1 Preparation job before configuration 1.1 Learn your router version and feature 1) H685 series contains different version and option feature. Please learn it before using it. H685 series defines the model as follows, Notes: please be informed the following features are option. Please indicate with your orders.
If you find your signal strength is not good, please contact us for high gain antenna. Chapter 2 2 Hardware Installation This chapter mainly describes the appearance, model and function of H685 series and how to install and set the configurations. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com...
Page 8
There is label printing on the back of the router case. Please refer it to connect the correct antennas. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Attention: Do not install H685 series or connect/disconnect its cable when it is power on. 2.4 SIM/UIM card installed If your router has SIM/UIM card protector, please remove it, insert the sim card correctly, and fix the protector.
Page 11
GND. Reset After giving the device a 1 sec low level, it will reboot.3 seconds, the device will restore factory settings General Purpose DIO0 General Purpose DIO1 Not connect E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Please connect the antenna after you successfully connect to the cable. And then insert the valid SIM/UIM card and provide the power to the H685 series via the cable. After provide the power to H685, if the SYS LED starts to blink in a few seconds, that means the system start-up is normal;...
Page 13
System set-up failure seconds blink Data transmission in Ethernet Ethernet connection abnormal Ethernet is connected VPN tunnel set-up VPN tunnel set-up failure or unactivated CELL Access to the Internet WIFI Enable Disable E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
3. How to config web 3.1 Overview H685 series routers with built-in WEB interface configuration, management and debugging tools, user should configuration the parameters first; and it could be altered the parameters flexibility and software upgrades and simple testing. User can set up and manage the parameters of the router on its interface, detail step are bellow: 3.2 How to log into the Router...
Page 15
Set the PC IP as 192.168.8.xxx (xxx = 2~254), subnet mask: 255.255.255.0, default gateway: 192.168.8.1, primary DNS: 192.168.8.1. Way 2) DHCP Choose “Obtain an IP address automatically” and “Obtain DNS server address automatically”. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 16
This information means the connection is work. This information means the connection is failure. If so, please check the network cable connection and IP address setting, and can refer to Chapter 4.9. 3.2.2 Log into Router E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 17
Type User Name “admin” and Password “admin” in the pop-up Login Window, and then press the “Apply” button. If you type into the correct User Name and Password, you will get the access into the Router’s Web Management Page. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
H685 User Manual 3.3 How to configure web 3.3.1 Main Menu as below Picture E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
The wireless apcli interface is treated as WAN port and the wireless ap interface and the Ethernet ports are LAN ports. Network Address Translation Normally and default we select “Gateway mode”, and keep all other parameters as default. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Notes: the Cell Modem Type was marked on the back of the router. For example, it shows the following picture. H685 is the router series name, H685w-W-RS232 is the part number name. And the EM820w Cell Modem is the Cell Modem name. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 21
Notes: If you don’t replace any cellular module or not do the “Load Default to factory”, please skip this step and jump to next settings. At “Cell Modem”, please select “AUTO_DETECT”, and click “Apply” button. The router will automatically detect the module modem. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 22
Advance Parameter Groups Click Advance Parameter Groups, Cell Modem Parameters Groups expand. Define one APN Group to fit your network and sim card. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 23
Password: fill in the related parameters. Get this parameter from the Sim Card Provider or Carrier; If yours has no user name, please input out default value, otherwise the router may not dialup. Our default value for GSM/WCDMA/LTE is “wap”, and for CDMA/EVDO is “card”. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 24
10, the router will get LCP check every 10 seconds. Other parameters: user can disable or enable or define it. Warmly Reminding: do not forget to click Apply button after setting. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
The sleep time is 5 minutes. After 5 minutes, H685 Router resume to cycle the checking. 3.3.3.3 AP Client mode (WiFi Client) Set H685 as an AP client, H685 will connect the upper WiFi router or WiFi AP. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 26
SSID: input the WiFi router’s SSID Security Mode: choose correct one to match the WiFi router/AP you want to connect. Encryption Type: choose correct one to match the WiFi router/AP you want to connect. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 27
