Installer Setup; Installer Setup Functions - Honeywell FocusPRO 5000 Series Installer's Manual

InSTalleR SeTuP

FocusPRO 5000 Series
®
1. To begin, press and hold the s and FAN buttons until
the display changes.
2. Press s or t to change settings.
Function Setting
1
0
Done Next
3. Press NEXT to advance to the next function.
4. Press DONE to exit and save settings.
5. Proceed to Installer Setup Functions on page 4.
2
FocusPRO 6000 Series
®
1. To begin, press and hold the s and FAN buttons until
the display changes.
2. Press s or t to change settings.
Function Setting
1
0
Done Next
3. Press NEXT to advance to the next function.
4. Press DONE to exit and save settings.
5. Proceed to Installer Setup Functions on page 4.
3

InSTalleR SeTuP FuncTIOnS

Available option and default settings vary by thermostat.
Table 1. Installer Setup
Setup functions Setting & Options
(factory default in bold)
1 System type 0 1 heat / 1 cool Conv.
1 1 heat / 1 cool heat
pump (no Aux. heat)
2 Heat only (2-wire, 3-wire
zone valves [Series 20],
and normally open zone
valves)
3 Heat only with fan
4 Cool only
5 2 heat / 1 cool heat
pump (with Aux. heat)
6 2 heat / 2 cool Conv.
7 2 heat / 1 cool Conv.
8 1 heat / 2 cool Conv.
9 2 heat / 2 cool heat pump
(no Aux. heat)
10 3 heat / 2 cool heat
pump (with Aux. heat)
2 Changeover valve 0 Controls valve in cooling
(O/B terminal) 1 Controls valve in heating
3 Fan control 0 Gas/Oil heat (equipment
(heating) controls heating fan)
1 Electric furnace (thermo-
stat controls heating fan)
5 First stage heat 5 Gas or oil furnaces of
cycle rate less than 90%
efficiency
1 Steam or gravity
3 Hot water systems or fur-
naces of 90%+ efficiency
9 Electric furnaces
[Other options: 1–12]
6 Second stage 5 Gas or oil furnaces of
heat/Aux heat less than 90% efficiency
cycle rate 1 Steam or gravity
3 Hot water systems or fur-
naces of 90%+ efficiency
9 Electric furnaces
[Other options: 1–12]
7 Auxiliary heat 5 Gas or oil furnaces of
cycle rate less than 90% efficiency
1 Steam or gravity
3 Hot water systems or fur-
naces of 90%+ efficiency
9 Electric furnaces
[Other options: 1–12]
4
Table 1. Installer Setup
Setup functions Setting & Options
(factory default in bold)
8 Emergency heat 9 Electric emergency heat
cycle rate 1 Steam or gravity
3 Hot water systems or fur-
naces of 90%+ efficiency
5 Gas or oil furnaces of
less than 90% efficiency
[Other options: 1–12]
9 First stage 3 Recommended
compressor cycle [Other options: 1–6]
rate
10 Second stage 3 Recommended
compressor cycle [Other options: 1–6]
rate
12 Manual/Auto 0 Manual changeover
changeover (Heat/Cool/Off)
1 Auto changeover (Heat/
Cool/Auto/Off)
2 Auto changeover only
(Auto)
13 Adaptive Intel- 1 On
ligent Recovery 0 Off
TM
14 Temperature 0 Fahrenheit
display 1 Celsius
15 Compressor 5 5-minute compressor
protection off time
[Other options: 0–4
minutes]
16 Schedule format 0 5/2 (weekdays
and weekends
programmable)
1 5/1/1 (weekdays,
Saturday, and Sunday
programmable)
26 Auxiliary heat 0 Comfort
control 1 Economy
27 Heat temperature 90 Max. heat temperature
range stops setting is 90°F (32°C)
[Other options: 40–89°F
(4.5°C to 32°C)]
28 Cool temperature 50 Min. cool temperature
range stop setting is 50°F (10°C)
[Other options: 51–99°F
(10.5°C to 37°C)]
Functions 13 and 16 only available on the 6000 series;
function 26 only available on the 5000 series
5
Printed in U.S.A. on recycled
paper containing at least 10%
post-consumer paper fibers.
Automation and Control Solutions
Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422
Honeywell Limited-Honeywell Limitée
35 Dynamic Drive
Toronto, Ontario M1V 4Z9
http://yourhome.honeywell.com
® U.S. Registered Trademark
© 2006 Honeywell International Inc.
US Patent No. 6595430, D509151; other
Patents Pending. All Rights Reserved
69-2026 M.S. 09-06