Brother DCP-385C Quick Setup Manual

Unpack the machine and check the components
1
Start Here
Important
DO NOT connect the USB
cable before installing driver.
a.
Warnings tell you what to do to
WARNING
prevent possible personal injury.
c.
Press and slide the
paper side guides a and
paper length guide b to
fit the paper size.
Make sure that the
triangular marks c on
the paper side guides a
and paper length guide
b line up with the mark
for the paper size you
are using.
Install the ink cartridges
4
a.
c.
The LCD shows:
No Cartridge
Install Ink
Black
b.
Open the ink cartridge cover a.
1
Check the print quality
5
a. b.
When the preparation process Check the quality of the four color
has finished, the LCD shows this blocks a on the sheet.
message. (black/yellow/cyan/magenta)
Set Paper and Press
Start
Press Color Start.
o If all lines are clear and visible, press
The machine starts printing the
(Yes) to finish the quality check.
Print Quality Check Sheet.
o If you can see missing short lines, press
(No) and follow the steps on the LCD.
Before you can use the machine, read this Quick Setup Guide
for the correct setup and installation.
CHN-ENG
b.
Remove the green protective packing
Note
by lifting the front of the machine and then
• The components of your box may differ depending on your
pulling down on the packing part.
country.
• Save all packing materials and the box in case for any
reason you must ship your machine.
• Your machine has a USB interface that is compatible with
the USB 2.0 specifi cation.
• To ensure safe operation the supplied plug must be inserted
only into a standard power outlet that is properly grounded
through the standard electrical wiring. Non grounded
equipment may cause an electrical shock hazard, and may
cause excessive electrical noise radiation.
Remove the protective tape and film.
1
3
2
Important
Do not push the paper
in too far.
3
d.
Unpack the ink cartridge.
Remove the green protective part a.
Turn the green knob on the protective yellow cap clockwise until it
clicks to release the vacuum seal, then remove the cap a.
1
Set the LCD contrast (If needed)
6
a.
b.
c.
1
d.
e.
OK
f.
Poor
c.
a Make sure you have all components.
1 1
d. g.
Fan the stack of paper well. Close the paper tray cover
and slowly push the paper
e.
Gently put the paper into the tray back into the machine.
paper tray. Check that the paper
is flat in the tray.
f.
Gently adjust the paper side
guides to the paper with both
hands.
Make sure the paper side
guides touch the edges of the
paper.
e.
1
Set the date and time
7
a.
Press Menu.
Press a or b to choose General Setup.
press OK.
b.
Press a or b to choose LCD Settings.
press OK.
Press a or b to choose LCD Contrast.
c.
Press d or c to choose Light, Med or Dark.
press OK.
Press Stop/Exit.
Note
You can also adjust the angle of the display by
lifting it.
Inbox Ink
Cartridges [x4] 1
Black
Power Cord
Yellow
Cyan
Magenta
USB
Interface CD-ROM
Cable
Quick Setup
User's Guide
Guide
Approx. 65% yield of the replacement cartridge. For details, see
1
Consumable items in the User's Guide.
WARNING
Plastic bags are used in the packaging of your machine.
To avoid danger of suffocation, please keep these bags
away from babies and children.
Connect the power cord
3
h.
Pull out the paper support a until
it clicks, and then unfold the paper
support flap b.
2
1
Install each ink cartridge in the direction of the arrow on the
label.
Take care to match the color of the lever a with the
cartridge color b.
1 1
2
d.
Press Menu. Press a or b repeatedly to enter the last two digits of
the year, and then press OK.
Date&Time
Press a or b to choose
Year:20
Initial Setup, and then press OK.
08
MENU
Press a or b to choose
Date&Time, and then press OK. (e.g. Enter 08 for 2008.)
e.
Repeat for Month and Day, and Hours and Minutes
Note
in 24-hour format.
If you make a mistake and want to start again,
press Stop/Exit to go back to step a.
f.
Press Stop/Exit.

Quick Setup Guide

DCP - 385C
Load plain A4 paper
2
a.
Pull out the paper tray.
b.
Lift the paper tray cover a.
1
a.
Connect the power cord.
WARNING
The machine must be fi tted with an earthed plug.
Important
DO NOT connect the USB cable
before installing driver.
Note
The control panel warning
LED will stay on until you have
installed the ink cartridges.
f.
Gently push the ink cartridge until it clicks. After all the ink
cartridges are installed close the ink cartridge cover.
Important
After initial installation of the ink cartridges, the machine will start cleaning the
ink tube system. This cleaning process will last approximately four minutes.
DO NOT unplug the machine from the power outlet or attempt to stop the
cleaning process. Interruption of cleaning process may cause undesired print
quality problems.
Input & Press OK
Turn the sheet over.