Here please select the right channel the same with the upper WiFi Router/AP you want to connect. Then choose the same Channel in H685 router as follows, Step4) Internet Settings – WAN E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Notes: you may not see the WAN RJ45 connection status. But it will flash to fresh the status every 30 seconds. Or you can manually flash to fresh. Step 2) H685 web – Operation Mode, choose “Gateway” mode E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 29
Set the Idle Time. PPPoE will be offline if the set idle time has no data transmission. Manual: need manually dialup. Click “Apply” button. Step 4) H685 web – Status, it display the WAN IP once the PPPoE is online. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
30 seconds. Or you can manually flash to fresh. Step 2) H685 web – Operation Mode, choose “Gateway” mode Step 3) H685 web – Internet Settings – WAN – WAN Connection Type, choose “STATIC (fixed IP)” E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
H685 web – Status, it display the WAN IP once the STATIC (fixed IP) is online. 3.3.3.6 WAN – DHCP (Auto config) Set H685 WAN via DHCP (Auto config), H685 will connect the upper router via DHCP. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 32
H685 web – Internet Settings – WAN – WAN Connection Type, choose “DHCP (Auto config)” WAN Connection Type: choose “DHCP (Auto config)” Click “Apply” button. Step 4) H685 web – Status, it display the WAN IP once the DHCP (Auto config) is online. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Setting the LAN parameters, include IP address, sub mask, VLAN, DHCP, etc. 3.3.4.1 Router Gateway IP Default, the Router LAN IP is 192.168.8.1. If users want to modify it, please change the related parameters. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
End IP Address: for DHCP end IP Default Gateway: manually change it after you modify the IP Address. 3.3.4.2 MAC binding H685 Router supports 3 groups of MAC Binding. The parameter value format is as followed picture. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
This section mainly introduces what is Routing Table and how to configure static router. Routing Table This page shows the key routing table of this router. New Static Router This page is about how to set static routing function of the router. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
3.3.7 VPN Notes: the following VPN configuration manual may be out of date. We update the IPSec and PPTP configuration in another manual. Please refer to manual of “H685_H685_VPN_Usermanual_Eng.pdf”. 3.3.7.1 IPSEC E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 38
(111.vpn1.com). if you want to build a point-to-point channel, the IPsec name have written DEV+equipment ID+name (DEV281250D52F2A1452.vpn1.com), and make sure both the client and server are inputing Client equipment ID. You can find H685’s ID in the Status interface. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 39
IPsec name have to be written as DEV+equipment ID+name(DEV281250D52F2A1452.vpn1.com), and make sure both the client and server are inputing Client equipment ID. You can find H685’s ID in the Status interface. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 40
1 set security-association lifetime kilobytes 536870912 set security-association lifetime seconds 43200 set transform-set vpnset set isakmp-profile jordan reverse-route crypto map COREVPN 26 ipsec-isakmp dynamic jordan E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
1) If the PPTP cannot through between client and server, please check if the MPPE configuration is matched with PPTP server or not. 2) Normally PPTP server has route for 192.168.1.1/24 or 192.168.0.1/24. Please check the PPTP E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
192.168.8.0/24 if your H820 router is with IP 192.168.8.1 3.3.7.3 L2TP L2TP feature works as Client only. 3.3.7.4 Tunnel Tunnel Feature The H685 Tunnel feature supports two GRE. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
H685 User Manual IP Tunnel Feature 3.3.8 DTU Settings (Serial to Cellular Gateway Feature) Notes: this feature is for H685 with DTU option only. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 44
Send heart beat: open or close heart beat. heart beat interval time: set interval time to send each heart beat heart beat information: define the content of heart beat E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Add id string to head: add an ID string in the data or heartbeat. 3.3.9 SMS/Voice Control Notes: this feature is for H685 with SMS/Voice option only. 3.3.9.1 SMS Step 1) click “SMS/Voice” Step 2) Activate the SMS feature E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 46
Telephone number: Sender’s phone number input. Totally can input 10 groups. Number 1….10: input the dedicated sender’s phone number. Do not forget to Tick “SMS” Step 3) Define the SMS command E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 47
2) Try to add zone code or country code if the command cannot get working. For example, we set the number 13798257916, and if the command cannot work, please try to put the country code 86 as followed picture. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 48
Use the cell phone 13798257916 to send “up” to the router’s SIM Card Number, the router will receive the “up” command, and it will be online. And in the System Log, we shall find a info as following marks. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
