Related Manuals for DeWalt DPD3100
Summary of Contents for DeWalt DPD3100
- Page 1 If you have questions or comments, contact us. 1-800-4-D WALT • www.dewalt.com INSTRUCTION MANUAL DPD3100 Pressure Washer...
-
Page 2: Pump Specifications
FIG. 1 DPD3100 Pressure Washer Panel assembly Starter grip Nozzle holder Engine Professional Spray gun Choke control Side Handle Throttle control lever Quick-connect Fuel valve lever spray wand Gas cap Frame Handle assembly Engine dipstick/oil plug High-pressure hose Engine switch... -
Page 3: Specifications
Specifications MoDeL WeIGht heIGht WIDth LenGth Max* aVeraGe GPM Max* aVeraGe enGIne oPeratInG oPeratInG DPD3100 83.6 lbs 26.5" 23" 40" 3100 2780 WALT (10.6 L/min) (10.3 L/min) (21373 kPa) (19167 kPa) 196 cc OHV, 5.5 Net HP, 6.5 Gross HP **... - Page 4 7. Do not overreach or stand on unstable support. Keep good footing and balance at all times. 8. Follow the maintenance instructions specified in the manual. DANGER: RISk Of INjECTION OR SEvERE INjURy. kEEP DANGER: RISk Of ExPlOSION OR fIRE ClEAR Of NOzzlE.
- Page 5 • Muffler exhaust heat can • Always keep pressure washer DANGER: RISk TO BREAThING (ASPhyxIATION) CONTINUED a min i mum of 4' (1.2 m) away damage paint ed sur fac es, • Some cleaning fluids • Use only cleaning fluids melt any material sen si tive from sur fac es (such as to heat (such as siding,...
- Page 6 DANGER: RISk Of flUID INjECTION AND lACERATION CONTINUED • Your pressure washer • Direct spray away from self DANGER: RISk Of INjURy fROm SPRAy operates at fluid pressures and others. What can happen how to prevent it and velocities high enough to •...
- Page 7 • If proper starting procedure • If engine does not start after is not followed, engine can two pulls, squeeze trigger kickback causing serious of gun to relieve pump DANGER: RISk Of UNSAfE OPERATION hand and arm injury. pressure. Pull starter cord slowly until resistance is felt.
- Page 8 DANGER: RISk Of INjURy OR PROP ER Ty DAmAGE WhEN WARNING: RISk Of BURSTING TRANSPORTING OR STORING What can happen how to prevent it What can happen how to prevent it • Over inflation of tires could • Use a tire pressure gauge to •...
- Page 9 WARNING: RISk Of ElEC TRI CAl ShOCk WARNING: RISk Of hOT SURfACES What can happen how to prevent it What can happen how to prevent it • Spray directed at electrical • Unplug any electrically • Contact with hot surfaces, •...
-
Page 10: Installation
InSTALLATIon note: The high pressure pump is maintenance free and requires no oil, if there is a problem with the pump contact a D WALT factory Pressure Washer Assembly (Fig. 1) service center, a D WALT authorized service center or other qualified 1. -
Page 11: Chemicals And Cleaning Solvents
chanGInG nozzLes on sPray WanD nozzle color spray Pattern uses surfaces* DANGER: Risk of fluid injection. Do not direct discharge stream 0˚ powerful metal or toward persons, unprotected skin, eyes or any pets or animals. pinpoint for concrete; Serious injury will occur. very intense DO NOT use WARNING: Flying objects could cause risk of serious injury. - Page 12 • 3. Install low-pressure (black) nozzle into quick connect fitting of spray DO NOT let hoses come in contact with very hot engine wand, refer to spray Wand nozzles. note: Chemicals and soaps muffler during or immediately after use of your pressure will not siphon if the black soap nozzle is not installed on the washer.
-
Page 13: Shutting Down
4. Verify the filter screen (U) is in water inlet of pump. WARNING: Risk of unsafe operation. Pull starter grip slowly The cone side faces out. until resistance is felt. Then pull starter grip (I) rapidly to avoid kickback and prevent hand or arm injury. 5. -
Page 14: Maintenance
Pump CAUTION: Risk of property damage Failure to do so could cause damage to the pump. The high pressure pump is maintenance free and requires no oil, if 2. Place the engine ON/OFF switch (H) to the OFF Position. there is a problem with the pump contact a D WALT factory service 3. -
Page 15: Pressure Washer
1. Remove the filter screen (U) by grasping the 1. Obtain a funnel, 6 oz. (170 mL) of RV antifreeze and 16–36" end and removing it from water inlet of (40–91cm) of garden hose with a male hose connector attached pump. -
Page 16: Service Information
For further details of warranty coverage and warranty repair informa- vided with this pressure washer as measured from the nozzle end tion, visit www.dewalt.com and click on Service and Support or call of the lance to the gun trigger. 1-800-4-D WALT (1-800-433-9258). - Page 17 Glossary Free WarnInG LaBeL rePLaceMent: If your warning labels (next page) become illegible or are missing, call 1-800-4-D WALT Bypass mode: Allows water to re-circulate within pump when the for a free replacement. gun trigger is not pulled. chemical hose: Feeds cleaning agents into the pump to mix with the water.
-
Page 18: Troubleshooting Guide
Troubleshooting Guide This section provides a list of the more frequently encountered malfunctions, their causes and corrective actions. The operator or maintenance personnel can perform some corrective actions, and others may require the assistance of a qualified D WALT technician or your dealer. Problem code Engine will not start ......................1, 2, 3, 4, 5, 6, 7, 8, 29... - Page 19 (Troubleshooting codes cont.) coDe PossIBLe cause PossIBLe soLutIon Low water supply. Water supply must be at least 5 GPM @ 20 PSI (138 kPa). Leak at high-pressure hose fitting. Repair leak. Apply sealant tape if necessary. Nozzle obstructed. See nozzle cleaning under Maintenance. Water filter screen clogged.
- Page 20 (Troubleshooting codes cont.) coDe PossIBLe cause PossIBLe soLutIon Loose hose connection. Tighten. Piston packings worn. Have replaced by authorized service center. Pump head or tubes damaged from freezing. Have replaced by authorized service center. Air filter filled with oil. Clean air filter element. Refer to engine instruction manual for correct procedure.