Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Baumatic BE600GL
Summary of Contents for Baumatic BE600GL
- Page 1 BE600GL/BE700GL/ BE900GL Cooker Hood...
- Page 2 User Manual for your Baumatic BE600GL Cooker Hood 60 cm Glass cooker hood in stainless steel BE700GL Cooker Hood 70 cm Glass cooker hood in stainless steel BE900GL Cooker Hood 90 cm Glass cooker hood in stainless steel NOTE : This User Instruction Manual contains important information, including safety &...
-
Page 3: Table Of Contents
Contents Page Environmental note IMPORTANT SAFETY INFORMATION 5 – 7 Specifications of your BE600GL cooker hood Specifications of your BE700GL cooker hood Specifications of your BE900GL cooker hood Using your cooker hood 11 - 12 Before first use To use your cooker hood... -
Page 4: Environmental Note
ENVIRONMENTAL NOTE Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be undertaken by a competent person. -
Page 5: Important Safety Information
IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Advice Line. - Page 6 o When installed between adjoining wall cabinets, the cabinets must not overhang the hob. o The edges of the cooker hood are sharp – be mindful of this as you handle your appliance, especially during installation and cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTERS! o If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the sealed or balanced flue type.
- Page 7 to observe the fire safety advice contained in this instruction booklet. o Remember that when in extraction mode, your cooker hood is removing air from your room. Ensure that proper ventilation measures are being observed. o Note that it removes odours from your room, not steam. o Warning - Always ensure that the cooker hood been...
-
Page 8: Specifications Of Your Be600Gl Cooker Hood
Specifications of your BE600GL cooker hood PRODUCT DIMENSIONS: Height: 600 mm – 980 mm Width: 600 mm Depth: 405 mm DIMENSIONS OF CHIMNEY SECTION: 297 mm x 265 mm Your stainless steel cooker hood is fitted with: o Integrated axial motor... -
Page 9: Specifications Of Your Be700Gl Cooker Hood
Specifications of your BE700GL cooker hood PRODUCT DIMENSIONS: Height: 600 mm – 950 mm Width: 700 mm Depth: 405 mm DIMENSIONS OF CHIMNEY SECTION: 297 mm x 265 mm Your stainless steel cooker hood is fitted with: o Integrated axial motor o Electronic push button control operation o 3 Speeds o 1 Washable aluminium grease filter... -
Page 10: Specifications Of Your Be900Gl Cooker Hood
Specifications of your BE900GL cooker hood PRODUCT DIMENSIONS: Height: 600 mm – 980 mm Width: 900 mm Depth: 405 mm DIMENSIONS OF CHIMNEY SECTION: 297 mm x 265 mm Your stainless steel cooker hood is fitted with: o Integrated axial motor o Electronic push button control operation o 3 Speeds o 1 Washable aluminium grease filter... -
Page 11: Using Your Cooker Hood
Make sure that it has been installed by a suitably qualified person, information contained Baumatic’s installation instructions. o Find the control panel, which is located at the front of the canopy. o There are several buttons on the control panel, which perform separate functions. -
Page 12: Cleaning Your Cooker Hood
IMPORTANT: IDEALLY YOU SHOULD SWITCH ON YOUR HOOD TEN MINUTES BEFORE YOU START TO COOK, OR AT THE VERY LEAST WHEN YOU BEGIN COOKING. YOU SHOULD ALSO RUN YOUR HOOD FOR TEN MINUTES AFTER YOU HAVE FINISHED COOKING. Cleaning your cooker hood IMPORTANT: BEFORE CLEANING, ALWAYS ENSURE THAT YOU HAVE SWITCHED YOUR COOKER HOOD OFF AT THE OMNI-POLAR SWITCH, SET AT THE... -
Page 13: The Grease Filter
The grease filter o Your cooker hood includes a grease filter which helps to absorb grease particles to protect your kitchen and furniture from greasy residues. o This aluminium filter may become flammable if it becomes saturated with this greasy residue. o To prevent this fire hazard, the filter should be cleaned regularly. - Page 14 o First remove the grease filter by pulling down on the handle and then pulling it away from the cooker hood. o Soak the grease filter in hot water and washing up liquid for at least 5 minutes (or longer if the grease build up is severe). o Rinse it off thoroughly with hot water.
