Yamaha TSX-10 Owner's Manual page 8

Never plug the AC power cord into the wall outlet until all connections are
completed.
Follow the steps as shown below to connect the system using the supplied cables and accessories.
Right speaker
c_--___-_-___
\
NX-TSPO ;
--
NX-TSlO
1
:
_--__-----
Indoor
FM antenna
AM loop antenna
cl
II 2 3
3
To wall outlet
I I
'I '
Left speaker
c__--__--__--
I
\
I
NX-TSPO
I
I NX-TSlO
I
I
c--_---__---_
:
1
Connecting speakers
Connect the speakers to the SPEAKERS terminals of the main unit by using the speaker cables. Make sure that the
polarity of the speaker cables is correct, i.e. the + and - markings are observed. If these cables are reversed, the sound will
be unnatural and lack bass.
On the main unit On the speakers (NX-TSZO)
Red: positive (+)
Black: negative (-)
'ress the tab.
@ Remove approx. 10 mm
/ /
(3/V) of insulation from
On the speakers
(NX-TSIO)
each of the speaker
cables and insert the bare
iire into the terminal.
@ Release the tab and
secure the cable.
Jnscrew the knob.
@ Remove approx. 10 mm
(3%') of insulation from
each of the speaker
cables and insert the bare
dire into the terminal.
@ Tighten the knob to
secure the cable.
Caution
Do not let the bare speaker wires touch each
other as this could damage the main unit and/or
speakers.
6
GETTING STARTED
Never plug the AC power cord into the wall outlet until all connections are
completed.
Follow the steps as shown below to connect the system using the supplied cables and accessories.
Right speaker
,..
-
- -
- - - - -
-
-
- - \
NX-TS20
NX·TS10
1
Connecting speakers
Indoor
FM antenna
Q
1
B
AM loop antenna
o
Left speaker
NX-TS20
NX·TS10 :
I .... '
Connect the speakers to the SPEAKERS terminals of the main unit by using the speaker cables. Make sure that the
polarity of the speaker cables is correct, i.e. the
+
and - markings are observed. If these cables are reversed, the sound will
be unnatural and lack bass.
On the main unit
On the speakers (NX-1520)
Caution
Do not let the bare speaker wires touch each
other as this could damage the main unit and/or
speakers.
On the speakers
(NX-TS10)
6
Red: positive (+)
Black: negative (-)
'ress the tab.
®
Remove approx. 10 mm
(3/8") of insulation from
each of the speaker
cables and insert the bare
,ire into the terminal.
@ Release the tab and
secure the cable.
Red: positive
(+)
Black: negative (-)
Jnscrew the knob.
®
Remove approx. 10 mm
(3/8") of insulation from
each of the speaker
cables and insert the bare
,ire into the terminal.
@ Tighten the knob to
secure the cable.
GETTING STARTED
Never plug the AC power cord into the wall outlet until all connections are
completed.
Follow the steps as shown below to connect the system using the supplied cables and accessories.
Right speaker
,..
-
- -
- - - - -
-
-
- - \
NX-TS20
NX·TS10
1
Connecting speakers
Indoor
FM antenna
Q
1
B
AM loop antenna
o
Left speaker
NX-TS20
NX·TS10 :
I .... '
Connect the speakers to the SPEAKERS terminals of the main unit by using the speaker cables. Make sure that the
polarity of the speaker cables is correct, i.e. the
+
and - markings are observed. If these cables are reversed, the sound will
be unnatural and lack bass.
On the main unit
On the speakers (NX-1520)
Caution
Do not let the bare speaker wires touch each
other as this could damage the main unit and/or
speakers.
On the speakers
(NX-TS10)
6
Red: positive (+)
Black: negative (-)
'ress the tab.
®
Remove approx. 10 mm
(3/8") of insulation from
each of the speaker
cables and insert the bare
,ire into the terminal.
@ Release the tab and
secure the cable.
Red: positive
(+)
Black: negative (-)
Jnscrew the knob.
®
Remove approx. 10 mm
(3/8") of insulation from
each of the speaker
cables and insert the bare
,ire into the terminal.
@ Tighten the knob to
secure the cable.