Dk16 Pesu Circuit Card Wiring Diagram - Toshiba Strata DK 16 Installation And Maintenance Manual

TO PESU W/FEMALE
CONNECTOR
BRIDGING CLIPS
W-BL 26
1
BL-W 1
2
W-O 27
3
O-W 2
4
W-GN 28
5
GN-W 3
6
W-BR
29
7
BR-W 4
8
W-S 30
9
S-W 5
10
R-BL 31
11
BL-R 6
12
R-O 32
13
O-R 7
14
R-GN 33
15
GN-R
8
16
R-BR 34
17
BR-R 9
18
R-S 35
19
S-R 10
20
BK-BL 36
21
BL-BK 11
22
BK-O 37
23
O-BK 12
24
BK-GN
38
25
GN-BK 13
26
BK-BR 39
27
BR-BK 14
28
BK-S 40
29
S-BK 15
30
Y-BL 41
31
BL-Y 16
32
Y-O 42
33
O-Y
17
34
Y-GN 43
35
GN-Y 18
36
Y-BR 44
37
BR-Y 19
38
Y-S 45
39
S-Y 20
40
V-BL 46
41
BL-V 21
42
V-O 47
43
O-V 22
44
V-GN 48
45
GN-V 23
46
V-BR 49
47
BR-V 24
48
V-S 50
49
S-V 25
50
66M150 SPLIT BLOCK
NOTES: (Standard telephone circuits 1 & 2)
1. All cable 24 AWG; max loop resistance - 300 ohms from PESU to standard telephone/VM port.
2. Standard telephones may be on- or off-premises. Off-premises connection is made via OL13A FIC, and RJ21X jack.
3. Two ringers max per port.
4. Circuit 6 and 7 can provide interface for an external conference amplifier (Prog 10-3).
FIGURE 8-19

DK16 PESU CIRCUIT CARD WIRING DIAGRAM

STATION CABLING JACKETED TWISTED PAIRS (24 AWG)
TIP 1
1
RING 1
2
3
NOT USED
4
TIP 2
5
RING 2
6
7
NOT USED
8
9
CIRCUIT 3
10
NOT USED
11
12
(PORTS COUNT
13 IN SOFTWARE)
14
CIRCUIT 4
15
NOT USED
16
VOICE T1 (VT) 5
17
VOICE R1 (VR) 5
18
DATA T1 (DT) 5
19
DATA R1 (DR) 5
20
VT
21
VR CIRCUIT 6
22
TO ELECTRONIC
DT
23
TELEPHONE 2
DR
24
VT
25
VR CIRCUIT 7 TO
26
ELECTRONIC
DT
27
TELEPHONE 3
DR
28
VT
CIRCUIT 8 TO
29
VR
ELECTRONIC
30
TELEPHONE 4
DT
31
OR BGM
DR
32
(NOTE 5)
33
34
35
36 NOT USED
37
38
39
40
OCA T1 (OT) 5
41
OCA R1 (OR) 5
42
OT
43
CIRCUIT 6
OR
44
OT
45
OR CIRCUIT 7
46
OT
47
CIRCUIT 8
OR
48
49
NOT USED
50
8-23
INSTALLATION-WIRING DIAGRAMS
RJ11
R GN
BK
Y
W
BL
6 5 4 3 2 1
TIP RING
24
AWG STANDARD TELEPHONE 2
VOICE MAIL PORT OR
SIMILAR DEVICE
RJ11
VR VT
R
GN
DT BK
DR
Y
OCAT
W OCAR
BL
6 5 4 3 2 1
1 2 3 4 5 6
MODULAR
STATION
CORD
ELECTRONIC TELEPHONE
(NOTE 5)
STRAP OPTION:
P90 - RING VOLTAGE OPTION (CIRCUIT 1 & 2):
L = LOW LEVEL (130V P-P)
H = HIGH LEVEL (190V P-P)
NOTES: (Electronic telephone Circuits 5~8)
1.
To receive OCA, the 6500-series electronic telephone must
have an HVSU2 or the combined HVSI and HVSU installed.
2.
Program 31 , button/LED 03 must be "on" for electronic
telephone to receive OCA.
3.
An HHEU must be installed inside 6500-series electronic
telephones for headset or HESB; Loud Ringing Bell option.
4.
All cable 24 AWG, max 40 ohm loop resistance from PESU
to electronic telephone (1000 ft).
5.
HDSS connection is not available with PESU.
SECTION 100-816-208
MARCH 1993
RJ11
R GN
BK
Y
W
BL
6 5 4 3 2 1
TIP RING
STANDARD TELEPHONE 1
VOICE MAIL PORT OR
SIMILAR DEVICE
NOTE:
Two-ringers max may be
connected (high or low)
to Tip/Ring.
OT AND OR:
ONLY IF
ELECTRONIC
TELEPHONE
RECEIVES
OFF-HOOK CALL
ANNOUNCE CALLS