H685 User Manual 3.3.9.2 Voice Notes: This feature may not work due to network compatibility or module modem. Step 1) enable voice feature Step 2) set the dedicated phone number for voice control E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
2 control to be offline. 3.3.9.3 Alarm via SMS With this feature, the Router will send SMS to pre-defined phone number for warning and alarm. Step 1) enable Alarm feature E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Router keeps checking signal quality every 20s, if continuous 8 times are with signal quality better than 0, the alarm feature will be unlocked, then the alarm feature starts work again. 3.3.10 Link Backup (Route Redundancy) E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 52
If set it as YES, WAN1/WAN2/WAN3 use same check IP or domain name from ALL WAN Check Method. If set is as NO, users need set WAN1/WAN2/WAN3 live check IP or domain name separately. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 53
With this configuration, the router will work at DHCP mainly, and if DHCP is failed, it switches to cellular automatically after some time. And it will automatically switch to DHCP when DHCP is E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 54
With this configuration, the router will work at cellular mainly, and if cellular is failed, it switches to DHCP automatically after some time. And it will automatically switch to cellular when cellular is fixed. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 55
LAN RJ45 cable WAN or WiFi client mode if cellular network is failed. Notes: for route fail over feature, please first make the main network and backup network both work before activate the fail over feature. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Sock type: tcp or udp Server: fill in the correct destination server IP or domain name Server port: fill in the correct destination server port GPS to Serial Settings E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
serial databits: 7/8 for choice serial stopbits: 1/2 for choice serial flow control: none/hardware/software for choice 3.3.12 WiFi Wireless Settings Notes: WiFi Feature is H685 with WiFi only 3.3.12.1 Basic Wireless Settings E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Multiple SSID1: H685 Router supports multiple SSID 8 groups totally. Broadcast Network Name (SSID): Enable or Disable SSID broadcast. BSSID: indicates the MAC of WiFi Frequency (Channel): current working frequency and channel. 3.3.12.2 WiFi Advanced Settings E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Access policy: setting the MAC list for access or deny. Disable: close the Access Policy. Allow: allow the assigned MAC enable to use WiFi Reject: refuse the assigned MAC enable to use WiFi 3.3.12.4 WDS 3.3.12.5 WPS 3.3.12.6 Station List E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Action: choose Accept or Drop Comment: input comment here Current MAC/IP/Port filtering rules in system It display the configured rules in this table. 3.3.13.2 Port Forwarding (Virtual Server Settings)(NAT/NAPT) E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
IP address: fill the IP address of forwarding. The first blank is for local IP address, the second blank is for port. Port Range: fill the Port of forwarding. 3.3.13.3 DMZ Host E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Except TCP port: disable or enable for TCP port Note: When DMZ host is settled, the computer is completely exposed to the external network; the firewall will not influence this host. 3.3.13.4 System Security E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Flood and SPI Firewall (Stateful Packet Inspection). 3.3.13.5 Content Filter Settings You can setup Content Fillter to restrict the improper content access, including Webs Content Settings, URL filter and Host Filter. Proxy/Java/Activex Filter E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 67
H685 User Manual Support Proxy, Java, ActiveX filter. Web URL Filter Fill in the URL for filter. Web Host Filter E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Select Web display language. Default is English. Can OEM other languages. Administrator Settings Select Web display language. Default is English. Can OEM other languages. WatchDog Web Management Port Settings E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 69
NTP Settings DDNS Settings Dynamic DNS Provider: choose the right DNS server provider. Supported server list. Account: fill in account info. Password: fill in password info. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
3.3.14.1.1 Router web port Please input the web port of the router. Normally we use 80 or 10000. Please re-power the router after changing the port number. 3.3.14.1.2 Language, password and NTP settings E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
H685 User Manual Select Language Administrator Settings. The default both are admin. NTP Settings 3.3.14.1.3 DDNS settings Dynamic DNS Provider: choose the right DNS server provider. Supported server list. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
“Load Default”. Or re-configure the H685 after “Load Default” For some version of firmware, it requires uploading bootloader also. Please operate at the following picture. But most of time it no need do this step unless E-Lins guide or inform you to upload bootloader.
