Toshiba ACE-tronics G9 ASD Installation And Operation Manual page 289

Block Read Data 4, 210
Block Read Data 5, 210
Block Write Data 1, 208
Block Write Data 2, 208
BRAKE A, B, and C switching relationship, 28
Brake Answer Wait Time, 182
BRAKE Output, 29
Brake Release Mechanical (Delay) Time, 232
Brake Sequence Response Error, 254
Brake-Release Torque (Proving) Time, 232
Brake-Release Torque Reference, 232
Brake-Release Torque Stable Time, 232
Brake-Seized Pulse Check Time, 233
Brake-Set Mechanical (Delay) Time, 232
Braking Resistance Overload Time (10x rated torque),
184
C
Cable/Terminal Specifications, 272
Carrier Frequency, 69
Carrier Frequency Control Mode, 142
CC, 25
Change Password, 78
Change Step Selection 1, 192
Change Step Selection 2, 192
Changed From Default, 40, 64
Changed From Default screen, 41
Charge LED, 9, 16
Circuit breaker configuration, 15
Circuit Breaker Part Number, 276
Clearing a Trip, 260
Clock Setup, 63
Closed Loop Hoist Control, 58
CM1, 249
CM2, 250
Command Control Selections, 50
Command Mode, 80
Command Mode and Frequency Mode Control, 47
Commercial Power Switching Freq. Hold Time, 150
Commercial Power Switching Wait Time, 150
Commercial Power/ASD Output Switching, 149
Commercial Power/ASD Switching Frequency, 150
Communication Adjustments, 76
Communication Error, 254
Communication Settings, 76
Communications, 76
Communications Option (DeviceNet/Profibus) Setting
1, 202
Communications Option (DeviceNet/Profibus) Setting
2, 203
Communications Option (DeviceNet/Profibus) Setting
8, 204
ACE-tronics G9 ASD Installation and Operation Manual
Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: CustomerService@valin.com
Communications Option
DeviceNet/CC-Link, 206
Communications Option Station Address Monitor, 205
Communications setting changes, 41
Compensation Frequency, 54
Conduit Plate Information, 261
Connecting the ASD, 16
Connection Diagram, 30
Continuous Dynamic Braking Capacity, 141
Continuous Monitoring Brake-Fail Pulse-Count, 233
Contrast, 64
Control Power Under-Voltage, 255
Cooling Fan Control, 180
CPU Fault, 255
CRANE / HOIST, 57
Crane/Hoist Settings, 69
Creep Control, 57
Creep Multiplier 1, 167
Creep Multiplier 2, 167
Creep Speed Lower Limit, 167
Current Control Proportional Gain, 163
Current/Voltage Specifications, 270
Current/Voltage Units Setup, 191
D
DBR Load, 55
DBR OL (Overload) Trip, 55
DBR over-current, 275
DBR Overload, 54
DC (Injection) Braking Current, 127
DC (Injection) Braking Start Frequency, 127
DC (Injection) Braking Time, 128
DC Bus Voltage, 54
DC Injection Braking, 65
DC Output, 25
Deceleration Suspend Frequency, 148
Deceleration Suspend Time, 148
Deceleration Time 1, 83
Deceleration Time 2, 169
Default Setting Changes, 40
Direct Access, 62
Disconnection Detection Extended Time, 205
Discrete Input, 25, 29
Discrete Input Terminal Assignment, 236
Discrete Input Terminals, 56
Discrete Output, 25
Display Bias, 192
Display Parameters, 62
Disposal, 3
Drooping, 143
Drooping Control, 73
Drooping Gain, 143
Speed Switch Monitor
279