Honeywell HRXD Quick Installation Manual

HRXD Quick Installation Guide
Step 1: Connect Cameras, Peripherals
Connect up to 16 cameras,
depending on your DVR model.
Power Connector Audio Alarm
In/Out Inputs
Note Use the SVHS input for your
main monitor, if possible. It
will give you better quality
video display.
RS485 Connector Pin Outs
Master Unit Slave Unit
+ ! To ! TX+
– ! To ! TX–
+ ! To ! RX+
– ! To ! RX–
Step 2: Configure the DVR

Settings Overview

1. Connect the power cord to the unit. It takes approximately 60 seconds
to power up.
2. Throughout the screens you will see
will reset the screen to its default settings.
3. Press MENU on the front panel to enter the setup screens. Select a
User and enter the password by pressing the camera number buttons
and then . There is no default password when logging in the admin
user for the first time.
4. Highlight Information and press
can set the DVR language and upgrade the software.
5. Highlight Date/Time in the System menu and press
and time. Select the appropriate DST option.
6. To add, edit and delete users and groups of users, highlight User in
the System menu and press
7. To set up your Network connection and other network options,
highlight Network in the Network menu and press
8. Highlight Camera in the Devices menu and press
cameras and PTZ domes.
9. Highlight Alarm-Out in the Devices menu and press
settings and establish a schedule for each alarm output device used.
10. Highlight Display and press
on the main monitor (for example, date, time and camera number).
11. To set up your recording options, use the screens in the Record menu.
Here you will find general recording settings along with schedules, pre-
event and archive options.
12. Set up your Event options in the Event menu:
a. Select Alarm-In and press
b. Highlight Motion Detection and press
detections settings.
c. Select Video Loss to set up Video Loss event options.
d. Highlight Text-In and press
e. Highlight Event Status and press
status of the DVR.
Edit Text/Screen Titles and Numerical Values
!
Select the line, then press .
"
If the field is numerical, use the cursor controls
or inner jog wheel to adjust the value.
Press to move cursor up or to increase
numerical values by 1.
Press to
Use the inner jog
move left.
wheel to rapidly
increase or
decrease a
numerical value.
Press to move cursor down or to decrease
numerical values by 1.

General Recording Settings

! "
Record Menu Record.
Make sure Recycle is checked. Select your Make sure Schedule On is checked to
Resolution, Event Record Dwell time and program the DVR to record based on time,
Auto Deletion option. If you are using Panic day of the week, and holidays. Select + to
Recording, set those options as needed. add a schedule item. For each new
schedule item you will need to set the day
and time range, recording mode and
channels to be recorded.
For more detailed information, refer to the HRXD User Guide and the HRXD RAS Guide on your
CD and at www.honeywellvideo.com.
SVHS Out
Video Out
Video In
Factory USB RS232 VGA Alarm SCSI
Reset Port Port Port Outputs Port
Switch
Note You cannot mix NTSC and PAL
equipment. For example, you
cannot use a PAL camera and an
NTSC monitor.
I/O Connector Pin Outs
AI (1 to 16) Alarm Inputs 1 to 16
GND Chassis Ground (9 connectors)
AO (1 to 16) Alarm Outputs 1 to 16
ARI Alarm Reset In
. Highlighting
. From the Information screen you
(see New User Setup for details).
.
to set up your
to select what information to display
to set up your Alarm Inputs.
to change your motion
to set up your Text event options.
to check the current event
"
If the field is a text line, use the
Text Entry screen to edit the text.
Press to confirm the entry and
select OK to confirm entered text.
Press to move
right.
Record Menu Schedule.
#
Record Menu
Schedule
For each new schedule
item, select Settings and
press
images per second and
Quality of the recording for
any modes you set in the
Mode column.
Spot Out
RS485
"
Activate each
input being used
and give it a
Title. Set each
input as either
normally open
(NO) or normally
Alarm Ethernet
closed (NC).
Reset Port
In
#
Event Menu
Highlight Actions 1 to open the Actions 1 setup
screen. Set the actions the DVR will take when it
senses an input in the Alarm-Out column. Also
select which cameras the DVR should record
when an alarm is present.
and pressing
$
Event Menu
Motion Detection
Zone screen.
You can define the
area of the image
where you want to
detect motion (a
doorway, for
to set the date
example).
Highlight the box
under Zone and
press . The
Zone screen is laid
over the video for
the selected
camera. Set up the
motion detection
zones by selecting
and clearing
to change the blocks.
&
Event Menu
From this screen, the DVR can be set to react differently
to each motion detection. You can associate multiple
cameras with the motion detecting camera, recording
video from all the associated cameras when motion is
detected. In the Alarm-Out field you can select which
alarm outputs will be triggered when motion is detected.
You can also select which devices or users will be
notified when motion is detected.
Step 3: Daily Operation
!
System Menu
users and user groups, select User in the
System menu. Delete Users or Groups by
selecting the corresponding
pressing . Highlight a User Name and
Settings.
press to add or change the password
assigned to that User. You can also change
the User's group.
. You can set the
Set Event Alarm Settings
!
Event Menu Alarm-In Settings.
Set up each alarm input from the
terminal strip on the back of the DVR.
Alarm-In Actions 1.
$
Event Menu
Actions 1
Select the Notify field for an
alarm input to set who will
be notified when the alarm is
detected.
Set Motion Detection Settings
!
Event Menu Motion Detection Settings.
From this screen, video motion detection can be
turned on or off for each camera.
Motion Detection Actions 1.
Password
Select a User and enter the password by pressing the appropriate
combination of Camera number buttons and then
password when logging in as the admin user for the first time.
Note To assure the secure management of the system, setting up a
password is strongly recommended.
New User Setup
User. To set up your
and
#
System Menu User New
Group. Select + Group... on the User
setup screen and press . Use the
virtual keyboard to enter the new
Group Name. Assign the Authority
level for the group by selecting the
appropriate Authority boxes.
For Front Panel Operation, see over.
%
Event Menu Alarm-In Actions 2. Highlight
Actions 2 to open the Actions 2 setup screen. On
this screen, select the PTZ presets to run and spot
monitors to display when an alarm is present.
Alarm-In
Notify.
"
Event Menu Motion Detection Sensitivity.
Adjust the DVR's sensitivity to motion for Daytime and
Nighttime independently (set from 1, low, to 5, high).
#
Event Menu
Motion Detection
Min. Blocks. Adjust
the minimum number
of detection blocks for
Daytime or Nighttime
independently. Smaller
numbers of Minimum
Blocks provide greater
sensitivity.
%
Event Menu
Motion Detection
Zone Screen Zone
Menu. Select a motion
zone block and press
. Use this menu to
activate (Select) or
deactivate (Clear)
blocks for motion
detection.
'
Event Menu Motion Detection Actions 2.
From this screen, the DVR can be set to react differently
to each motion detection. You can select a PTZ preset
position for each PTZ camera to move to when motion is
detected. In the Spot Monitor field you can associate a
different camera with each spot monitor, so that specific
cameras will be displayed on the spot monitors when
motion is detected.
. There is no default
"
System Menu User
New User. Select + User... on
the User setup screen and
press . Use the virtual
keyboard to enter the new
User Name. Assign the User to
a Group and enter a password
with the camera buttons.