Related Manuals for GE Choice Alert
Summary of Contents for GE Choice Alert
- Page 1 Wireless Alarm System Motion Sensor User’s Manual Choice Choice ALERT ALERT ™ ™ Control all Sensors & accessories from one location...
-
Page 2: Table Of Contents
Table of Contents Important Safeguards Introduction Assigning a Sensor to a Zone Testing a Sensor or your system Installation Erasing a Sensor from a Zone Low battery indicator Battery warnings 12-13 Optional Accessory 14-15 F.A.Q.'S 16-17 FCC Warning... - Page 3 Alarm systems. The Choice Alert system is reliable and easy-to-use. With Choice Alert you can select from a line of Sensors and Accessories; start small and expand as you need, or create a system that meets all your needs.
-
Page 4: Important Safeguards
Motion Sensor’s warranty. 3. If you feel the Motion Sensor or any part of the Choice Alert system is not operating correctly or as described, please contact Technical Support for assistance (1-800-654-8483). -
Page 5: Introduction
Introduction The Motion Sensor is designed to be used indoors or out. When mounted properly it can monitor large or open areas such as entrances, living rooms, family rooms, driveways, backyards, walkways, workshops, etc. When the Sensor detects motion, it will transmit a signal to the Control Center. -
Page 6: Assigning A Sensor To A Zone
12∞ Preparing the Motion Sensor for Installation The Motion Sensor consists of 2 parts – The Sensor (Transmitter) and the wall mount. Before installing, SENSOR remove the screw from the battery door on the back of the Sensor. You’ll need to attach the battery leads to a “9V”... -
Page 7: Testing A Sensor Or Your System
- To activate the Motion Sensor, press the Learn button located inside the battery compartment, or if mounted wave your hand in front of the Sensor (the red LED indicator will flash inside lens area in front of the Motion Sensor). Step 1 Press and hold the Learn button... -
Page 8: Installation
Step 3 - Set the Notification Mode to switch ‘Alert’ position and begin activating Sensors one at a time. Note: The sensor has a LED that flashes to show when the sensor has triggered and transmitted to the main unit. Step 4 - When testing is complete, unplug the AC adapter, then plug the AC adapter back in and reinstall batteries. -
Page 9: Erasing A Sensor From A Zone
Erasing the Sensor from a Zone Note: If you need to remove the Sensor from a Zone, the system will erase the entire Zone, so any other Sensors will need to be put back into that particular Zone. Step 1 - To erase a Zone, press and hold the Learn button on the Control Center. - Page 10 However, you can check the Motion Sensor status independently by placing the Control Center in Test mode (see Testing a Sensor on page 7) and trigger the Sensor separately. If mounted, wave hand in front of Sensor, or press activation button for two seconds inside battery compartment.
-
Page 11: Battery Warnings
Description Battery Type Battery Life* Control Center (4) “AAA” 24 months MotionSensor (1) “9V” 9 months *maximum potential life based upon usage and location WARNING! Risk of personal injury - Prolonged exposure to alarm siren may cause permanent hearing loss Battery Warnings! - Remove batteries before storing the Alarm or Sensor for extended periods... -
Page 12: Optional Accessory
Siren Signal Silent alert Repeater The Signal Repeater will extend the range of the Choice Alert system up to 150 feet from its Test location – Effectively repeating the signal from any Sensor back to the Control Center should a Sensor be located out of range. - Page 13 Step 3 - When the Signal Repeater receives the confirmation signal, the LED indicator will flash, five times. If the Signal Repeater does not receive the confirmation signal from the Control Center, the LED indicator on the Signal Repeater will not flash.
-
Page 14: F.a.q.'s
Motion Sensor F.A.Q.’S Q. I bought a new Sensor and the Control Center will not recognize it. Why? A. First, make sure that the battery is new and has been correctly attached to the terminals. Confirm that the Sensor has been correctly assigned to a Zone. Q. - Page 15 Sensor. This will cause low battery indication on the Control Center (See pg 10). Q. Why does one of my Zones continually flash? A. This can be caused by 1 of 2 conditions. First condition, if it is a rapid flash it means a Sensor in the Zone has a low battery.
-
Page 16: Fcc Warning
Any unauthorized changes or modifications to the equipment would void the user’s warranty and may conflict with both state and federal laws. The Choice Alert system complies with part 15 of the FCC rules. Operation is subject to the following... - Page 17 Compliance with IC Rules and Regulations IC6924A-45132 Jasco Products 45132 Object is subject to the following two conditions. This device may not cause interference, and This device must accept any interference, including interference that may cause undesired operation of the device. WARNING Limitations of Alarm Products This product should be tested periodically to make sure...
- Page 18 is a trademark of the General Electric Company and is used under license by Jasco Products Company LLC, 10 E. Memorial Road, Oklahoma City, OK 73114. This Jasco product comes with a 1 year limited warranty. Visit 45314-1 www.jascoproducts.com for details. 45132-4 Manual Version 5 03/08/12...