-
Page 15: Changing A Light Bulb
Changing a light bulb IMPORTANT: BEFORE ATTEMPTING TO CHANGE A LIGHT BULB, YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE COOKER HOOD FROM YOUR MAINS SUPPLY. o Remove grease filter described on pages 13 - 14). o Prior to touching the light bulbs ensure that they have cooled down. -
Page 16: Fitting The Carbon Filters
Fitting the carbon filters If the appliance is being used to be used in recirculation mode then it is necessary to fit carbon filters. This will help to absorb unpleasant odours caused by cooking. IMPORTANT: BEFORE ATTEMPTING TO FIT OR REMOVE THE CARBON FILTERS, YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE COOKER HOOD FROM YOUR MAINS SUPPLY. -
Page 17: Installation
Installation IMPORTANT: Before installation and usage read all the instructions and make sure that the voltage (V) and the frequency (Hz) indicated on the rating plate are exactly the same as the voltage and frequency in your home. The rating plate can be found behind the grease filter. -
Page 18: Before Beginning Installation
o As the colours of the wires in the appliance’s mains lead may not correspond with the coloured markings identifying the terminals in your spur box, please proceed as follows: o The blue wire must be connected to the terminal marked “N” (neutral), or coloured black. -
Page 19: Attaching The Glass Canopy
o Rawl plugs are provided to secure the hood to most types of walls and ceilings. However a qualified technician must verify the suitability of the materials, in accordance with the type of wall and ceiling. The wall and ceiling must be strong enough to take the weight of the hood. -
Page 20: Installing Your Cooker Hood
Please note that the styles of cooker hood shown in the line drawings in the following pages are sometimes different to the shape of the BE600GL, BE700GL and BE900GL. However the installation method shown is correct and MUST be followed. - Page 21 2a) The support screw holes are indicated by figure A in this drawing and the anchoring screw holes are indicated by figure B. 3) Using a drill bit with an 8 mm diameter, make holes in the wall on the positions that you have marked in step 4) Insert rawl plugs into all of the holes that you have drilled.
- Page 22 6) Hang the hood onto the support screws. 7) Fully tighten the support screws (A) and then screw the anchoring screws (B) through the relevant holes in the cooker hood. Tighten the anchoring screws fully into the wall.
-
Page 23: Connecting To External Ducting
Connecting to external ducting 8) Connect the coupling to the top of the cooker hood, and then connect a 125 mm ducting hose to the coupling (please note that the ducting hose is not supplied with the appliance). o The other end of the ducting hose should be connected to a discharge outlet that is suitable for cooking vapours. - Page 24 10) Lift chimney section (D) upwards until it reaches the ceiling. You must ensure that it is perpendicular to the hood. o Mark the side measurements of both sides of chimney section (D) on the wall with a pencil and then remove chimney section (D).
- Page 25 12) Using an 8 mm drill bit, drill out two holes on the pencil markings that you made in step 11. Insert rawl plugs into the holes and then use a screwdriver to secure the fixing bracket to the wall. o Refit chimney section (C) to the hood and fix it onto the hood using the two screws that are supplied.
-
Page 26: Completing The Installation
Completing the installation If you are setting the appliance to recirculation mode, then you should now fit the two carbon filters. See the “Fitting the carbon filters” section on page 16. The electrical connection must correspond to the electrical requirement noted on the rating plate, which is placed inside the cooker hood. -
Page 27: Troubleshooting
Troubleshooting IMPORTANT: If your cooker hood appears not to be operating properly, before contacting the Customer Care Department, please refer to the checklist below. My cooker hood will not start. o Check that the hood is connected to the electricity supply o Check that the fan speed control is set correctly. - Page 28 Or any installation other than the one specified by Baumatic Ltd. has been completed. Please refer to the conditions of guarantee that appear on the warranty card that you receive with the appliance.
-
Page 29: Baumatic Consumables
BC005 Stainless Steel Cleaner and Protector (250 ml) o BC007 E-Cloth – General Purpose Cloth o BC008 Microwave Cover To order a Baumatic consumable product please call 0123 5437 244 and quote the product code. You can also order online from eshop.baumatic.co.uk... -
Page 30: Contact Details
United Kingdom Baumatic Ltd., Baumatic Buildings, Czech Republic 6 Bennet Road, Baumatic CR spol s.r.o. Reading, Berkshire Lípovà 665 RG2 0QX 460 01 Liberec 4 United Kingdom Czech Republic Sales Telephone +420 483 577 200 (0118) 933 6900 Sales Fax www.baumatic.cz...