Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for GE Interlogix KTD-125
Summary of Contents for GE Interlogix KTD-125
- Page 1 KTD-125/125-24 KTD-125P/125P-24 KTD-127/127W PTZ Receivers...
- Page 2 © 2003 Kalatel, a GE Interlogix company All Rights Reserved. Any GE Interlogix, Kalatel division, software This equipment has been tested and supplied with GE Interlogix, Kalatel division, found to comply with the limits for a products is proprietary and furnished under...
-
Page 3: Table Of Contents
KTD-125/127 PTZ Receivers User Manual Table of Contents ABLE OF ONTENTS ..............4 EFORE EGIN ..............5 NTRODUCTION ........6 ETTING THE UTOPAN UMPER KTD-125 U ..........8 NSTALLING NITS 3.1 M ..........8 OUNTING THE 3.2 M .........11 AKING ABLE ONNECTIONS 3.2.1 KTD-125P Preset Positioning........16 KTD-127 ..........18... -
Page 4: Before You Begin
Before You Begin KTD-125/127 PTZ Receivers User Manual EFORE EGIN Read these instructions before installing or operating this product. Note: This installation should be made by a qualified service person and should conform to local codes. This manual provides installation and operation information. To use this document, you must have the following minimum qualifications: •... -
Page 5: Introduction
KTD-125/127 PTZ Receivers User Manual Introduction NTRODUCTION Use a KTD-125/127 PTZ receiver and a Kalatel keypad to interface with equipment from other manufacturers and simplify common security system functions. See Table 1 for an overview of KTD-125 and KTD-127 PTZ receiver features. See Figure 1 for a typical system diagram. -
Page 6: Setting The Autopan Jumper
Determine whether or not your pan/tilt drive has an internal reversing switch. (See Appendix A, Determining the Type of Pan/Tilt Drive.) Locate the autopan jumper. For KTD-125 units see Figure 2; for KTD-127 units see Figure 3. Figure 2. KTD-125 autopan jumper location Figure 3. - Page 7 KTD-125/127 PTZ Receivers User Manual Setting the Autopan Jumper See Figure 4 to set the autopan jumper. Connect for pan/tilt units without an internal reversing switch Disconnect for pan/tilt with an internal reversing switch Figure 4. Selecting the autopan jumper setting Note: If the pan/tilt drive has an internal reversing switch, connect the pant/tilt drive’s...
-
Page 8: Installing Ktd-125 Units
Installing KTD-125 Units KTD-125/127 PTZ Receivers User Manual KTD-125 U NSTALLING NITS CAUTION: Complete all instruction steps before supplying power to the unit. OUNTING THE To mount the unit see Figure 5, Figure 6, and Figure 7 and perform the following. - Page 9 KTD-125/127 PTZ Receivers User Manual Installing KTD-125 Units Figure 6. Pulling the main relay board away from the standoffs (KTD-125P-24 shown) Note: You may need to bend the board slightly to remove it from the housing. Board brackets (2) Figure 7. Pushing the board brackets inward to free the board from the housing.
- Page 10 Installing KTD-125 Units KTD-125/127 PTZ Receivers User Manual To mount the housing use installer-provided fasteners and the four mounting holes in the mounting flanges (Figure 8). Note: Install the housing so that it is level and the door opens to the left.
-
Page 11: Making Cable Connections
KTD-125/127 PTZ Receivers User Manual Installing KTD-125 Units AKING ABLE ONNECTIONS For the following procedures, see Figure 9 for KTD-125/125P units and Figure 10 for KTD-125-24/125P-24 units. Watertight cable openings Camera power/zoom lens Pan/tilt Removable terminal strips 24 VAC power connector... - Page 12 Remove the outer casing from the end of the RS422 cable(s). To make the cable connections perform the following. CAUTION: For the KTD-125-24 and KTD-125P-24 units, connect only 110 VAC input to the power cable pigtail. 1040823A / June 2003...
- Page 13 KTD-125/127 PTZ Receivers User Manual Installing KTD-125 Units CAUTION: For the KTD-125 and KTD-125P units, connect only 24 VAC input to the power cable pigtail. Use wire nuts to connect the power cable conductors to the power cable pigtail. (See Table 2.) Table 2.
- Page 14 D = Down R = Right A = Auto Figure 12. KTD-125 Pan/Tilt Connections Spare relay contact R = Relay Contact Figure 13. KTD-125 Spare Relay Connections Lens control cable I = Iris F = Focus Z = Zoom COM. = Common Figure 14.
- Page 15 Connect the RS422 control cable(s) as shown in Figure 15. RS422 control in RS422 control out Figure 15. KTD-125 RS422 control cable connections to the receiver card For the programming preset positions with the KTD-125P, see section 3.2.1, KTD-125P Preset Positioning.
-
Page 16: Ktd-125P Preset Positioning
Installing KTD-125 Units KTD-125/127 PTZ Receivers User Manual 3.2.1 KTD-125P P RESET OSITIONING The KTD-125P/125P-24 receivers can find up to 10 preset positions if the camera lens and pan/tilt drive are equipped with feedback potentiometers. If you program the 10 positions from the controller keypad, you can find a maximum of eight through contact closures into the receiver’s KTD-125C receiver card. - Page 17 KTD-125/127 PTZ Receivers User Manual Installing KTD-125 Units Relay output Preset alarm input contacts Figure 17. Preset and output relay contact connections 1040823A / June 2003...
