Related Manuals for Brivis L26
Summary of Contents for Brivis L26
- Page 1 C O O L I N G Owner’s Manual PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USE company...
-
Page 2: Table Of Contents
Operating your evaporative cooler ....3 Operating Your Manual Wall Control Start up Brivis Customer Care Program ....13-14 Shut down Cooler Service & Maintenance... -
Page 3: Introduction
To be at their most efficient they, like most things, need a little care. So, to ensure that every Brivis unit is always in perfect condition, we have established the Brivis Care Program for our valued customers. -
Page 4: Safety Warnings
Openings Required Table 1. Opening required for each model. Number of average Highest Lowest Model size windows & doors Setting Setting (suggestions only) Brivis Brivis Brivis Brivis Contour Promina Advance AD Series Series Series Two sliding windows or F26D 1.5 m... -
Page 5: Operating Your Evaporative Cooler
Brivis Advance, Brivis Promina and Brivis Contour models have an additional pre-programmed tank wash cycle (flush). This washes the tank with clean water at the end of use. At the same time Brivis Contour models will also close the motorised ServoSeal damper, which seals the ducting, reducing drafts. The ServoSeal and flush will occur approx 1 hour after the unit has been turned off. -
Page 6: Operating Your Brivis Networker Wall Control
The Mode Key If a Brivis Heater and Cooler are connected to the Brivis Networker, this key allows you to switch between them. When an appliance is selected the mode of the appliance will appear at the bottom of the screen e.g. ‘Evap Cooler’. -
Page 7: Automatic Pre-Wet
During the Pre-Wet the message “Pre-Wetting cooler pads - Please Wait!” will scroll across the top of the display. Automatic Operation In Auto mode the Brivis Networker automatically turns the pump ON or OFF as required and varies the fan speed to maintain your selected “comfort level.” On/Off... -
Page 8: Manual Operation
Manual operation enables you to control the fan, its speed, and the pump manually. To run the Cooler in Manual mode, just follow these steps: • Turn the Brivis Networker on using the ON/OFF button. • Press the Auto key until “MANUAL” appears on the screen. -
Page 9: Setting The Time & Day
Once Timer settings are made you can review or cancel them in a number of ways: • The words On Time or Off Time will remain on the screen to show that the Brivis Networker is now holding your pre-set ON or OFF time. -
Page 10: Checking Your Timer Settings
Brivis Service. If the Cooler is still operating but the Brivis Networker is showing an error message try pushing the Reset Key 4 to clear the fault. If the fault persists contact Brivis Service. If the Cooler is not operating and any other error message appears, contact Brivis Service. -
Page 11: Setting The Pin
PIN. On the third failed attempt the message “Invalid PIN entered!” will be displayed. At this point the Brivis Networker will abort the PIN entry screen, and return to its original state. -
Page 12: Dual Brivis Networker Operation
The benefit of having two controllers is the convenience of making adjustments to the Cooler settings. If an adjustment is made on one of the Brivis Networkers it is immediately reflected on the other Brivis Networker. When locking one of the Brivis Networkers the other one will also be locked, and the system can be unlocked at either Brivis Networker. -
Page 13: Operating Your Programmable Wall Control
• Push the UP and DOWN keys to select the comfort level you require. The lower the number, the cooler the setting; the higher the number, the warmer the setting. Benefits of using Brivis coolers in AUTO mode in preference to Manual mode •... -
Page 14: Manual Operation
Manual Operation Manual operation requires you to manually control the fan, its speed, and the pump. Getting started Begin by pressing the ON/OFF key to turn the Cooler on. For Manual operation the AUTO light must not be illuminated. • Push the MODE key to cycle through the cooler’s operating modes. Fan and Pump This is indicated by the illuminated Fan and Pump lights. -
Page 15: Brivis Customer Care Program
To be at their most effecient they, like most things, need a little care. So to ensure that every Brivis unit is always in perfect condition we have established the Brivis Care Program for our valued customers. -
Page 16: Troubleshooting Continued
Serial Number: Install Date: Installed by: Installer Contact: Service Records To arrange a visit from one of our certified technicians please contact the Brivis Service department on 1300 BRIVIS Service Provider: Contact Number: Service Year 2 Service Date: Service Year 4... -
Page 17: Warranty And Maintenance Registration
An extra charge may apply if Brivis is required to allocate two service personnel to enable compliance with safety regulations. -
Page 18: Cooler Customer Questionnaire
Delivery Address: 61 Malcolm Rd BRAESIDE VIC 3195 Brivis Climate Systems Reply Paid 85321 BRAESIDE VIC 3195 Cooler Customer Questionnaire Please tick the appropriate box. Number. _______________________ • Have you been given a certificate of compliance? Yes • What type of home do you live in? -
Page 19: Frequently Asked Questions
Q. How often should the cooler be serviced? Brivis recommend the cooler is serviced every 2 years at a minimum to ensure it operates at peak efficiency. Please Note: Due to environmental conditions the cooler may need to be serviced every year. -
Page 20: Frequently Asked Questions
This means you will see the unit dump the water out of the overflow pipe. Brivis Contour models will not dump any water during operation as they are fitted with an AquaSave which operates to keep the water clean. -
Page 21: Terms Of Warranty
Terms of Warranty – Australia and New Zealand Brivis Climate Systems Pty. Ltd. ABN 64 096 079 088, AU24752 61 Malcolm Rd, Braeside, VIC 3195. 1. Definitions The terms listed below shall have the following meanings: 1. “Authorised Service Representative” means an independent service contractor authorised by Brivis or Brivis service personnel. -
Page 22: Conditions Of The Warranty
Service or Owner’s Manual; b) complies with clause 7 below (titled "Purchaser's Responsibilities"); c) notifies Brivis within 30 days of a defect developing, that a claim is being made under this Warranty; and d) provides, in support of the claim made under this Warranty, a Proof of Purchase. -
Page 23: Travel, Transport & Access Costs
Brivis considers appropriate, it will authorise the Purchaser in writing to pay for the relevant freight charges, in-transitinsurance expenses or travelling costs and then, upon provision by the Purchaser to Brivis of a tax invoice showing those costshave been incurred, reimburse the Purchaser for such costs which are within the terms of the authorisation. - Page 24 Copyright – Brivis Climate Systems Pty Ltd All rights reserved. No part of these documents may be used in any way or form without prior written consent from Brivis Climate Systems Pty Ltd. Part Number: B022832O September 2015...
Need help?
Do you have a question about the L26 and is the answer not in the manual?
Questions and answers