Advertisement
Quick Links
Download this manual
See also:
Operating Manual
Design and specifications are
subject to change without notice.
P/N:3810-0104C
Rev 0 06/03
Need Help?
Call 1.800.796.CCTV for sales, service and customer support.
www.honeywellvideo.com
READ AND KEEP THIS
OPERATION MANUAL
. User Information
3-Axis
C AU T I O N
INFORMATION
This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15
RISK OF ELECTRIC SHOCK
of the FCC Rules.
DO NOT OPEN
These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment.
CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
Explanation of two Symbols
required to correct the interference at their own expense.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of un-insulated
WARNING
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The manufacturer could void the user's authority to operate the equipment.
The exclamation point within an equilateral triangle is intended to
CAUTION - To prevent electric shock and risk of fire hazards:
alert the user to the presence of important operating and maintenance-
Do NOT use power sources except for that specified.
(servicing) instructions in the literature accompanying the appliance.
Do NOT expose this appliance to rain or moisture.
THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM OF THE SYSTEM.
This installation should be made by a qualified service person and should abide to all local codes.
"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE"
2
. Contents
3-Axis
3-Axis
Thank you for purchasing this COLOR VIDEO CAMERA.
Read Instructions
Before using this camera, please read this operation manual carefully to obtain
Read all of the safety and operating instructions
the best result and keep this manual for future reference.
before using the product.
Retain Instructions
Save this instructions for later use.
...........
........................
1. SAFETY INSTRUCTIONS
5
6. CONNECTIONS
10
Cleaning
..........................
...........
2. PRECAUTIONS
6
7. NAME AND FUNCTIONS
11
Unplug this appliance from wall outlet before
cleaning. Do not use liquid cleaners or aerosol
................................
...............
3. FEATURES
7
8. OPERATING CAMERA
12
cleaners. Use a damp cloth for cleaning.
..........................
......................
4. COMPOSITION
8
9. SPECIFICATIONS
34
Water and Moisture.
Do not use this product near water or moisture.
..........................
...............
5. INSTALLATION
9
10. TROUBLESHOOTING
36
(For example. near a bathtub, wash bowl, kitchen
sink, or laundry tub, in a wet basement, or near a
swimming pool,etc)
4
2. PRECAUTIONS
3-Axis
3-Axis
Handling
Do not disassemble the camera and never touch
Be sure the ambient temperature is less than
parts inside the camera.
40¡É in installation intended for long ter m
continuous operation.
Do not drop the camera or subject it to shocks
and vibrations to avoid possible damage.
Avoid installing in a humid or dusty place.
When attaching or removing the lens, handle
Avoid installing in places where there are
with care in order to that moisture and dust do
strong magnetic fields and electric signals.
not enter the camera.
Avoid installing in places where the camera
would be subject to strong vibrations.
Installation and storage
Never expose the camera to rain and water.
Do not point the camera at the sun. This could
damage the camera whether it is operating or not.
Do not install the camera where the temperature
could exceed the allowable range.
6
4. COMPOSITION
3-Axis
3-Axis
1
Stick the guide pattern on the wall or ceiling.
2
Drill four holes according to the guide pattern
then insert anchors into the drilled holes.
L-Wrench
Guide Pattern
3
Draw out power / video wires to the
connecting places.
Operation Manual
4
Fixed the camera to a celling using four screws.
5
Adjust desired focus and scene by turning and
Mounting Screw
moving the 3-axis camera bracket by hand.
6
Put the dome cover over the base.
Service Monitor Cable
7
Fix the dome cover on the base by L-Wrench.
8
6. CONNECTION
3-Axis
3-Axis
Video
Video Output
#1
(Yellow)
GND
Power- 12VDC
#2
(Red)
• The wire is polarized.
• Use 12V DC
power source.
No.
Function
Terminal Color
R e m a r k
#1
Video Output
Yellow
1.0 Vp-p
#2
Power Input
Red
12VDC (10V~15V), 360mA (Max)
10
8. OPERATING CAMERA
3-Axis
!
Push the Joy stick for one second, and the OSD
appears on the screen. Move the Joy Stick up, down,
S E T U P M E N U
left & right to control the OSD functions.
CAMERA ID
• ON
• OFF
LENS
• MANUAL
• VIDEO
• DC
UP
SHUTTER
• AUTO
• FLK
• FIXED
• MANUAL
WHITE BAL.
