Brother DCP-385C Quick Setup Manual

Unpack the machine and check the components
1

Start Here

Important
DO NOT
connect the
USB cable yet.
a.
Warnings tell you what to do to
WARNING
prevent possible personal injury.
d.
e.
f.
Important
Do not push the paper
in too far.
Install the ink cartridges
5
a. c.
The LCD shows:
No Cartridge
Install Ink
Black
b.
Open the ink cartridge cover a.
1
Check the print quality
6
a. b.
When the preparation process Check the quality of the four colour
has finished, the LCD shows this blocks a on the sheet.
message. (black/yellow/cyan/magenta)
Set Paper and Press
Start
Press Colour Start.
o If all lines are clear and visible, press
(Yes) to finish the quality check.
o If you can see missing short lines, press
(No) and follow the steps on the LCD.
Before you can use the machine, read this Quick Setup Guide
for the correct setup and installation.
LS6233004
UK/IRE/GEN/SAF
Printed in China
b.
Remove the green protective packing
Note
by lifting the front of the machine and then
• The components of your box may differ
pulling down on the packing part.
depending on your country.
• Save all packing materials and the box in
case for any reason you must ship your
machine.
• A USB cable is not included.
You need to purchase a USB 2.0 cable
that is no more than 2 metres long.
1 1
c.
Remove the plastic bag
Remove the protective tape and film.
cartridges from on top of the paper tray.
g.
Fan the stack of paper well. Close the paper tray cover
and slowly push the paper
Gently put the paper into tray back into the machine.
the paper tray.
Check that the paper is flat
in the tray.
Gently adjust the paper side
guides to the paper with
both hands. Make sure the
paper side guides touch the
edges of the paper.
d.
Remove the green protective part a. Unpack the ink cartridge.
Turn the green knob on the protective yellow cap clockwise until it clicks to release the vacuum
seal, then remove the cap a.
1
1
Set the LCD contrast (If needed)
7
a.
b.
Press OK.
c.
1
Press OK.
d.
e.
OK
Press OK.
f.
Press Stop/Exit.
Poor
d.
a
Make sure you have all components.
Inbox Ink
Cartridges [x4]
2
Black
Yellow
Cyan
Magenta
Power Cord CD-ROM
Quick Setup
User's Guide
Guide
1 Approx. 65% yield of the replacement cartridge. For details, see
Consumable items in the User's Guide.
WARNING
b containing the ink
Plastic bags are used in the packaging of your
machine. To avoid danger of suffocation, please
keep these bags away from babies and children.
Connect the power cord
3
h. a.
Pull out the paper support Connect the power cord.
a until it clicks, and then unfold
the paper support flap b.
2
1
Set the date and time
8
Press Menu.
Press a or b to choose General Setup.
Press a or b to choose LCD Settings.
Press a or b to choose LCD Contrast.
Press d or c to choose Light, Med or Dark.
Note
You can also adjust the angle of the display by
lifting it.
Load plain A4 paper
2
a.
Pull out the paper tray.
1
b.
Lift the paper tray cover a.
1
Set the language
4
WARNING
The machine must be fi tted with an earthed plug.
Important
DO NOT connect the USB cable
yet.
Note
The control panel warning
LED will stay on until you have
installed the ink cartridges.
e.
Install each ink cartridge in the direction of the arrow on the label.
a
Take care to match the colour of the lever with the cartridge
colour b.
1 1
2
a. d.
Press Menu. Press a or b repeatedly to enter the last two digits of
the year, and then press OK.
b.
Press a or b to choose
Date&Time
Initial Setup, and then press OK.
Year:20
08
c.
Press a or b to choose
Date&Time, and then press OK.
MENU
(e.g. Enter 08 for 2008.)
e.
Repeat for Month and Day, and Hours and Minutes
Note
in 24-hour format.
If you make a mistake and want to start again,
press Stop/Exit to go back to step a.
f.
Press Stop/Exit.
Quick Setup Guide
DCP - 385C
DCP - 383C
DCP - 387C
c.
Press and slide the
1
paper side guides
a and paper length
b
guide to fit the
paper size.
3
Make sure that the
triangular marks c
2
on the paper side
a
guides and paper
length guide b line
up with the mark for
the paper size you
are using.
3
a. b.
After connecting the power Choose Yes or No and press
cord, the LCD shows: OK.
Select Language English
English Yes
Français No
Deutsch
Nederlands
Italiano
Select Language Select & Press OK Select Language Select & Press OK
Press a or b to choose your
language and press OK.
Note
• The languages available may differ depending on your country.
• If you set the wrong language, you can change it again after
setting the date and time.
(For details see Changing LCD language in Chapter 3 of the User's Guide.)
f.
Gently push the ink cartridge until it clicks. After all the
ink cartridges are installed close the ink cartridge cover.
Note
The machine will prepare the ink tube system for printing.
This process will take approximately four minutes.
Do not turn off the machine.
Input & Press OK
Turn the sheet over.