Advertisement
Quick Links
V
V
European Community Declarations
Manufacturer:
DrayTek Corp.
Address:
No. 26, Fu Shing Road, HuKou Township, HsinChu Industrial Park, Hsin-Chu, Taiwan 303
Product:
VigorSwitch P
DrayTek Corp. declares that VigorSwitch P1080 is in compliance with the following essential requirements and other relevant
provisions of 2004/108/EC.
The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive 2004/108/EC by complying with
the requirements set forth in EN55022/Class A and EN55024/Class A.
The product conforms to the requirements of Low Voltage (LVD) Directive 2006/95/EC by complying with the requirements
.
set forth in EN60950-1
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device may accept any interference received, including interference that may cause undesired operation.
i
g
o
r
S
w
i
g
o
r
S
w
8
-
P
8
-
P
E
t
h
e
r
n
E
t
h
e
r
Quick Start Guide
1080
Version: 1.01
Date: 15/03/2011
i
t
c
h
P
i
t
c
h
P
o
r
t
P
o
o
r
t
P
o
e
t
S
w
n
e
t
S
w
1
0
8
0
1
0
8
0
E
E
i
t
c
h
i
t
c
h
Advertisement
Related Manuals for Draytek VigorSwitch P1080
Summary of Contents for Draytek VigorSwitch P1080
-
Page 1: Quick Start Guide
1080 Product: VigorSwitch P DrayTek Corp. declares that VigorSwitch P1080 is in compliance with the following essential requirements and other relevant provisions of 2004/108/EC. The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive 2004/108/EC by complying with the requirements set forth in EN55022/Class A and EN55024/Class A. -
Page 2: Package Content
Package Content This switch provides 8 10/100M PoE ports. It was designed for easy installation and high performance in an environment where PoE devices might need to be connected to the network. The switch consists of 8 PSE/PoE ports. Providing power to devices via PoE can offer a solution where power outlet availability is limited and offer the system designer a flexible solution to locate the network device anywhere. - Page 3 Descriptions of Panel Status Explanation The device is powered on. The device is powered off. A normal connection is through its corresponding port. LAN is disconnected. Blinking Data is transmitting (sending/receiving). Connect to a Power Device. No Power Device is connected. Interface Description Power inlet for AC input (100~240V/AC, 50~60Hz).
- Page 4 Installing Your Switch Power Device to This Switch and Getting 48V Power Source through Cat. 5 Cables Use a Cat. 5 twisted-pair cable to connect a PoE device to the port (1~8) of this switch. This switch will supply 48V power to PoE Device over Cat. 5 twisted-pair cable.