1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Security Camera
  5. Network Speed Dome Camera
  6. User manual

HIKVISION Network Speed Dome Camera User Manual

5-inch high-definition network speed dome
Hide thumbs Also See for Network Speed Dome Camera:
Table of Contents

Advertisement

Quick Links

See also: User Manual
5-inch High-definition Network
Speed Dome

User Manual

V4.0.2
Hangzhou Hikvision Digital Technology Co., Ltd.
http://www.hikvision.com

Advertisement

Table of Contents
loading

Related Manuals for HIKVISION Network Speed Dome Camera

Summary of Contents for HIKVISION Network Speed Dome Camera

  • Page 1: User Manual

    5-inch High-definition Network Speed Dome User Manual V4.0.2 Hangzhou Hikvision Digital Technology Co., Ltd. http://www.hikvision.com...
  • Page 2 Certification does not cover the performance or reliability of the security or signaling aspects of this product. UL MAKES NO REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.” © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 3: Regulatory Information

    The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 4: Safety Warnings And Cautions

    (AC power).The socket outlet shall be installed near the equipment and shall be readily accessible. Installation and Maintenance:Do not connect/disconnect any cables to or perform installation/maintenance on this device during an electrical storm. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 5 This equipment generates, uses and can radiate radio frequency energy which may result in harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 6 Lead Content: Please recycle this device in a responsible manner. Refer to local environmental regulations for proper recycling; do not dispose of device in unsorted municipal waste. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 7: Safety Instruction

     If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the product yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.) © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 8  Please use a soft and dry cloth when clean inside and outside surfaces of the product cover. Do not use alkaline detergents.  Improper use or replacement of the battery may result in hazard of explosion. Please use the manufacturer recommended battery type. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 9: Table Of Contents

    Configuring Park Actions ......................40 Configuring Privacy Mask ....................... 41 Clearing PTZ Configurations ....................42 Chapter 6 Speed Dome Configuration ..................43 Configuring Local Parameters ....................43 Configuring Time Settings ...................... 44 © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 10 Importing/Exporting Configuration File ................ 92 10.4.4 Upgrading the System ....................92 Chapter 11 Menu Tree ........................ 94 Appendix ............................95 Appendix 1 SADP Software Introduction .................... 95 Appendix 2 Port Mapping ........................97 © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 11: Chapter 1 Overview

     CGI(Common Gateway Interface), PSIA(Physical Security Interoperability Alliance), ONVIF(Open Network Video Interface Forum), to ensure greater interoperability between different platforms and compatibility  3D positioning function  Power-off memory function: restore PTZ & Lens status after reboot © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 12: Functions

    In manual tracking mode, when a target object goes directly beneath the dome, the video will automatically flips 180 degrees in horizontal direction to maintain continuity of tracking. This function can also be realized by auto mirror image © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 13  White Balance (WB) White balance can remove the unrealistic color casts. White balance is the white rendition function of the camera to adjust the color temperature according to the environment automatically.  Patrol © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 14 The dome allows you to edit users with different levels of permission, in the admin login status. Multiple users are allowed to access and control the same network speed dome via network simultaneously. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 15: Chapter 2 Network Connection

    Figure 2-1.  Refer to the Figure 2-2 to set the network speed dome over the LAN via a switch or a router. Figure 2-1 Connecting Directly © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 16: Detecting And Changing The Ip Address

     For accessing the network speed dome from different subnets, please set the gateway for the network speed dome after you logged in. For detailed information, please refer to Section 6.3.1 Configuring TCP/IP Settings. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 17: Setting The Network Speed Dome Over The Wan

    Note: Refer to Appendix 2 for detailed information about port mapping. 5. Visit the network speed dome through a web browser or the client software over the internet. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 18: Dynamic Ip Connection

    6. Configure the DDNS settings in the setting interface of the router. 7. Visit the speed dome via the applied domain name. Connecting the network speed dome via a modem  Purpose: © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 19 2. Configure the DDNS settings in the DDNS Settings interface of the network speed dome. Refer to Section 6.3.4 Configuring DDNS Settings for detailed configuration. 3. Visit the speed dome via the applied domain name.  Private Domain Name Resolution © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 20 2. Access the network speed dome through the LAN with a web browser or the client software. 3. Enable DDNS and select IP Server as the protocol type. Refer to Section 6.3.4 Configuring DDNS Settings for detailed configuration. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 21: Chapter 3 Access To The Network Speed Dome

