intend to spray. EXPLOSION - chemically react with the alumi- INCOMPATIBLE num used in most spray equip- Never use any type of MATERIALS ment, and this gun and cup, to...
GENERAL INFORMATION Before disassembly or removal of any part of gun or attached components, shut off compressor, release pressure by depressing trigger, and disconnect power source. NEVER assume system pressure is zero! TO AVOID CREATING AN EXPLOSIVE ATMOSPHERE, WORK ONLY IN WELL-VENTILATED AREAS. USE OF A NIOSH APPROVED FACE MASK IS RECOMMENDED TO PREVENT INHALATION OF TOXIC MATERIAL.
Page 5
TO USE Mix material according to the manufacturer’s instructions. Mixture should be smooth and easily pourable. Lumps or foreign particles should be removed by straining through a suitable paint filter. NOTE: If not using the siphon feed setting, see “Remote Pressure Feed” paragraphs. Remove the material cup (e) from lid/gun assembly.
Page 6
Convert to Remote Pressure Feed: If the material to be sprayed is too heavy for siphon feed or fast application is desired, convert to the pressure feed setting. Remove the material cup (e) from lid/gun assembly. NOTE: Slide release lever (f) to the right, rotate lid, and remove material cup (e).
MAINTENANCE Always exercise extreme care when using any solvent or thinner. Never clean gun near fire, flame, or any source of heat or sparks. Properly dispose of used cleaning materials. DO NOT soak entire spray gun in solvent or thinner for a long period of time as this will destroy lubricants and possibly make motion uneven.
TROUBLESHOOTING Likely Cause Suggested Remedy Defective Pattern Dried material Soak side-ports in is clogging thinner to clean clog. side-port “A” DO NOT poke any and causing opening with hard side-port “B” to objects. blow spray towards the clogged side Remove air nozzle. Dried material at Wipe off fluid tip using a fluid nozzle “C”...
NORMAS DE SEGURIDAD - DEFINICIONES Este manual contiene información que resulta importante para que usted conozca y comprenda. Esta información se relaciona con la protección de SU SEGURIDAD y LA PREVENCIÓN DE PROBLEMAS A SU EQUIPO. Para ayudarlo a identificar esta información hemos utilizado los símbolos que se indican más abajo.
PELIGRO QUÉ PUEDE OCURRIR CÓMO PREVENIRLO Solventes del tipo 1, 1, 1 - Lea la etiqueta o la hoja de RIESGO DE Tricloroetano Cloruro especificaciones del material EXPLOSIÓN - metileno, pueden reaccionar que usted intenta rociar. MATERIALES químicamente con el aluminio 1.Jamás use tipo alguno de INCOMPATIBLES utilizado en la mayoría de los...
INFORMACIÓN GENERAL Antes del desarmado o remoción de cualquier parte, del pistola o cualquiera de sus componentes, apague el compresor, libere su presión apretando el gatillo, y desconecte el suministro de corriente eléctrica. ¡JAMÁS asuma que la presión del sistema es cero! PARA EVITAR LA CREACIÓN DE UN ATMÓSFERA EXPLOSIVA, TRABAJE SOLAMENTE EN ÁREAS BIEN VENTILADAS.
Page 12
CÓMO USAR: Mezcle el material de acuerdo a las instrucciones del fabricante. La mezcla debe ser ligera y fácilmente fluida. Grumos o partículas extrañas deberán extraerse a través de un filtro adecuado para pintura. NOTA: Si no se utilizan las características de alimentación por sifón, vea los párrafos de "Alimentación remota a presión".
Page 13
JAMÁS apunte la pistola rociadora a sí mismo o a persona alguna. Una descarga accidental de material podría determinar serias lesiones. NOTA: Si la pistola pulveriza demasiado rápido, desminuya la presión de salida del aire y del fluido. Si es demasiado baja, incremente la presión. Gire la perilla de control de fluido (b) en sentido antihorario para incrementar, o en sentido horario para disminuir la salida del aire.
MANTENIMIENTO Ejerza siempre extremo cuidado al utilizar cualquier solvente o diluyente. Jamás limpie la pistola cerca del fuego, llama o cualquier fuente de calor o chispas. Deseche adecuadamente los materiales utilizados para limpieza. NO embeba la pistola rociadora completamente en solvente o diluyente durante un largo periodo de tiempo, dado que ello destruirá...
DIAGNÓSTICO DE PROBLEMAS Patrón defectuoso Causa probable Solución sugerida Material seco que Embeba en diluyente los esta obturando el laterales de los portales portal del lado "A", para limpiar la siendo la causa de obturación. NO que el portal "B" aguijonee abertura atomice hacia el alguna con objetos...
Page 18
Get it fixed, at your home or ours! For repair of major brand appliances in your own home… no matter who made it, no matter who sold it! 1-800-4-MY-HOME Anytime, day or night (1-800-469-4663) www.sears.com To bring in products such as vacuums, lawn equipment and electronics for repair, call for the location of your nearest Sears Parts &...