• ATW
• AWB
• FIXED
• MANUAL
LEFT
FUNCTION
• BLC
• AGC
• PRIVACY
• MIRROR
• GAMMA
• MOTION
DOWN
ADJUST
• CONTRAST
• SHARPNESS
• CB _ GAIN
• CR _ GAIN
LANGUAGE
• ENGLISH • KOREAN
• CHINESE1 • CHINESE2 • JAPANESE
J613
UP
RESET
J611
LEFT
EXIT
DOWN
12
SETUP
Main Menu -
1) CAMERA ID setup (default setting OFF)
¨ç P ress MENU key in ON ¢× state.
1. Press MENU button, then SETUP mode is activated.
(Access ID setting MODE)
• MAIN SETUP menu is displayed on the monitor.
¨è P ress MENU key in CAMERA ID.
SE T U P
CAMERA ID
OFF
¨é Character is changed each time UP, DOWN is
2. Select OSD item using UP, DOWN button.
LENS
DC ¢×
pressed. (Can select up to 63 letters)
SHUTTER
FIXED ¢×
WHITE BAL.
ATW
¨ê P ress MENU button in ¢× to
3. Set details using LEFT, RIGHT button.
FUNCTION
¢×
exit from ID setup mode
ADJUST
¢×
LANGUAGE
ENGLISH
¨ë P ress MENU button in 'C' to correct and erase
RESET
¢×
the chosen entry.
4. Select "Exit" and then press the MENU button
EXIT
to finish the SETUP (Save and Exit)
2) POSITION setup. Press POSITION ¢×.
¨ç Move the character using UP, DOWN, LEFT, RIGHT button.
¨è P ress Menu button to confirm selection of the character.
¨é P ress Return to go to previous screen. ID is displayed by pressing EXIT on MAIN MENU.
14
LENS
Main Menu -
1) LENS setup
HD73
¨ç P ress LEFT or RIGHT button in LENS on
Series
Main Menu to select the mode to
MANUAL ¢¸ ¢º VIDEO ¢¸ ¢º DC ¢× .
Operation Manual
!
Setting Mode : DC ¢×
Vandal-Resistant
2) DC LENS setup
Dome Camera
¨ç P ress MENU button in DC ¢× to display the
screen on the right side.
¨è Use LEF T, RIGHT button to change
BRIGHTNESS(IRIS LEVEL) value.
¨é P ress MENU button to return to the previous screen.
www.honeywellvideo.com
16
Menu [SHUTTER] -
FIXED Mode Setup
1) FIXED
¢×
setup (MANUAL,DC,VIDEO LENS)
¨ç P ress MENU button in FIXED ¢×
to display the screen on the right side.
¨è P ress LEFT or RIGHT button in SHUTTER.
Can be set in ([NTSC: 1/60 ~ 1/100,000]
[PAL: 1/50 ~ 1/100,000]) range.
3
18
1. SAFETY INSTRUCTIONS
Main Menu -
FUNCTION
1) FUNCTION
¢×
setup
Installation
¨ç P ress MENU button in FUNTION
Do not place this product on an unstable cart, stand,
to show the OSD display on the right.
or table. The product may fall causing serious injury
to a child or adult, and damage to the product.
Use only with a cart or stand recommended by the
2) Select item using UP, DOWN button.
manufacturer, or sold with the product.
Mounting should follow the manufacturer's instructions,
3) Set details using LEFT, RIGHT button.
and should use a mounting accessory recommended
by manufacturer.
4) Click "Return" to go to MAIN SETUP
Power source
This product should be operated only from the type
of power source indicated on the marking label.
If you are not sure of the type of power supplied to
your home, consult your dealer or local power
company.
5
20
3. FEATURES
Menu [FUNCTION] -
1) BLC AREA MODE
High Sensitivity 1/3 Inch Sony Super HAD CCD
¨ç Exit from BLC AREA MODE
to move to BLC SETUP MODE screen.
Min. Illumination (F1.2, 30 IRE) : 0.3 Lux (Color)
0.0 Lux (IR LED On)
2) BLC OSD description
Day & Night (ICR)
¨ç ALL CLEAR - Clear all set AREA
OSD (On Screen Display)
¨è ALL SET - Set all 64 BLC AREA
High Performance Menus For Functions
¨é RETURN - R eturn to BLC AREA setup mode.
• Privacy Zone Selectable (4 Programmable Zone)
• Motion Detection Selectable (64 Programmable Zone)
¨ê EXIT - Save AREA and retur n to
BLC SETUP MODE.