    The default user name is admin, password is 12345. Figure 3-1 Login Interface 4. Install the plug-in before viewing the live video and operating the speed dome. Please follow the installation prompts to install the plug-in. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 22 User Manual of Network Speed Dome Figure 3-2 Download and Install Plug-in Figure 3-3 Install Plug-in (1) Figure 3-4 Install Plug-in (2) © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 23: Accessing By Client Software

    Follow the installation prompts to install the client software and WinPcap. The control panel and live view interface of iVMS-4200 are shown as bellow. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 24 3D Positioning: Steps: Click on the PTZ control panel of live view interface. Operate the 3D positioning function:  Left click a position of the live video. The corresponding position will be © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 25 Note: For detailed information about iVMS-4200 client software, please refer to the user manual of the iVMS-4200 software. This manual mainly introduces accessing to the network speed dome by web browser. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 26: Chapter 4 Live View

    Log in the network speed dome to enter the live view page, or you can click on the menu bar of the main page to enter the live view page. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 27: Starting Live View

    Configure the image size and stream type of the live video. 4.3 Starting Live View In the live view window as shown in Figure 4-3, click on the toolbar to start the live view of the speed dome. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 28  Setting the image quality of the live video in Section 6.1 Configuring Local Parameters and Section 6.4.1 Configuring Video Settings.  Setting the OSD text on live video in Section 6.5.2 Configuring OSD Settings. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 29: Recording And Capturing Pictures Manually

    Click the zoom/iris/focus buttons to realize lens control. Figure 4-4 PTZ Control Panel Table 4-2 Descriptions of PTZ Control Panel Button Description Zoom in/out Focus near/far Iris open/close Adjust speed of pan/tilt movements © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 30: Setting / Calling A Preset

    Note: You can configure up to 256 presets.  Calling a Preset: In the PTZ control panel, select a defined preset from the list and click to call the preset. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 31: Setting / Calling A Patrol

    A patrol is a memorized series of preset function. It can be configured and called on the patrol settings interface. There are up to 8 patrols for customizing. A patrol can be configured with 32 presets. Before you start: © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 32  Calling a Patrol: In the PTZ control panel, select a defined patrol from and click to call the patrol as shown in Figure 4-8. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 33: Setting / Calling A Pattern

    1. In the PTZ control panel, click to enter the pattern settings interface. 2. Select a pattern number from the list as shown in Figure 4-9. Figure 4-9 Patterns Settings Interface © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 34: Configuring Live View Parameters

    The main stream is with a relatively high resolution and needs much bandwidth. The sub-stream is with a low resolution and needs less bandwidth. The default setting of © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 35  Image Size: You can scale up/down the live view image by clicking . the image size can be 4:3, 16:9, original or auto. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 36: Chapter 5 Ptz Configuration

    3. Click Set to save the position. Call/delete an Initial Position:  You can click to call the initial position. You can click delete the initial position and restore the factory default initial position. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 37: Configuring Basic Ptz Parameters

     Auto Scan Speed: The dome provides 5 scan modes: auto scan, tilt scan, frame scan, random scan and panorama scan. The scan speed can be set from level 1 to 40. PTZ OSD: Set the on-screen display duration of the PTZ status.  © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 38: Configuring Ptz Limit Stops

    The dome can be programmed to move within the configurable limit stops (left/right, up/down). Steps: 1. Enter the Limit Configuration interface: Configuration > Advanced Configuration > PTZ > Limit Figure 5-3 Configure the PTZ Limit © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 39: Configuring Scheduled Tasks

    Figure 5-4 Configure Scheduled Tasks 2. Check the checkbox of Enable Scheduled Task. 3. Set the Park Time. You can set the park time (a period of inactivity) before the dome starts the scheduled tasks. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 40 Start Time and End Time for each task, and click Enter on your keyboard to enter the time. (4) Choose the task type from the drop-down list. You can choose scan, preset, pattern and etc. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 41: Configuring Park Actions

