Linksys SPA9000 Quick Installation

Package Contents
• IP Telephony System
• Power Adapter
• RJ-45 Ethernet Cable
• Quick Installation
IP Telephony System
Quick Installation
Voice
SPA9000
Model No. Model No.
Before You Begin
For first-time installation of the System, Linksys strongly recommends that you
run the Setup Wizard, which you can download from www.linksys.com . For
advanced users, you may follow the instructions in this Quick Installation.
Make sure you have the following:
• IP Telephony System
Internet
• One or more Internet phones
(for example, Linksys SPA-family
IP Phones, model number: SPA941 Cable/DSL Modem
SPA941)
• A router and cable/DSL
Router Desktop
SPA941 Switch
modem (or gateway)
Computer
• One or more Ethernet network
switches (so you can connect SPA941
Internet phones or computers)
• At least one active Internet
phone service account and its
settings if you want to make
external calls
Analog Fax Administration
• An active Internet connection
Phone Computer
if you want to make external
A Typical Scenario
calls
• At least one computer for
NOTE: For best results, use a
configuration of the System
switch that offers QoS (Quality of
and Internet phones
Service) and full wire-speed
switching. QoS enables the switch to
• Two or more Ethernet network
give top priority to voice traffic, while
cables
full wire-speed switching lets it
forward packets as fast as your
• Analog telephones or fax
network can deliver them. The next
machines (optional)
best choice is a QoS (Quality of
Service) switch.
VoIPon www.voipon.co.uk
1
Install the IP Telephony System
A
Plug an analog telephone
into the Phone 1 port of the
System. (optional)
B
If you have a second
analog telephone or fax A
machine, plug it into the
Phone 2 port. (optional)
IMPORTANT: Do not connect the
C
Phone port to a telephone wall jack.
Connect an Ethernet
Make sure you only connect a
network cable to the
telephone or fax machine to the
Internet port of the System.
Phone port. Otherwise, the System or
Connect the other end to
the telephone wiring in your home or
one of the Ethernet ports on
office may be damaged.
your router.
D
Connect a different
Ethernet network cable to
the Ethernet port of the
System. Then connect the
C
other end to the computer
you will use to manage the
System (this will be the
administration computer).
E
Connect the included
power adapter to the Power
D
port of the System, and then
plug the power adapter into
an electrical outlet.
F
Launch the web browser on
the administration
computer. E
G
Enter 192.168.0.1/admin/
voice/advanced in the
Address field. Press Enter.
NOTE: 192.168.0.1 is the default
local IP address of the System.
sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 600030
H
The Voice - Info screen will
appear. Click the SIP tab.
I
In the PBX Parameters
section, select WAN for the
Proxy Network Interface.
J
Click Submit All Changes.
K
I
The Voice - Info screen will
appear. Click the Router
tab.
L
Click the WAN Setup tab.
M
For the Connection Type,
select Static IP .
N
In the Static IP Settings
section, complete the
following fields:
Static IP - Enter a static IP
address appropriate for
your network. Write this
down; you will use it later.
M
NetMask - Enter the subnet
mask of your router.
NOTE: Make sure your router will
not assign the System's IP address to
Gateway - Enter the local IP
any other device. For example, you
address of your router or
can assign an IP address outside of
gateway.
your router's DHCP IP address range;
however, it must be within the
router's subnet range.
For information about IP addressing,
refer to the router's documentation.
O
In the Optional Settings
section, complete the
Primary DNS
field.
Primary DNS - Enter the DNS
IP address of your router.
P
In the Remote
Management section,
select yes from the Enable
WAN Web Server drop-down
menu.
Q
Click Submit All Changes.
R
The Router - Status screen
will appear. Verify that the
following settings match
your entries:
• WAN Connection Type -
Static IP
• Current IP
• Current NetMask
• Current Gateway
• Primary DNS
Proceed to the next section.