Cisco STA1520 Quick Reference Manual

IMPORTANT SAFETY INSTRUCTIONS

Notice to Installers

The servicing instructions in this notice are for use by qualifi ed service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that
contained in the operating instructions, unless you are qualifi ed to do so.
Note to System Installer
For this apparatus, the coaxial cable shield/screen shall be
grounded as close as practical to the point of entry of the cable
into the building.For products sold in the US and Canada, this
reminder is provided to call the system installer's attention to
Article 820-93 and Article 820-100 of the NEC (or Canadian
Electrical Code Part 1), which provides guidelines for proper
grounding of the coaxial cable shield.
This symbol is intended to alert you that uninsulated voltage
within this product may have sufficient magnitude to cause
electric shock.Therefore, it is dangerous to make any kind of
contact with any inside part of this product.
Ce symbole a pour but d'alerter toute personne qu'un contact
avec une pièce interne de ce produit, sous tension et non isolée,
pourrait être suffisant pour provoquer un choc électrique. Il est
donc dangereux d'être en contact avec toute pièce interne de
ce produit.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifi ers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding-type plug has two blades and a
third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fi t into your outlet, consult an electrician for replacement of the obsolete
outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specifi ed by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specifi ed by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has
been damaged in any way, such as a power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.

Power Source Warning

A label on this product indicates the correct power source for this product. Operate this product only from an electrical
outlet with the voltage and frequency indicated on the product label. If you are uncertain of the type of power supply
to your home or business, consult your service provider or your local power company.
The AC inlet on the unit must remain accessible and operable at all times.

Ground the Product

WARNING: Avoid electric shock and fi re hazard! Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A
grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong
is provided for your safety. If the provided plug does not fi t into your outlet, consult an electrician for
replacement of the obsolete outlet.
Outdoor Grounding System
If this product connects to an outdoor antenna or cable system, be sure the antenna or cable system is grounded
(earthed). This provides some protection against voltage surges and built-up static charges.
Article 810 of the National Electric Code (NEC) ANSI/NFPA No. 70-1990, provides the following information:
• Grounding of the mast and supporting structure
• Grounding the lead-in wire to an antenna discharge unit
• Size of the grounding conductors
• Location of the antenna-discharge unit
• Connection to grounding electrodes
• Requirements for the grounding electrodes (see the following antenna grounding diagram as recommended by
NEC ANSI/NFPA 70)
WARNING: Avoid electric shock and fi re hazard! Do not locate an outside antenna system in the
vicinity of overhead power lines or power circuits. Touching power lines or circuits might be fatal.
CAUTION: To reduce the risk of electric shock, do not remove cover (or back).
No user-serviceable parts inside. Refer servicing to qualified service personnel.
WARNING
TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
This symbol is intended to alert you of the presence of important operating
and maintenance (servicing) instructions in the literature accompanying this
product.
Ce symbole a pour but de vous avertir qu'une documentation importante
sur le fonctionnement et l'entretien accompagne ce produit.
20080814_Installer 820
Protect the Product from Lightning
In addition to disconnecting the AC power from the wall outlet, disconnect the signal inputs.
Verify the Power Source from the On/Off Power Light
When the on/off power light is not illuminated, the apparatus may still be connected to the power source. The light may
go out when the apparatus is turned off, regardless of whether it is still plugged into an AC power source.
Eliminate AC Mains Overloads
WARNING: Avoid electric shock and fi re hazard! Do not overload AC mains, outlets, extension
cords, or integral convenience receptacles. For products that require battery power or other power sources
to operate them, refer to the operating instructions for those products.
Provide Ventilation and Select a Location
• Remove all packaging material before applying power to the product.
• Do not place this apparatus on a bed, sofa, rug, or similar surface.
• Do not place this apparatus on an unstable surface.
• Do not install this apparatus in an enclosure, such as a bookcase or rack, unless the installation provides proper
ventilation.
• Do not place entertainment devices (such as VCRs or DVDs), lamps, books, vases with liquids, or other objects
on top of this product.
• Do not block ventilation openings.
Protect from Exposure to Moisture and Foreign Objects
WARNING: Avoid electric shock and fi re hazard! Do not expose this product to liquids, rain,
or moisture. Do not expose this product to dripping or splashing liquids, rain, or moisture. Objects
fi lled with liquids, such as vases, should not be placed on this apparatus.
WARNING: Avoid electric shock and fi re hazard! Unplug this product before cleaning. Do not
use a liquid cleaner or an aerosol cleaner. Do not use a magnetic/static cleaning device (dust remover)
to clean this product.
WARNING: Avoid electric shock and fi re hazard! Never push objects through the openings in
this product. Foreign objects can cause electrical shorts that can result in electric shock or fi re.

Cisco STA1520 Tuning Adapter

RNG100
Service Warnings
WARNING:
Avoid electric shock! Do not open the cover of this product. Opening or removing
the cover may expose you to dangerous voltages. If you open the cover, your warranty will be void. This
product contains no user-serviceable parts.
Check Product Safety
Upon completion of any service or repairs to this product, the service technician must perform safety checks to
determine that this product is in proper operating condition.
Protect the Product When Moving It
Always disconnect the power source when moving the apparatus or connecting or disconnecting cables.
20081112_Cable_Safety
Disclaimer
Cisco Systems, Inc. assumes no responsibility for errors or omissions that may appear in this guide. We reserve the
right to change this guide at any time without notice.
United States FCC Compliance
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against such interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in
accordance with the instructions, it may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the service provider or an experienced radio/television technician for help.
Any changes or modifi cations not expressly approved by Cisco Systems, Inc., could void the user's authority to
operate the equipment.
The information shown in the FCC Declaration of Conformity paragraph below is a requirement of the FCC and is intended
to supply you with information regarding the FCC approval of this device. The phone numbers listed are for FCC-related
questions only and not intended for questions regarding the connection or operation for this device. Please contact your
service provider for any questions you may have regarding the operation or installation of this device.
Quick Reference Guide
POWER DATA REMOTE STA1520
Declaration of Conformity
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1) the device
may not cause harmful interference, and 2) the device must accept any interference received, including interference
that may cause undesired operation.
Cisco STA1520 Tuning Adapter
Model: STA1520
Manufactured by: Cisco Systems, Inc.
5030 Sugarloaf Parkway
Lawrenceville, Georgia 30044 USA
Telephone: 678 277-1120
Canada EMI Regulation
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la class B est conforme à la norme NMB-003 du Canada.
Cisco Systems, Inc.
5030 Sugarloaf Parkway, Box 465447
Lawrenceville, GA 30042
Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affi liates in the U.S. and other countries. A listing
of Cisco's trademarks can be found at www.cisco.com/go/trademarks.
CableCARD is a trademark of Cable Television Laboratories, Inc.
Other third party trademarks mentioned are the property of their respective owners.
The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1007R)
©2008-2010, 2012 Cisco and/or its affi liates. All rights reserved.
September 2012 Printed in United States of America
20081121 FCC Standard
678.277.1120
www.cisco.com
Part Number 4024567 Rev D