Yamaha TSX-10 Owner's Manual page 14

You must set the clock before you use the timer functions.
The clock is based on the 12-hour system for U.S.A. and
Canada models, and the 24-hour system for Europe, U.K.,
Australia and China models.
HOUR - HOUR +
You can adjust the brightness of the display not only
when the unit is turned on but also in the standby mode.
The adjustment can be made individually.
TIME ADJ DISPLAY
MIN -
MIN +
1
While the power is on, press DISPLAY to display
the time.
2
While holding TIME ADJ, press HOUR + to set the
hour.
l
If you want to move the time in the reverse
direction, press HOUR - while holding TIME
ADJ.
3
While holding TIME ADJ, press MIN + to set the
minutes.
l
If you want to move the time in the reverse
direction, press MIN - while holding TIME ADJ.
To display the clock
Press DISPLAY.
First "Clock Time" appears and then the current time is
displayed for about 8 seconds. Then the normal display
returns.
Note
l
In the event of a power failure or when the AC power cord is
disconnected for more than five minutes, "Set Clock" may
appear on the display instead of the current time. In
that case,
you need to reset the clock.
DISPLAY VOLUME
Press and hold DISPLAY for about two seconds so that
"Dimmer +O" appears on the display. While holding
DISPLAY, turn VOLUME clockwise to increase or
counterclockwise to decrease brightness.
Control Range: +O to -6 (Preset value: &O)
Note
l
During the standby mode, the display is not as bright as the
one when the
unit is on.
You
can further decrease the
brightness in the standby mode so that the light does not
disturb in a dark ambience.
12
GETTING STARTED
You must set the clock before you use the timer functions.
The clock is based on the l2-hour system for U.S.A. and
Canada models, and the 24-hour system for Europe, U.K.,
Australia and China models.
HOUR- HOUR+
You can adjust the brightness of the display not only
when the unit is turned on
but
also in the standby mode.
The adjustment can be made individually.
TIME ADJ DISPLAY MIN- MIN +
DISPLAY
VOLUME
1
While the power is on, press DISPLAY to display
the time.
2
While holding TIME ADJ, press HOUR + to set the
hour.
• If you want to move the time in the reverse
direction, press HOUR - while holding TIME
ADJ.
3
While holding TIME ADJ, press MIN + to set the
minutes.
• If you want to move the time in the reverse
direction, press MIN - while holding TIME ADJ.
To
display
the clock
Press DISPLAY.
First "Clock Time" appears and then the current time is
displayed for about 8 seconds. Then the normal display
returns.
Note
• In the event of a power failure or when the AC power cord is
disconnected for more than five minutes, "Set Clock" may
appear on the display instead of the current time. In that case,
you need to reset the clock.
12
Press and hold DISPLAY for about two seconds so that
"Dimmer ±O" appears on the display. While holding
DISPLAY, turn VOLUME clockwise to increase or
counterclockwise to decrease bri.e;htness.
Control Range: ±O to
-6
(Preset value: ±O)
Note
• During the standby mode, the display is not as bright as the
one when the unit is on. You can further decrease the
brightness in the standby mode so that the light does not
disturb in a dark ambience.
GETTING STARTED
You must set the clock before you use the timer functions.
The clock is based on the l2-hour system for U.S.A. and
Canada models, and the 24-hour system for Europe, U.K.,
Australia and China models.
HOUR- HOUR+
You can adjust the brightness of the display not only
when the unit is turned on
but
also in the standby mode.
The adjustment can be made individually.
TIME ADJ DISPLAY MIN- MIN +
DISPLAY
VOLUME
1
While the power is on, press DISPLAY to display
the time.
2
While holding TIME ADJ, press HOUR + to set the
hour.
• If you want to move the time in the reverse
direction, press HOUR - while holding TIME
ADJ.
3
While holding TIME ADJ, press MIN + to set the
minutes.
• If you want to move the time in the reverse
direction, press MIN - while holding TIME ADJ.
To
display
the clock
Press DISPLAY.
First "Clock Time" appears and then the current time is
displayed for about 8 seconds. Then the normal display
returns.
Note
• In the event of a power failure or when the AC power cord is
disconnected for more than five minutes, "Set Clock" may
appear on the display instead of the current time. In that case,
you need to reset the clock.
12
Press and hold DISPLAY for about two seconds so that
"Dimmer ±O" appears on the display. While holding
DISPLAY, turn VOLUME clockwise to increase or
counterclockwise to decrease bri.e;htness.
Control Range: ±O to
-6
(Preset value: ±O)
Note
• During the standby mode, the display is not as bright as the
one when the unit is on. You can further decrease the
brightness in the standby mode so that the light does not
disturb in a dark ambience.