The following show the symbols used for the equipment. characteristics. Be sure that you understand their meaning before use. ・ Read instruction manual. ・ For Model GA7030,GA7030S DOUBLE INSULATION ENG102-3 Noise ・ Wear safety glasses. The typical A-weighted noise level determined according to EN60745: ・...
Page 3
ENG208-5 exposure in the actual conditions of use (taking Vibration account of all parts of the operating cycle such as The vibration total value (tri-axial vector sum) determined the times when the tool is switched off and when it according to EN60745: is running idle in addition to the trigger time).
Page 4
Makita Corporation responsible Electrical safety manufacturer declare that the following Makita Power tool plugs must match the outlet. Never machine(s): modify the plug in any way. Do not use any Designation of Machine: adapter plugs with earthed (grounded) power Angle Grinder tools.
12. Use personal protective equipment. Always 23. Keep cutting tools sharp and clean. Properly wear eye protection. Protective equipment such maintained cutting tools with sharp cutting edges as dust mask, non-skid safety shoes, hard hat, or are less likely to bind and are easier to control. hearing protection used for appropriate conditions 24.
Page 6
Do not use a damaged accessory. Before each 15. Do not operate the power tool near flammable use inspect the accessory such as abrasive materials. Sparks could ignite these materials. wheels for chips and cracks, backing pad for 16. Do not use accessories that require liquid cracks, tear or excess wear, wire brush for coolants.
Page 7
so the least amount of wheel is exposed Safety Warnings Specific for Sanding Operations: towards the operator. The guard helps to protect a) Do not use excessively oversized sanding operator from broken wheel fragments and disc paper. Follow manufacturers accidental contact with wheel. recommendations, when selecting sanding paper.
28. Do not use separate reducing bushings or FUNCTIONAL DESCRIPTION adaptors to adapt large hole abrasive wheels. 29. Use only flanges specified for this tool. 30. For tools intended to be fitted with threaded CAUTION: hole wheel, ensure that the thread in the wheel Always be sure that the tool is switched off and •...
Page 9
Installing side grip (handle) 1. Switch trigger 2. Lock lever 006734 For tool with the lock-on switch 006735 To start the tool, simply pull the switch trigger (in the B CAUTION: direction). Release the switch trigger to stop. For Always be sure that the side grip is installed continuous operation, pull the switch trigger (in the B •...
Page 10
For tool with clamp lever type wheel guard Super flange Models 1. Wheel guard GA7030F,GA7030SF,GA7040F,GA7040SF,GA9030F, 2. Bearing box 9030SF,GA9040F GA9040SF 3. Nut standard-equipped with a super flange. Only 1/3 of 4. Lever efforts needed to undo lock nut, compared with conventional type.
tighten the lock nut, press the shaft lock firmly so that the Operation with wire cup brush (optional spindle cannot revolve, then use the lock nut wrench and accessory) securely tighten clockwise. To remove the disc, follow the installation procedure in CAUTION: reverse.
Thread wire wheel brush onto spindle and tighten with For Australia and New Zealand the wrenches. Installing or removing abrasive cut-off wheel / When using wire wheel brush, avoid applying too much diamond wheel (optional accessory) pressure which causes over bending of wires, leading to premature breakage.
Page 13
If you need any assistance for more details regarding 001146 these accessories, ask your local Makita Service Center. When the resin insulating tip inside the carbon brush is exposed to contact the commutator, it will automatically shut off the motor.
Page 14
Side grip Wheel guard for Depressed center grinding wheel/Multi-disc / Wire wheel brush Inner flange / Super flange / Inner flange 102 (Australia and New Zealand only) Depressed center grinding wheel/Multi-disc Lock nut / Ezynut*1 Wheel guard for Abrasive cut off wheel / Diamond wheel *2 Dust collecting wheel guard Inner flange / Super flange / Inner flange 78 (Australia and New Zealand only) Abrasive cut off wheel / Diamond wheel...
Page 16
Makita Corporation Anjo, Aichi, Japan www.makita.com 884649E228...