Telis 1 RTS Contents 1. Brief introduction to the Telis 1 RTS remote control 1.1 What is the Telis 1 RTS for? 1.2 A few definitions 2. Safety - Important information 2.1 Installation and commissioning 2.2 Operating 2.3 Environment 3. Content of the kit and tools required 3.1 List of parts...
(address on the back cover of these instructions). 1.1 What is the Telis 1 RTS for? The Telis 1 RTS is a wireless radio remote control compatible only with products fitted with Radio Technology Somfy (RTS): The Telis 1 RTS is used: •...
Avoid moving the roller shutter/awning if ice has formed in it, unless the motor is fitted with anti-freeze protection. Do not leave the Telis 1 RTS behind a window in full sunlight as it cannot withstand temperatures greater than 60°C.
3. Content of the kit and tools required 3.1 List of parts Before starting installation and commissioning of the Telis 1 RTS, check that all parts listed in the table below are present in the correct quantity (Q): Components...
5.1 Identifying the original control point 5.1.1 Installation recommendations To add a Telis 1 RTS, use the control point linked to the product which controls only this product: pressing the Down or Up button only causes movement of the product to which the new Telis 1 RTS must be connected.
Page 7
5.1.2 Original control points Find the original control point in the list below and refer to the paragraph given to add the new Telis 1 RTS: 1) Control point fixed to the wall with a single button, called a One-touch point, see paragraph 5.2;...
Page 9
3 beeps): the programming function of your RTS enabled products is activated for approximately 2 minutes. Take the new Telis 1 RTS and turn it over. Press the PROG button (E) on the new Telis 1 RTS briefly with the tip of...
Page 10
3 beeps): the programming function of your RTS enabled products is activated for approximately 2 minutes. Take the new Telis 1 RTS and turn it over. Press the PROG button (E) on the new Telis 1 RTS briefly with the tip of...
Page 11
Take the new Telis 1 RTS and turn it over to access the PROG button (E). Press the PROG button (E) on the new Telis 1 RTS with the tip of a pencil until the product moves briefly (or a series of 3 beeps is emitted): the program-...
Page 12
Take the new Telis 1 RTS and turn it over to access the PROG button (E). Press the PROG button (E) on the new Telis 1 RTS with the tip of a pencil until the product moves briefly (or a series of 3 beeps is emitted): the program-...
Caution! If after removing the front cover, no PROG button is found, this means that the control point is not compatible: the Telis 1 RTS cannot be linked to the product. 5.3.2 Adding the Telis 1 RTS Switch the mains power supply back on or reconnect the battery to the motor.
Page 14
Take the new Telis 1 RTS and turn it over to access the PROG button (E). Press the PROG button (E) on the new Telis 1 RTS with the tip of a pencil until the product moves briefly (or a series of 3 beeps is emitted): the program-...
Page 16
3 beeps): the programming function of your RTS enabled products is activated for approximately 2 minutes. Take the new Telis 1 RTS and turn it over. Press the PROG button (E) on the new Telis 1 RTS briefly with the tip of...
Take the new Telis 1 RTS and turn it over to access the PROG button (E). Press the PROG button (E) on the Telis 1 RTS with the tip of a pencil until the product moves briefly (or a series of 3 beeps is emitted): the program-...
Page 18
RTS enabled products is activated for approximately 2 minutes. Take the new Telis 1 RTS and turn it over. Press the PROG button (E) on the new Telis 1 RTS briefly with the tip of...
Page 19
Telis 1 RTS Press the PROG button (E) on the new Telis 1 RTS with the tip of a pencil until the product moves briefly (or a series of 3 beeps is emitted): the program- ming function of your RTS enabled products is activated for approximately 2 minutes.
Telis 1 RTS 5.6 Telis 1 RTS Telis Soliris RTS remote controls The Telis 1 RTS has 1 indicator light (5a) and the Telis Soliris RTS has 2 indicator lights (5b). If the original remote control has more than 2 indicator lights, refer to the section "Telis 4 RTS/Telis 4 Soliris RTS remote...
Page 21
Take the new Telis 1 RTS and turn it over to access the PROG button (E). Press the PROG button (E) on the new Telis 1 RTS with the tip of a pencil until the product moves briefly (or a series of 3 beeps is emitted): the program-...
RTS enabled products is activated for approximately 2 minutes. Take the new Telis 1 RTS and turn it over. Press the PROG button (E) on the new Telis 1 RTS briefly with the tip of...
Page 23
Take the new Telis 1 RTS and turn it over to access the PROG button (E). Press the PROG button (E) on the new Telis 1 RTS with the tip of a pencil until the product moves briefly (or a series of 3 beeps is emitted): the program-...
6.2 One lost or broken control point amongst others Find one of the control points linked to the product. Follow the steps described in the section "Adding the Telis 1 RTS" according to the control point model. N.B.: If, after having followed this operation, there is not a brief move- ment (or a series of beeps) the product, contact the Somfy assistance service so they can provide guidance for the replacement.
Telis 1 RTS N.B.: Do not attach the Telis 1 RTS to a metal surface as metal can interfere with the radio signal. 8. Everyday use of the Telis 1 RTS 8.1 Up and Down buttons Press the Up button (h): the product...
(+) and with text legible. Push the battery fully into its housing. Screw the rear casing of the Telis 1 RTS back on. Press a button on the front panel: if the indicator light comes on, the battery has been replaced correctly.
Page 28
Tel: +1 (0) 609 395 1300 Website: www.somfy.com/nam/index. cfm?language=en-us Somfy hereby declares that this product conforms to the essential requirements and other relevant provisions of Directive 1999/5/CE. A Declaration of Conformity is available at www.somfy.com/ce. For use in the European Union, the Swiss Confederation (Switzerland) and Norway.
Need help?
Do you have a question about the TELIS 1 RTS and is the answer not in the manual?
Questions and answers