Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Reebok edge series
Summary of Contents for Reebok edge series
- Page 3 Dear Customer, We are pleased, that you have chosen a Reebok Fitness Equipment. This quality product has been designed for in-home use and has been tested and certified according to the European Norm EN 957-1/5. Please carefully read the instructions prior to assembly and first use and be sure to keep the instructions for reference and maintenance.
- Page 4 Technical support: tel: 0044 (0) 1908 793030 e-mail: techsupport@rfeinternational.com Advice The owner’s manual is only for the customer reference. Reebok can not guarantee for mistakes occurring due to translation or change in technical specification of the product.
- Page 5 Product-Preparation: Follow the steps of the assembly instruction carefully. • Product-Preparation:Only use suitable tools for assembly and ask for assistance if necessary. • Product-Preparation: Only use original Reebok parts as delivered (see checklist). • Use-Preparation: Tighten all adjustable parts to prevent sudden movement while training.
- Page 6 For this reason, worn or damaged parts should be replaced immediately and the equipment taken out of use until this has been done. • Product-Maintenance: Only use original Reebok spare parts. • Product-Maintenance: Do not under any circumstances carry out electrical repairs or alterations yourself.
- Page 7 Check List M4x15mmM8x65mm M8x20mm 5 mm...
- Page 8 Assembly instruction PUSH...
- Page 9 215-2x 537-2x 214-2x 215-2x 537-2x 302-2x 110-1x 215-2x 537-2x 302-2x...
- Page 10 110-2x...
- Page 11 Power Transport...
- Page 12 Correct Use Proper Ergonomic Positioning: Please refer to the diagram to the left as indication of the proper training position. To obtain this, please adjust the handlebar and saddle position to your body height. Mounting: When getting on/off the equipment be sure to place your weight only on the pedals when in the lower-most position.
-
Page 13: Exploded View
Exploded view 513 514 525 509... - Page 14 Spare Part List Part No. Part name Quantity Overlay Console housing-Upper Battery Cover Handle Bar Cover-Rear Handle Bar Cover-Front Hand Pulse sensor Wire Speed Sensor Wire- upper Console housing –lower M4X15 Screw PC Board Console –upper Handle Bar Tube Hand Pulse Sensor-Upper Hand Pulse Sensor Cover-lower Handle Bar Foam Grip Hand pulse sensor Wire –lower...
- Page 15 Saddle Main Frame M5X14 Screw Upright lower section insert Saddle post bottom holder M8 nut Main Chain Cover- Left Seat Post Plastic Holder Chain Cover-Front Main Chain Cover -right Plastic Insert Pedal-Left Crank cap M10X1.25 Nut Crank-Left Crank-Right Pedal-Right 6004 Bearing M20 Nut Ø22 Washer Driving Belt pulley...
- Page 16 M10 Nut Flywheel D-Shaped Holder One way bearing 6003Z Bearing M6 Nut Ø8 Spring-Washer Ø10 washer D0.8 X 20 Spring Magnet bracket M10X73 Magnet bracket axle M6X40 bolt Motor Ø6 washer...
- Page 17 COMPUTER INSTRUCTION Functions and Features: 1. Start: Allows you to start the computer just press the START key without selecting a program. TIME automatically begins to count up from zero. Use the UP and DOWN keys to adjust the resistance. 2.
- Page 18 1. START/STOP key: a. During the exercise mode, press the key to STOP exercise. b. During the stop mode, press the key to START exercise. c. Press this key can allow you to quickly start the computer without selecting a program. For Manual workout only. Time automatically begins to count up from zero 2.
- Page 19 Preset Program: Rolling, Valley, Fat Burn, Ramp, and Mountain Program PROGRAM 2 to PROGRAM 6 is the preset programs. Users can exercise with different level of loading in different intervals as the profiles show. Users may exercise in any desirous of resistance level (Adjusting by UP/DOWN key during the workout) with a period of time or a number of calories or a certain distance.
- Page 20 your exercise TIME. Press ENTER key to confirm your desired workout TIME. 4. The DISTANCE will flash and you can press UP or DOWN keys to setting your target DISTANCE. Press ENTER key to confirm your desired workout DISTANCE. 5. The CAL will flash and you can press UP or DOWN keys to setting your exercise CALORIES.
- Page 21 seconds then the gear motor’s driver will be cut off immediately and show the E1 on the LCD display. All the other digital and function mark are blank, and the output signals are cut off also. E2 (ERROR 2): When the monitor read the memory data, if the I.D. code is not correct or the memory IC damages then the monitor will show E2 immediately at power on.
Need help?
Do you have a question about the edge series and is the answer not in the manual?
Questions and answers
Hi, I lost the power supply for my edge series cross trainer. What is the appropriate voltage for it. Many thanks.
The appropriate voltage for the power supply of the Reebok Edge Series cross trainer is 220V – 230V / 50Hz.
This answer is automatically generated
How do I clear error messages
To clear error messages on the Reebok Edge Series, follow these steps:
1. Identify the Error – If an error message appears, check the display to determine the specific error code.
2. Wait for Auto-Check – The system will automatically check for errors. If the issue persists, Error 1 (E1) will be displayed.
3. Restart the Machine – Turn off the equipment and unplug it from the power source. Wait a few seconds, then plug it back in and turn it on.
4. Check Connections – Ensure all cables and connections are secure and properly attached.
5. Adjust Resistance – If the error occurs during a workout, try adjusting the resistance level using the UP/DOWN keys.
6. Contact Technical Support – If the issue is not resolved, contact Reebok technical support at 0044 (0) 1908 793030 or techsupport@rfeinternational.com for further assistance.
This answer is automatically generated