• Sharpness Enhanced Adjustable
• Flickerless Selectable
• Gamma Enhanced Selectable
• BLC Zone Selectable (64 Programmable Zone)
7
22
5. INSTALLATION
Menu [FUNCTION] -
1) AGC setup
Ceiling
¨ç AGC default setting ON ¢×
Guide Pattern
¨è P ress MENU button in ON ¢×
to display the screen on the right side.
Dome Base
¨é Use LEF T, RIGHT button
to adjust AGC GAIN value (0~255)
0:MIN , 255:MAX
Mounting
¨ê P ress MENU button to return
Screw
to the previous screen.
Dome Cover
L-Wrench
9
24
7. NAME AND FUNCTIONS
Menu [FUNCTION] -
4
1) MIRROR setup
¨ç MIRROR default setting OFF
5
ON setting - Use LEFT, RIGHT button.
6
7
¨è Lef t and Right side is switched
as shown on the picture.
1
3
2
Camera Lay-out
OFF
1
Tilt rotation: Adjusting the vertical angle.
Pan rotation: Adjusting the horizontal angle.
2
3
Horizontal rotation: Adjusting the horizontal position of the screen.
4
Focus handle: Focus (Far or Near)
5
Zoom handle: Zoom (Tele or Wide)
6
IR LED
(3.8mm~9.5mm)
: 850nm/ 30¡Æ(20EA), P ower Consumption(4.5W)
7
Sensor
11
26
Setting up the Menu
Menu [FUNCTION] -
1) MOTION DETECTION setup
SETUP
¨ç DEF AULT value OFF
- Push and hold MENU button 1 second
¨è In ON ¢× , press MENU button.
to access the setup mode.
¨é Display MOTION details.
• Select the status using the
SW1
MENU(SET):
joystick. (up, down, left, right)
2) AREA
¢×
setup
SET BY JOY STICK
RIGHT
¨ç In AREA ¢× , press MENU button. (see p.29)
S E TU P
CAMERA ID
OFF
3) MOTION TH. Setup
LENS
DC ¢×
J601
¨ç Set motion sensitivity 0(MAX)~255(MIN)
SHUTTER
FIXED ¢×
WHITE BAL.
ATW
FUNCTION
¢×
4) MOTION TRACE setup
ADJUST
¢×
Service Monitor Connecter:
¨ç ON : Display motion detection AREA .
LANGUAGE
ENGLISH
Use service monitor
RESET
¢×
SW1
connector to set camera angle
!
EXIT
Setting value can be adjusted
RIGHT
& focus when installing.
using LEFT or RIGHT button.
13
28
CAMERA ID
Main Menu -
Menu [FUNCTION] -
1) MOTION OSD description
¨ç ALL CLEAR - R elease all set AREA
¨è ALL SET - Set all 64 MOTION AREA .
I D SETUP
¨é RETURN - R eturn to MOTION AREA Setup Mode.
CAMERA ID
¨ê EXIT - Save AREA and retur n to MOTION SETUP MODE.
A
¢×
C
_
POSITION
RETURN
15
30
1) SHUTTER setup (for LENS MANUAL)
¨ç P ress LEFT or RIGHT button in SHUTTER
to select the mode to
AUTO ¢× ¢¸ ¢º FLK ¢¸ ¢º FIXED ¢×
¢¸ ¢ºMANU AL ¢× .
LEN S D C
!
Setting Mode : FIXED ¢×
BRIGHTNESS
056
¢× : RETURN
Menu [WHITE BAL.] -
1) WHITE BALANCE setup
SHUT TER FIXED
¨ç In WHITE BAL., press LEF T, RIGHT button
to select the mode you wish to operate
ATW ¢¸ ¢º A WB ¢¸ ¢º FIXED ¢×
¢¸ ¢ºMANU AL ¢× .
SHUTTER M : 1/60
2) FIXED
¢×
setup
¢× : RETURN
¨ç Can set from MODE 1 to MODE 4.
3) MANUAL
¢×
setup
¨ç As shown on the lower right picture,
set Red and Blue color value temperature.
¨è P ress MENU button in RETURN
to exit from setup mode.
1) BLC SETUP MODE
¨ç P ress MENU button in BLC ON ¢× ,
to display the screen on the right side.
F UN CTI O N
BLC
OFF
2) BLC AREA
¢×
setup
AGC
ON ¢×
PRIVACY
OFF
¨ç Use UP, DOWN, LEFT, RIGHT button
MIRROR
OFF
to move the AREA setup position.
GAMMA
0.45
MOTION
OFF
RETURN
¨è Set or release BLC AREA
using MENU button.