This is not recommended in order to avoid the loss of important parameter 3.3.14.4 System Command Input related command at command area. Click “Apply” button to execute. Then click “Refresh” button. The blank area will display infos. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
H685 User Manual 3.3.14.5 System Log Remote System Log Settings H685 Router support export the sys log into remote server. It requires sys log server tool. Download link: http://www. szelins.com/download/tool/SyslogWatcherSetup-4.2.0-win32_1.rar E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
H685 User Manual Display the statistics information of system flow. 3.3.14.7 Reboot E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 78
Reboot AT Time Settings Users can define the exact time to reboot for everyday. Reboot AT Time Settings Users can set timer to reboot. Reboot AT Time Settings E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
H685 User Manual Manually click “Reboot” button to reboot immediately. 3.3.14.8 Status E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 80
Software Version: software version reveals the status of software update. Hardware Version: indicates the hardware version System Up Time: this time directly reveals router working hours Operation Mode: indicates the router working mode Cell Network Info E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 81
Secondary Domain Name Server: indicates the secondary DNS of set or from ISP. MAC Address: indicates the WAN MAC address Local Network Local IP address: the H685 Router LAN IP MAC Address: the LAN MAC address E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Soft tool download link: http://www. szelins.com/download/tool/SNMP-JManager-v1.0.rar H685 router web page – Internet Settings – SNMP Fill in related parameters in the screen like follows, SNMP Active: tick it to active SNMP feature. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 83
Here list the most important OID: 1.3.6.1.4.1.2021.255.4.1.2.9.103.101.116.95.109.111.100.101.109.1 (read module modem model) 1.3.6.1.4.1.2021.255.4.1.2.10.103.101.116.95.117.112.116.105.109.101.1 (system running time) 1.3.6.1.4.1.2021.255.4.1.2.12.103.101.116.95.109.101.109.95.102.114.101.101.1 (memory capacity) 1.3.6.1.4.1.2021.255.4.1.2.15.103.101.116.95.99.101.108.108.95.115.116.97.116.117.115.1 (3G network status) 1.3.6.1.4.1.2021.255.4.1.2.15.103.101.116.95.108.50.116.112.95.115.116.97.116.117.115.1 (pptp status) 1.3.6.1.4.1.2021.255.4.1.2.15.103.101.116.95.112.112.116.112.95.115.116.97.116.117.115.1 (l2tp status) List client side’s picture as follows, E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
With this error, it indicates the sim card is not well touched with sim card slot. Try to check the sim card is right put. Try to scrap the sim card slot and make it clean. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Our router built-in different types of modem inside, some modem cost this. But will not affect the use. 4.7 Router shows sim card and network info, but cannot connect to internet Check the sim card is with balance or limited service by the ISP. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
2) Double check if the H685 WiFi is on. 3) Double check Device’s wireless network card IP is correct configured. Please refer to Chapter 3.2 4) Try to disable the Device’s network card, and re-enable it. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
2) Reset the H685 router. Power on router, keep press “RST” button until 12 seconds, and then release it. H685 router will automatically load default. 4.12 Cannot get Cell WAN IP H685 Router get cellular WAN IP once it’s online. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Solution: 1. Check if the power adapter connector is loose from the router. 2. Try to replace a power adapter. H685 series router uses 9V1A or 9V2A or 12V1A or 12V1A or 12V2A power adapter with 2.5mm connector 3. Router hardware defeated. Send back to factory for check or repair.