    2. Check the checkbox of Enable Park Action. 3. Set the Park Time as the inactivity time of the dome before it starts the park actions. 4. Choose Action Type the from the drop-down list. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 42: Configuring Privacy Mask

    ; click and drag the mouse in the live video window to draw the area. 4. Click to finish drawing or click to clear all of the areas you set without saving them. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 43: Clearing Ptz Configurations

    1. Enter the Clearing Configuration interface: Configuration > Advanced Configuration> PTZ > Clear Config 2. Check the checkbox of the items you want to clear. 3. Click to clear the settings. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 44: Chapter 6 Speed Dome Configuration

    HTTP: Allows the same quality as of TCP without setting specific ports for streaming under some network environments. MULTICAST: It’s recommended to select the protocol type to when using the Multicast function. For other information about Multicast, © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 45: Configuring Time Settings

    Network Time Protocol(NTP) server and manual mode. To enter the Time Settings interface: Configuration > Basic Configuration > System > Time Settings Or Configuration > Advanced Configuration > System > Time Settings © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 46 If the speed dome is connected to a public network, you should use a NTP server that has a time synchronization function, such as the server at the National Time Center (IP Address: 210.72.145.44). If the speed dome is set in a customized © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 47 If there is the habit of adjusting clocks forward in your country in certain time period of a year, you can turn this function on. The time will be adjusted automatically when the Daylight Saving Time(DST) comes. Steps: (1) Check to enable the DST function. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 48: Configuring Network Settings

    TCP/IP settings must be properly configured before you operate the speed dome over network. Steps: 1. Enter TCP/IP Settings interface: Configuration > Basic Configuration > Network > TCP/IP Or Configuration > Advanced Configuration > Network > TCP/IP © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 49: Configuring Port Settings

    Network (WAN), you need to set the 3 ports for the speed dome. Steps: 1. Enter the Port Settings interface: Configuration > Basic Configuration > Network > Port Or Configuration > Advanced Configuration > Network > Port Figure 6-9 Port Settings © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 50: Configuring Pppoe Settings

    Registration on the DDNS server is required before configuring the DDNS settings of the speed dome. Steps: 1. Enter the DDNS Settings interface: Configuration > Advanced Configuration > Network > DDNS © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 51 IP Server: Steps: (1) Enter the Server Address of the IP Server. (2) Click to save the settings. Note: The Server Address should be entered with the static IP address of the © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 52: Configuring Snmp Settings

    Note: The SNMP version you select should be the same as that of the SNMP software. Steps: 1. Enter the SNMP Settings interface: Configuration > Advanced Configuration > Network > SNMP © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 53 ) to enable the feature. 3. Configure the SNMP settings. Note: The configuration of the SNMP software should be the same as the settings you configure here. 4. Click to save and finish the settings. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 54: Configuring Ftp Settings

     Child directory: It is a sub-folder which can be created in the parent directory. The files will be saved in a sub-folder in FTP server. The name of folder can be defined as shown in following Figure 6-17. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 55: Configuring Video And Audio Settings

    2. Select the Stream Type of the speed dome to main stream (normal) or sub-stream. The main stream is usually for recording and live viewing with good bandwidth, and the sub-stream can be used for live viewing when the bandwidth is limited. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 56: Configuring Audio Settings

    1. Enter the Audio Settings interface Configuration > Basic Configuration > Video / Audio > Audio Or Configuration > Advanced Configuration > Video / Audio > Audio Figure 6-19 Audio Settings 2. Configure the following settings. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 57: Configuring Image Settings

    1. Enter the Display Settings interface: Configuration > Basic Configuration> Image> Display Settings Or Configuration > Advanced Configuration> Image> Display Settings 2. Set the image parameters of the speed dome. Figure 6-20 Display Settings © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 58: Exposure Mode