¨é P ress MENU button for more than 1 second
to move to BLC AREA MODE.
BLC 2
1) BLC RATIO setup (BLC LEVEL value setup)
¨ç Use UP,DOWN button
to move to BLC RATIO.
¨è Use LEF T, RIGHT button
BLC AREA
to change BLC LEVEL value (0~63)
ALL CLEAR
0:MIN , 63:MAX
ALL SET
RETURN
¨é P ress MENU button in RETURN
EXET
to move to FUNCTION MODE.
AGC
1) PRIVACY setup
¨ç Default setting OFF - Use LEF T,RIGHT button.
Change setup to ON ¢× mode.
¨è Af ter ON ¢× mode setup, 4 AREA groups are
AG C CONT R O L
configured as displayed on the right-side picture.
¨é P ress MENU button.
Details of each area is dsplayed.
095
AGC GAIN
2) PRIVACY details setup
¢× : RETURN
¨ç Select AREA SEL - PRIV ACY 0~3.
¨è AREA ST ATE - 0~3 AREA ON/OFF
¨é LEF T - Change left portion of each AREA size.
¨ê RIGHT - Change right por tion of each AREA size.
¨ë TOP - Change top por tion of each AREA size.
¨ì BOTTOM - Change bottom portion of each AREA size.
¨í COLOR - Change entire color of the AREA (16 COLOR)
MIRROR
1) GAMMA setup (DEFAULT 0.45)
F UN CTI ON
¨ç In FUNCTION MODE,
BLC
OFF
use UP , DOWN button to select GAMMA.
AGC
ON ¢×
PRIVACY
OFF
¨è Use LEF T, RIGHT button
MIRROR
OFF
GAMMA
0.45
to adjust GAMMA value.
MOTION
OFF
(USER ¢¸ ¢º 0.05 ¢¸ ¢º 0.10 ¢¸ ¢º 0.15 ~ 1.0)
RETURN
ON
MOTION
1) MOTION AREA setup
F UN CTI ON
¨ç Use UP, DOWN, LEFT, RIGHT button
BLC
OFF
to move AREA setting position.
AGC
ON ¢×
PRIVACY
OFF
¨è Use MENU button to set and release AREA .
MIRROR
OFF
GAMMA
0.45
MOTION
OFF
¨é P ress MENU button for more than 1 second
RETURN
to move to MOTION AREA MODE
2) MOTION AREA MODE
MOT ION
¨ç Y ou will return to MOTION AREA MODE
after "Exit" from MOTION AREA MODE.
AREA ¢×
MOTION TH.
037
OFF
MOTION TRACE
RETURN
MOTION AREA 2
1) ADJUST setup
¨ç P ress MENU button in ADJUST.
¨è Move to screen on the right side.
!
Each LEVEL value can be
adjusted using LEFT, RIGHT button.
2) CONTRAST setup
¨ç Adjust Y -gain value (0~255)
3) SHARPNESS setup
¨ç Adjust aper ture value (0~31)
4) CB _ GAIN setup
¨ç Adjust COL OR CB _ GAIN value (0~255)
5) CR _ GAIN setup
¨ç Adjust COL OR CR _ GAIN value (0~255)
SHUTTER AUTO
LANGUAGE
Menu [SHUTTER] -
Main Menu -
1) LANGUAGE setup
¨ç DEF AULT value - ENGLISH
¨è Af ter selecting LANGUAGE,
SE TUP
SHUT TER AUTO
CAMERA ID
change setting using LEFT or RIGHT button.
LENS
SHUTTER
¨é Choose the language mode you
WHITE BAL.
BRIGHTNESS
056
wish to operate in.
FUNCTION
ADJUST
LANGUAGE
RESET
¢× : RETURN
EXIT
!