27.38.14.223:80 if can be okay. If no okay, it means the ISP/Carrier blocks the 10000 port. Then check with your ISP/Carrier which ports are open for use. Then re-try the port forwarding feature. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
H685 LAN IP from 192.168.8.1 to 192.168.1.1 or 192.168.0.1, also do not forget to manually change the H685 Default Gateway to 192.168.1.1 or 192.168.0.1 meanwhile. 3) with the following steps, normally it can solve the issue. Otherwise, please contact E-Lins Sales or Support. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com...
1. Take two H685 router. One will be WiFi server, the other will be WiFi Client. We name H685-s and H685-c 2. Connect PC with H685-s with RJ45 cable. 3. At H685-s and H685-c, make sure the DHCP service from both routers are working. At H685-s, E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 93
4. At H685-s, “Wireless Settings--Basic”, set Network Name (SSID) as “3G Router” (Here we recommend you use “3G Router” to test first) And write down the “Frequency (Channel)” and “Extension Channel”. Remember it and we shall use this value at H685-c. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 94
6. Try to connect the H685-s WiFi via your Laptop/PC. If can work, then go to step 7. 7. Connect PC with H685-c with RJ45 cable. 8. at H685-c, “Operation Mode”, choose “AP client”, and click “Apply” E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 95
9. at H685-c, “Wireless Settings—AP Client—SSID”, here input the correct one. Here the value is from the H685-s. 10. at H685-c, “Frequency (Channel)” and “Extension Channel” should be the same as H685-s E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 96
11. at H685-c, “Internet Settings--WAN”, set the WAN connection type as “DHCP (Auto config)”, and click “Apply” button. 12. Then check H685-c, “Administration--Status”, if it shows “Operation Mode” as “AP client Mode” and get “WAN IP Address”, that means the test is working. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Note: the test is simulation test to approve and show the feature. Please make it work in your real application. Here we run a TCP server tool as the GPS TCP server. Step1: configure the GPS feature of the router. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 98
And we make a DMZ or NAT for this IP and port from the local router connected to internet with IP 27.38.13.57. And in the router GPS configuration, we fill in “27.38.13.57” and port “10001”. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 99
Once the link is okay, it will show the following similar screen. If the route doesn’t get the satellite, it appears and updates the GPS module info from the router to the TCP GPS server. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
27.38.14.223:80 if can be okay. If no okay, it means the ISP blocks the 80 port. Then check with your ISP which ports are open for use. Then re-try the port forwarding feature. Step 1) make H685 router to be online. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 101
Connect the PC to H685 router LAN port via RJ45 cable. And it gets an IP 10.10.10.100. At the PC, run TCP&UDP_debug software (If you have no such software, require to get from us). E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 102
Choose the created server, and click StartServer. It will show the following windows. Step 4) here we take another PC to be as a TCP client. This PC is with internet in another network. Run TCPUDP_debug software tool, choose Client Mode, E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 103
Type: choose TCP, DestIP: fill in the H685 router’s WAN IP (here is 113.115.141.126), Port: 8000 (This port is external port for mapped port 10001). Click Create button to finish. Then check the DestIP, DestPort and Type, and click Connect button to link. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 104
Step 5) Test the link for sending and receiving At client PC, type “test from client to server”, and click Send button. At the server PC, it will receive the info the client PC. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 105
H685 User Manual At Server PC, type “reply from server to client”, and click Send button. At the client PC side, it will receive the related info from server PC side. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
H685 User Manual With this result, it indicates the port forwarding is working. 5.4 Remote Web Login Step 1) make H685 router to be online and get a public WAN IP. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 107
PC. So we cannot make the remote visit of the H685 router web. Let’s get a public IP for H685 router first. Here we change another sim card to test. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 108
H685 User Manual H685 router gets a WAN IP 183.43.55.249, which is a public IP, and can ping though. Step 2) Make sure the “Remote Management” feature is activated. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Please connect the RJ45 WAN port and the upper Router LAN RJ45 port via RJ45 cable. The H685 WAN LED should be on. Step 1) log into the H685 router web. Step 2) Internet Settings – Route Fail Over E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 110
