Beep Strap; Microphone/Speaker Sensitivity Adjustment (Speakerphones Only); Busy Override And Camp-On Ring Tone Over Handset Option - Toshiba Strata DK24 Installation And Maintenance Manual

INSTALLATION-TELEPHONE
SECTION 400-096-207
SEPTEMBER 1992
3) Reinstall the telephone base, and secure it
with its four captive screws.

3.50 Beep Strap

3.51 A "beep" sounds whenever a dialpad button
or feature button is pressed on a digital telephone.
To eliminate this beep follow the procedure below:
1) Loosen the four captive screws securing the
telephone base (Figure 7-1), and remove the
base.
NOTE:
Although Figure 7-1 specifically illustrates
how to remove an electronic telephone base,
it also applies to digital telephones.
2A) For 2000-series digital telephones, refer to
Figures 7-7 or 7-8, and cut the BEEP strap.
2B) For 1000-series digital telephones, refer to
Figure 7-9, and cut the BEEP strap.
3) Reinstall the telephone base, and secure it
with its four captive screws.
3.60 Microphone/Speaker Sensitivity Adjust-
ment (Speakerphones Only)
3.61 High ambient noise levels may cause the
speaker on some digital telephone speakerphone
models to cut off frequently. To prevent this for the
1000-series digital telephone models, perform the
following procedure to make the telephones less
sensitive to the noise: (The 2000-series Tele-
phones are adjusted per the instructions in the
Note after the procedure.)
1) Loosen the four captive screws securing the
1000-series Digital Telephone speakerphone
base (Figure 7-1), and remove the base.
NOTE:
Although Figure 7-1 specifically illustrates
how to remove an electronic telephone base,
it also applies to digital telephones.
2) For the 1000-series speakerphone model
(DKT1020-SD), refer to Figure 7-9, and lo-
cate the ROOM NOISE switch. Push the
switch carefully to the H (high) position (for
low sensitivity) when there is high background
noise in the area surrounding the telephone.
3) Reinstall the telephone base, and secure it
with its four captive screws.
NOTES:
1. To make the 2000-series Digital Tele-
phone speakerphone models less sensi-
tive to loud surrounding noise, hold down
Mic button, then press the up
The less-sensitive level will be set after
the third flash of the Mic LED. To reset the
sensitivity back to the normal level, hold
down the
Mic
button. The normal level will be set
Vol
after the third flash of the Mic LED.
2. On 2000-series Digital Telephone speak-
erphone models that are set for low sen-
sitivity, the Mic LED will flash at the in-use
rate when using the speakerphone. When
set to normal sensitivity, the Mic LED will
be on steady when using the speaker-
phone.
3.70 Busy Override and Camp-on Ring Tone
over Handset Option
3.71 The Busy Override and Camp-on Ring tones
can be sent over the telephone handset or head-
set, in addition to the speaker, with 2000-series
digital telephones. The tones only sound over the
speaker with 1000-series Digital Telephones. Per-
form the following procedure to have these tones
sent over the handset of the DKT2010-H model:
(For the DKT2010-SD, the DKT2020-S, and the
DKT2020-SD models, see the Note following the
procedure.)
1) Loosen the four captive screws securing the
telephone base (Figure 7-1), and remove the
base.
NOTE:
Although Figure 7-1 specifically illustrates
how to remove an electronic telephone base,
it also applies to digital telephones.
7-10
Vol button.
button , then press the down