Advertisement
Quick Links
Cordless Angle Drill
Capacities
Steel
Wood
Wood
screw
10
mm (3/8")
MODEL DA390D
10
mm (3/8") MODEL DA390DW
With Fast Charger
weight
N o
load speed
Dimensions
(L x W x HI
(RPMI
INSTRUCTION MANUAL
1 0
mm
(318")
SPEC IF I CAT I 0 N S
335
mm x
59
mm
x
115
mm
(13-1/4"
x
2-3/8"
x
4-1/2"1
1.3 kg
12.9
Ibsl
800
1 2
mm
4.5
mm
x
2 0
mm
(15132")
(3116"
x
314")
Model DA390D
Battery Cartridge 9000
Model DC9700 Fast Charger
Voltage
I
Charging time
I
Input
I
output
9.6 V
I
1 Hr.
I
A . C .
only 50 H z
-
60 Hz
I
D.C. 7.2 V
~
9.6 V
*
Manufacturer reserves the right t o change specifications w i t h o u t notice.
*
Note: Specifications m a y differ from country t o country.
Advertisement
Related Manuals for Makita CORDLESS ANGLE DRILL DA390D
Summary of Contents for Makita CORDLESS ANGLE DRILL DA390D
- Page 1 Cordless Angle Drill INSTRUCTION MANUAL SPEC IF I CAT I 0 N S Model DA390D Capacities Steel Wood Wood (318”) (15132”) (3116“ Battery Cartridge 9000 Voltage Charging time 9.6 V 1 Hr. Manufacturer reserves the right t o change specifications w i t h o u t notice. Note: Specifications m a y differ from country t o country.
-
Page 2: Important Safety Instructions
SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. - Page 3 REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. OUTDOOR USE EXTENSION CORDS.
- Page 4 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Length of Cord (Feet) AWG Size of Cord Do not operate charger with damaged cord or plug mediately. Do not operate charger if otherwise damaged in any way; take Do not disassemble charger or battery cartridge; take serviceman when service or repair is required.
-
Page 5: Additional Safety Rules
ADDITIONAL FOR CHARGER & BATTERY CARTRIDGE not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 4OoC or ABOVE (104OF). not attempt t o use a step-up transformer, an engine generator or DC power receptacle. Do not allow anything t o cover or clog the charger vents. 4. - Page 6 Installing or removing battery cartridge 0Always switch off the tool before insertion or removal of the battery cartridge. To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel.
- Page 7 When you charge a new battery cartridge or a battery cartridge which has for a long period, it may not accept a full charge. not indicate problem. You can recharge the battery cartridge fully after discharging it almost completely a couple of times. If you wish t o charge two battery cartridges, allow 15 minutes between chargings on the fast charger.
- Page 8 Drilling operation Drilling in wood When drilling in wood, best results are obrained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. Drilling in metal prevent the b i t from slipping when starting a hole, make an indentation with a center- punch and hammer a t the point t o be drilled.
- Page 9 Always be sure that the tool attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized Makita replacement parts. switched off and the battery cartridge i s removed before...
- Page 10 C A U T I O N : These accessories o r attachments are recommended for use w i t h your Makita t o o l specified manual. The use of any other accessories or attachments might present a risk of injury t o persons.
- Page 11 June-16'89 10 mm (3/8") CORDLESS ANGLE DRILL Model DA390D Note: The switch and other part configurations may differ from country to country.
- Page 12 SPeCIfICattons may MAKITA LIMITED ONE YEAR WARRANTY tvery Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted t o be free defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.