Step 3) Internet Settings – WAN – WAN Connection Type – Cell. Configure the Cell WAN parameters. Please make sure H685 can be Cell online after this configuration. Otherwise the fail over feature will not work in redundancy E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 111
H685 User Manual Step 4) Internet Settings – WAN – WAN Connection Type – STATIC (fixed IP) Configure the STATIC (fixed IP), E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 112
Cell as secondary line. And if STATIC WAN RJ45 resume to work, it will switch from Cell line to STATIC WAN RJ45 line. The following page indicated the Static fixed IP is working. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
For example, here we set Cellular as secondary line, and WAN RJ45 DHCP as main line. Then choose as the picture above. Check Count: fill in the number you want to check the line available detection. Checking Method: fill in a public IP address that can be ping through. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 114
Please make sure H685 can be Cell online after this configuration. Otherwise the fail over feature will not work in redundancy Step 4) Internet Settings – WAN – WAN Connection Type – DHCP (Auto config) Choose “DHCP (Auto config)” at WAN Connection Type, and click “Apply” button E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Notes: if the DHCP cannot get WAN IP Address, please “Load Default” for H685 router to retry. 5.7 WAN RJ45 PPPoE and Cellular Fail Over backup redundancy Please connect the RJ45 WAN port and the ADSL modem RJ45 port via RJ45 cable. The H685 WAN LED E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 116
Step 3) Internet Settings – WAN – WAN Connection Type – Cell. Configure the Cell WAN parameters. Please make sure H685 can be Cell online after this configuration. Otherwise the fail over feature will not work in redundancy E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 117
H685 User Manual Step 4) Internet Settings – WAN – WAN Connection Type – PPPoE (ADSL) E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 118
Cell as secondary line. And if WAN RJ45 PPPoE resume to work, it will switch from Cell line to WAN RJ45 PPPoE line. The following page indicated the PPPoE is working. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Once the PPPoE (ADSL) is failed, H685 will switch to cellular automatically as follows, 5.8 SMS Reboot/Cell UP/Cell Down control Step 1) follow Chapter 3.3.9 to configure the SMS feature. We configure it as follows, E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 120
Send “celldown” from send’s phone number (here is 13798257916). In the System Log of the router, you can find the similar info "received index=0 msg (celldown) from (13798257916) !" The Router CELL will be offline, and WAN IP will be none as followed status. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 121
Log", there is info similar " received index=0 msg (cellstatus) from (13798257916) !". The router will feedback the CELL STATUS to sender’s phone number 13798257916. At 13798257916, we will get message of “Router E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Step 3) modify the “Default Gateway” same as “IP Address”, then click “Apply” button. 5.10 PPTP client connection PPTP Server’s Info: PPTP Server IP: 190.54.34.131 Username: vpnuser Password: tekrem9876 Remote LAN/Mask: 192.168.130.0/24 E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 123
Step 2) Fill in the PPTP parameters as follows, Step 3) check if the PPTP is connected. Router Web – Status, Step 4) Try to check if can be through with PPTP Server. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
1) Take two H685/H685 router, one for IPSec Server, the other is for IPSec client. For formal application, recommend use CISCO VPN Router for Server, and E-Lins Router for Client. 2) We configure Server Router gateway LAN IP as 192.168.8.1, and Client Router gateway LAN IP as 192.168.9.1.
Page 125
H685 User Manual IPSec Server Side Step 1) make the Server Router working online. Step 2) Fill in the IPSec parameters as follows, E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 126
H685 User Manual And “Advance” as follows, E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 127
Step 3) Active the configured IPsec profile. Select the profile, click “Enable” button, then it will show “Active” at “Active Status”. IPSec Client Side Step 1) make the Client Router working online. Step 2) Fill in the IPSec parameters as follows, E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 128
H685 User Manual And “Advance” as follows, Step 3) Active the configured IPsec profile. Select the profile, click “Enable” button, then it will show “Active” at “Active E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...
Page 129
For Client Side, it will display the following status, For Server Side, it will display the following satus, Test Result: Try to ping from Client to Server, and from Server to Client. If both is through, means working. E-Lins Technology Co.,Limited Tel: +86-755-29230581 E-mail: sales@e-lins.com sales@szelins.com www.szelins.com...