Honeywell HCD95534 Quick Install Manual

HCD95534/X Camera Quick Install Guide

Important Safety Information

• Read and keep these instructions.
• Heed all warnings and follow all instructions.
• Do not use this apparatus near water.
• Clean only with dry cloth.
• Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus.
Installation
The HCD95534/X camera is designed for installation on a wall or ceiling. The
HCD95534/X is weather sealed for indoor or outdoor locations.

Attaching the Camera

1. Position the camera to the desired mounting location on a solid, flat surface (for
example, a crossbeam).
2. Using the supplied mounting template, mark the four screw holes for installation
and screw in the camera.
The mounting bracket can be separated from the camera housing for easier
installation. This is done by unscrewing and removing the thumb screw on the bracket
(see Figure 1).
Figure 1 Mounting Bracket
thumb screw
water drain notch
Note To ensure a waterproof installation, the notch in the camera base that the
power and video connections exit through should be facing down.
Positioning the Camera
Caution Do not swivel and position the camera without the mounting bracket
firmly in place.
Loosen the thumb screws and move the camera into position. Swivel the camera to
capture the desired field of view. Tighten the thumb screws to set the position.
Lens Setup
Adjusting the Zoom and Focus of the Lens
The zoom and focus adjustment is accessible at the underside front end of the camera
housing.
Figure 2 Lens Controllerr
Use a flathead screwdriver to adjust the zoom and/or focus. To adjust the focus, turn
the focus screw counter-clockwise for near focus and clockwise for far.
Document 800-00813 – Rev A – 11/08

Camera Settings

Camera Functions

Legend
# Description
1 Video-test monitor output connector
2 LUX-level adjustment DIP switches. Only one switch should be on at a time. They
modify the point at which the lux threshold (level of light) changes the mode of
operation (color or B/W).
STEP
1
2
3
4
3 LED-level adjustment screw. Increase (turn clockwise) or lower (turn counter-
clockwise) the IR LED brightness in night (B/W) mode.
4 Camera OSD control (four position plus center push)

Connecting the Camera

1. Connect the BNC video output connector to the video-in connector on your
monitor or video recorder.
2. Connect the camera to a power supply appropriate for your installation (12 VDC
or 24 VAC).
Programming

OSD Menu Structure

The HCD95534X menu system consists of one main SETUP menu (see
easy camera programming.
Press down on the SETUP (MENU) control (see
1
LENS
2
SHUTTER
3
WHITE BAL.
Zoom adjustment screw
4
BACKLIGHT
5
AGC
6
DNR
7
DSS
8
SPECIAL!
9
EXIT MENU
Focus adjustment screw
Figure 3 Camera Controller
VIDEO-TEST
1
LUX LEVEL
UP
4 LEFT RIGHT 2
DOWN
SETUP (MENU)
PUSH DOWN
3
LED-LEVEL
Color to B/W (LED on) B/W to Color (LED off)
11–12 lux 12–13 lux
8–9 lux 10–11 lux
6–7 lux 7–8 lux
1–3 lux 3–5 lux
Press this control
UP, DOWN
LEFT, RIGHT
SETUP (MENU)
Figure 4 Menu Structure
<<SETUP MENU>>
DC!
– – –
ATW
OFF
SETUP
MIDDLE!
MENU
MIDDLE
OFF
LENS
SHUTTER
WHITE BAL.
BACKLIGHT
SETUP
MENU
AGC
DNR
DSS
SPECIAL!
EXIT MENU
ON
1 STEP
2 STEP
3 STEP
4 STEP
To do this
Select a new item
Select a menu item
Access a submenu
Figure 4) for
Figure 3) to display the SETUP menu.
DC! , VIDEO, MANUAL
FLK, ESC! , MANUAL
ATW, MANUAL! , AWC!
OFF, LOW, MIDDLE, HIGH
OFF, LOW! , MIDDLE! , HIGH!
OFF, LOW, MIDDLE, HIGH
!
OFF, AUTO
! indicates submenus