    The minimum focus value varies depending on the models of speed dome. Exposure Mode The Exposure Mode can be set to Auto, Iris Priority, Shutter Priority, Manual.  Auto: The iris, shutter and gain values will be adjusted automatically according to the © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 59 In Day mode, the speed dome displays color image. It is used for normal lighting conditions.  Night: In Night mode, the image is black and white. Night mode can increase the sensitivity in low light conditions. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 60: Slow Shutter

    In Manual mode, you can adjust the color temperature manually to meet your own demand as shown in Figure 6-26. Figure 6-26 Manual White Balance  Auto Tracing: In Auto Tracing mode, white balance is continuously being adjusted in real-time © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 61: Configuring Osd Settings

    Camera Name: Identifies the name of speed dome. You can customize the on screen display of time. Steps: 1. Enter the OSD Settings interface: Configuration > Advanced Configuration > Image > OSD Settings © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 62: Configuring Text Overlay Settings

    3. Input the characters in the textbox. 4. Use the mouse to click and drag the red text frame in the live view window to adjust the text overlay position. 5. Click © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 63: Configuring And Handling Alarms

    Steps: 1. Set the Motion Detection Area. Steps: (1) Enter the motion detection settings interface Configuration > Advanced Configuration> Events > Motion Detection (2) Check the checkbox of Enable Motion Detection. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 64 (5) Move the slider to set the sensitivity of the detection. 2. Set the Arming Schedule for Motion Detection. Steps: (1) To edit the arming schedule as shown in Figure 6-32, click Figure 6-31. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 65 (Optional). (5) Click to save the settings. Note: The time of each period can’t be overlapped. Up to 4 periods can be configured for each day. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 66  Send Email Send an email with alarm information to a user or users when an event occurs. Note: To send the Email when an event occurs, you need to refer to Section © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 67: Configuring Tamper-Proof Alarm

    You can configure the speed dome to trigger the alarm actions when the lens is covered. Steps: 1. Enter the Tamper-proof Settings interface: Configuration > Advanced Configuration > Events > Tamper-proof © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 68: Configuring External Alarm Input

    Step 3 Set the Alarm Actions for Motion Detection in Section 6.6.1 Configuring Motion Detection. 6. Click to save the settings. 6.6.3 Configuring External Alarm Input Steps: 1. Enter the Alarm Input Settings interface: © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 69 6. You can also choose the PTZ linking for the alarm input. Check the relative checkbox and select the No. to enable Preset Calling, Patrol Calling or Pattern Calling. 7. You can copy your settings to other alarm inputs. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 70: Configuring Alarm Output

    Refer to Step 2 Set the Arming Schedule for Motion Detection in Section 6.6.1 Configuring Motion Detection. 6. You can copy the settings to other alarm outputs. 7. Click to save the settings. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 71: Handling Exception

    Steps: 1. Enter the Exception Settings interface: Configuration > Advanced Configuration> Events > Exception 2. Check the checkbox to set the actions taken for the Exception alarm. Refer to © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 72: Configuring Email Settings

    Please configure the DNS Server settings under Basic Configuration > Network > TCP/IP or Advanced Configuration > Network > TCP/IP before using the Email function. Steps: 1. Enter the Email Settings interface: Configuration > Advanced Configuration > Events > Email © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 73 Receiver: Select the receiver to which the email is sent. Up to 2 receivers can be configured. Receiver: The name of the user to be notified. Receiver’s Address: The email address of user to be notified. 3. Click to save the settings. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 74: Configuring Snapshot Settings

    Please refer to Step 3 Set the Alarm Actions Taken for Motion Detection in Section 6.6.1 Configuring Motion Detection, or Step 4 Configuring External Alarm Input in Section 6.6.1 Configuring Motion Detection. 3) Check the Enable Event-triggered Snapshot checkbox. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 75 User Manual of Network Speed Dome Figure 6-40 Snapshot Settings © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 76: Chapter 7 Record Settings

    (2) If the status of the disk is Uninitialized as shown in Figure 7-2, check the corresponding checkbox to select the disk and click to start initializing the disk. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 77: Configuring Recording Schedule