ENGLISH ¢¸ ¢º K orean ¢¸ ¢º Chinese1 ¢¸ ¢º Chinese 2 ¢¸ ¢º Japanese
17
32
9. SPECIFICATIONS
WHITE BALANCE Mode Setup
3-Axis
MODEL
H D 7 3
AWB FIXE D
Signal System
NTSC
Image Sensor
2:1 Interlace Transfer 1/3 Inch Super HAD CCD
Effective Pixels
768(H) x 494(V)
AWB FIXED : MODE 1
Video Output
Composite: 1.0Vp-p, 75¥Ø, Unbalanced
Sync. System
Internal Sync
¢× : RETURN
Luminance S/N Ratio
More than 50dB (AGC OFF)
Horizontal Resolution
530 TV Lines
Min. Illumination (F1.2)
0.3 Lux(30IRE, AGC ON), 0 Lux(IR LED)
AWB MANUAL
Lens
DC Auto IRIS Vari-focal (f=3.8~9.5mm)
RED
113
Focus
Manual
BLUE
255
Electronic Shutter
1/60~1/100,000
White Balance
ATW (1,800¢ª K~10,500¢ª K) / AWB / Fixed / Manual
¢× : RETURN
Camera ID
ON / OFF
Language
English / Korean / Chinese 1 / Chinese 2 / Japanese
19
34
10. TROUBLESHOOTING
3-Axis
Menu [FUNCTION] -
BLC 1
If you have trouble operating your camera, refer to the following table.
If the guidelines do not enable you to solve the problem, contact an authorized technician.
BLC SETUP
P r o b l e m
S o l u t i o n s
BLC AREA ¢×
Nothing appears on the
• Check that the power cord and line connection between the camera and monitor
BLC RATIO
16
screen.
are fixed properly.
• Check that you have properly connected VIDEO cable to the camera VIDEO output jack.
RETURN
The image on the screen
• Is lens stained with dirt? Clean your lens with soft, clean cloth.
is dim.
• Set the monitor to proper condition.
• If the camera is exposed to too strong light, change the camera position.
• Adjust the lens' focus properly.
The image on the screen
• Adjust the contrast feature of the monitor.
is dark.
• If you have an intermediate device, set the 75§Ù/ Hi-z properly .
• Adjust DC Level, on the OSD menu.
• Check that you have properly connected the camera to an appropriate power source.
The camera is not working
properly, and the surface
of the camera is hot.
The image on the screen
• Is the camera facing to direct sunlight or fluoresent lighting?
flickers.
Change the camera position.
21
36
BLC 3
Menu [FUNCTION] -
BLC SETUP
BLC AREA ¢×
BLC RATIO
16
RETURN
23
38
Menu [FUNCTION] -
PRIVACY
FUNCTION
BLC
ON ¢×
AGC
ON ¢×
PRIVACY
ON ¢×
MIRROR
OFF
GAMMA
0.45
MOTION
OFF
RETURN
PRIVACY
AREA SEL
AREA 0
AREA STATE
ON
LEFT
017
RIGHT
058
TOP
020
BOTTOM
055
COLOR
001
RETURN
25
Menu [FUNCTION] -
GAMMA
FUNCTION
BLC
OFF
AGC
ON ¢×
PRIVACY
OFF
MIRROR
OFF
GAMMA
0.45
MOTION
OFF
RETURN
27
MOTION AREA 1
Menu [FUNCTION] -
MOTION AREA
ALL CLEAR
ALL SET
RETURN
EXET
29
ADJUST
Main Menu -
ADJUST
CONTRAST
083
SHARPNESS
12
CB _ GAIN
190
CB _ GAIN
205
RETURN
31
RESET
Main Menu -
1) RESET
S E TUP
¨ç Select RESET .
CAMERA ID
OFF
Press MENU button.
LENS
DC ¢×
The screen on the bottom appears.
SHUTTER
FIXED ¢×
WHITE BAL.
ATW
OFF
FUNCTION
¢×
DC ¢×
¨è Select YES or NO .
ADJUST
¢×
FIXED ¢×
LANGUAGE
ENGLISH
ATW
RESET
¢×
¨é Select YES to reset your camera
¢×
EXIT
¢×
to default factory condition
ENGLISH
¢×
LOA D DE FAU LT
YES
NO
H D 7 3 X
BLC, AGC
ON / OFF (Level Adjustable)
PAL
Day & Night
Auto (ICR)
Privacy
ON / OFF (4 Programmable Zone)
752(H) x 582(V)
Mirror
ON / OFF (Horizontal)
Gamma
User / 0.5 ~ 1.0 Adjustable
Motion Detection
ON / OFF (64 Programmable Zone)
Contrast
0 ~ 255 (Level Adjustable)
Sharpness
0 ~ 31 (Level Adjustable)
Applicable Lens
DC Iris
Supply Voltage
12VDC (10V~15V)
Power Consumption
Max. 4.5W / 360mA
1/50~100,000
Operating Temperature
-10¡É~+50¡É (Recommendation: -5¡É~+40¡É)
Storage Temperature
-20¡É~+60¡É
Dome Size (Ø)
100 mm
Weight
Approx. 844g
. Memo
3-Axis
33
35
37
39
Advertisement