-
Page 18: Installing The Ktd-127
Installing the KTD-127 KTD-125/127 PTZ Receivers User Manual KTD-127 NSTALLING THE CAUTION: Complete all instruction steps before supplying power to the unit. OUNTING THE Note: In most cases, it is easier to mount the unit with the main relay board removed. - Page 19 KTD-125/127 PTZ Receivers User Manual Installing the KTD-127 Figure 19. Sliding out the KTD-127 card To mount the housing use the two mounting holes in the housing (Figure 20) and installer-provided fasteners. Mounting holes (2) Figure 20. Mounting holes in KTD-127 housing Note: Do not reinstall the main relay board until instructed to do so in section 6, Completing and Testing the Installation (All Units).
-
Page 20: Aking Able Onnections
Installing the KTD-127 KTD-125/127 PTZ Receivers User Manual AKING ABLE ONNECTIONS See Figure 21 for the following procedures. Removable terminal strip Receiver card Camera power/zoom lens Pan/tilt 24 VAC power RS422 control out RS422 control out Figure 21. KTD-127 cable connections To prepare the cables for connection perform the following. - Page 21 KTD-125/127 PTZ Receivers User Manual Installing the KTD-127 To power 1/HOT = Hot 2/COM. = Common Figure 22. KTD-127 Terminal Strip Connections, Power To camera 3 / HOT = Hot 11 / I = Iris 13 / Z = Zoom 4 / COM.
- Page 22 Installing the KTD-127 KTD-125/127 PTZ Receivers User Manual Remove the four-connection terminal strip from the receiver card on the main relay board. Note: Observe polarity when you connect the RS422 control cables Connect the RS422 control cable(s) as shown in Figure 25.
-
Page 23: Installing The Ktd-127W
KTD-125/127 PTZ Receivers User Manual Installing the KTD-127W KTD-127W NSTALLING THE CAUTION: Complete all instruction steps before supplying power to the unit. OUNTING THE Note: In most cases, it is easier to mount the unit with the main relay board removed. - Page 24 Installing the KTD-127W KTD-125/127 PTZ Receivers User Manual Figure 27. Pulling the board away from the standoffs Note: You may need to bend the board slightly to remove it from the housing. Figure 28. Pushing the board brackets inward to free the board from the housing.
- Page 25 KTD-125/127 PTZ Receivers User Manual Installing the KTD-127W To mount the housing use installer-provided fasteners and the four mounting holes in the mounting flanges (Figure 29). Note: Install the housing so that it is level and the door opens to the left.
-
Page 26: Making Cable Connections
Installing the KTD-127W KTD-125/127 PTZ Receivers User Manual AKING ABLE ONNECTIONS See Figure 30 for the following procedures. Removable terminal strip Receiver card Camera power/zoom lens Pan/tilt 24 VAC in RS422 control out RS422 control in Figure 30. KTD-127W cable routing To prepare the cables for connection perform the following. - Page 27 KTD-125/127 PTZ Receivers User Manual Installing the KTD-127W To power 1/HOT = Hot 2/COM. = Common Figure 31. KTD-127W Terminal Strip Connections, Power camera 3 / HOT = Hot 11 / I = Iris 13 / Z = Zoom 4 / COM. = Common 12 / F = Focus 14 / COM.
- Page 28 Installing the KTD-127W KTD-125/127 PTZ Receivers User Manual Remove the four-connection terminal strip from the receiver card on the main relay board. Note: Observe polarity when you connect the RS422 control cables Connect the RS422 control cable(s) as shown in Figure 34.
-
Page 29: Completing The Installation (All Units )
To test for proper installation, perform the following. Check all connections. Supply power to the unit. If you have a KTD-125 unit, confirm that the power switch on the main relay board is on. Test for proper operation using the on-site toggle switches on the main relay board. -
Page 30: Programming The Units
Programming KTD-125/127 PTZ Receivers User Manual ROGRAMMING THE NITS The KTD-125 and KTD-127 PTZ receivers have several mode-of- operation choices that you must program before you operate the units. Typically, you would program the receiver with a Kalatel controller keypad. - Page 31 KTD-125/127 PTZ Receivers User Manual Programming Note: When reentering programming mode, you must reprogram all mode-of-operation choices, even if you are only changing one. Table 3. Setting DIP switches for the desired mode of operation Function Setting Switch Zoom Polarity...
-
Page 32: Assigning A Site Address
Programming KTD-125/127 PTZ Receivers User Manual SSIGNING A DDRESS CAUTION: Make sure the receiver is in normal operating mode before changing DIP switches 1 through 9 for site addressing. To assign a site address perform the following. Note: You can assign a site address while the unit has power. -
Page 33: Ppendix B. Using Ite Oggle Witches
Figure 37. KTD-127 units Zoom Focus Iris Spare Tilt ▼ ▼ ▼ ▼ ▼ ▼ ▼ ► Near Open Manual Left ► Down Close Auto Right Down Figure 38. On-site toggle switch positions for all KTD-125 units 1040823A / June 2003... -
Page 34: Appendix C. Auxiliary Power Outlet (Ktd-125/125P)
Appendix KTD-125/127 PTZ Receivers User Manual Zoom Focus Iris Tilt ▼ ▼ ▼ ▼ ▼ ▼ ► Near Open Manual Left ► Down Close Auto Right Down Figure 39. On-site toggle switch positions for KTD-127 units C. A (KTD- PPENDIX... - Page 35 KTD-125/127 PTZ Receivers User Manual Appendix Therefore, for address 209, you would use switches 1 (1), 5 (16), 7 (64), and 8 (128). (See Figure A1) Figure A1. Zone address 209 (1 + 16 + 64 + 128) 1040823A / June 2003...
-
Page 36: Troubleshooting
Troubleshooting KTD-125/127 PTZ Receivers User Manual ROUBLESHOOTING Diagnostic check: Use the toggle switches on the main relay board to confirm that you have control of the camera from the receiver on. • If YES, then check your RS422 connections from the keyboard to the receiver.