    By default, the record files of scheduled recording are stored in the SD card (if supported) or in the network disk. Steps: 1. Enter the Record Schedule Settings interface: Configuration > Advanced Configuration> Storage > Record Schedule © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 78 25 s, 30 s or not limited. Note: The pre-record time changes according to the video bitrate.  Post-record: The time you set to stop recording after the scheduled time or © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 79 If you select Normal, the video will be recorded automatically according to the time of the schedule.  Record Triggered by Motion Detection If you select Motion Detection, the video will be recorded when the © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 80 Besides configuring the recording schedule, you have to configure the settings on the Motion Detection and Alarm Input Settings interfaces. Please refer to Section 6.6.1 and Section 6.6.4 for detailed information. Figure 7-8 Edit Record Schedule © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 81 You can also check any of the checkboxes before the date and click (4) Click to save the settings and exit the Edit Record Schedule interface. 6. Click to save the settings. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 82: Chapter 8 Playback

    Task 1: To play back the video files Steps: 1. Click on the menu bar to enter playback interface. Figure 8-1 Playback Interface 2. Select the date and click Figure 8-2 Search Video © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 83 You can also click to zoom out/in the progress bar. Figure 8-4 Set Playback Time Figure 8-5 Progress Bar The different colors of the video on the progress bar stand for the different video © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 84  You can click to stop the downloading.  The total number displays the amount of the video files.  The video files are not all listed on one page. You can click © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 85 User Manual of Network Speed Dome to turn pages. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 86: Chapter 9 Log Searching

    Minor Type, Start Time and End Time as shown in Figure 9-2. 3. Click to search log files. The matched log files will be displayed on the Log interface. Figure 9-2 Log Searching © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 87 User Manual of Network Speed Dome 4. To export the log files, click to save the log files in your computer. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 88: Chapter 10 Others

    Operator or User. 3. In the Basic Permission field and Camera Configuration field, you can check or uncheck the permissions for the new user. 4. Click to finish the user addition. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 89 2. Modify the User Name, Level or Password. 3. In the Basic Permission field and Camera Configuration field, you can check or uncheck the permissions. 4. Click to finish the user modification. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 90  Delete a User Steps: 1. Left-click the user name you want to delete and click 2. Click on the pop-up dialogue box to delete the user. Figure 10-4 Delete a User © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 91: Configuring Rtsp Authentication

    Version, Encoding Version, Number of Channels, Number of HDDs, Number of Alarm Input and Number of Alarm Output are displayed. The information cannot be changed in this menu. It is the reference for maintenance or modification in future. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 92: Maintenance

    Figure 10-7 Reboot the Device 10.4.2 Restoring Default Settings Steps: 1. Enter the Maintenance interface: Configuration > Basic Configuration> System > Maintenance Or Configuration > Advanced Configuration> System > Maintenance © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 93: Importing/Exporting Configuration File

    Figure 10-9 Import/Export Configuration File 10.4.4 Upgrading the System Steps: 1. Enter the Maintenance interface: Configuration > Basic Configuration> System > Maintenance Or Configuration > Advanced Configuration> System > Maintenance © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 94 The upgrading process will take 1 to 10 minutes. Please don't disconnect power of the speed dome during the process. The speed dome reboots automatically after upgrading. Figure 10-10 Remote Upgrade © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 95: Chapter 11 Menu Tree

    You may need to use the OSD(On Screen Display) menu when controlling the speed dome remotely. To display the OSD menu on the live view screen, you can call the preset number 95. The OSD menu tree is shown as follows: © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 96: Appendix

    You can also click to refresh the online device list manually. The newly searched devices will be added to the list. Note: You can click on each column heading to order the © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 97 Serial code is a series of characters combined by the start time and the serial number of the device. 2. Input the code in the Serial code field and click to restore the default password. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.

  • Page 98: Appendix 2 Port Mapping

     In the speed dome, the 8200~8210 ports change with the 8000 port with a constant value of 200. E.g. if the 8000 port is changed to 8005, then the 8200~8210 ports should be changed to 8205~8215. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 99 The port of the network speed dome cannot conflict with other ports. For example, some web management port of the router is 80. Change the speed dome port if it is the same as the management port. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
  • Page 100 First Choice for Security Professionals...

This manual is also suitable for:

5-inch high-definition network speed dome

Table of Contents