Page 1 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference Cisco IOS Release 12.2(50)SE March 2009 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883...
Page 2 Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental. Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference ©2007–2009 Cisco Systems, Inc. All rights reserved.
Page 3: Table Of Contents
Global Configuration Mode Interface Configuration Mode config-vlan Mode VLAN Configuration Mode Line Configuration Mode Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands C H A P T E R aaa accounting dot1x aaa authentication dot1x aaa authorization network...
Page 4 2-76 clear ip dhcp snooping 2-78 clear ipc 2-80 clear ipv6 dhcp conflict 2-81 clear l2protocol-tunnel counters 2-82 clear lacp 2-83 clear logging 2-84 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference OL-13271-03...
Page 5 2-130 dot1x fallback 2-131 dot1x guest-vlan 2-132 dot1x host-mode 2-134 dot1x initialize 2-135 dot1x mac-auth-bypass 2-136 dot1x max-reauth-req 2-138 dot1x max-req 2-139 dot1x pae 2-140 dot1x port-control 2-141 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference OL-13271-03...
Page 6 2-200 ip arp inspection vlan logging 2-201 ip dhcp snooping 2-203 ip dhcp snooping binding 2-204 ip dhcp snooping database 2-206 ip dhcp snooping information option 2-208 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference OL-13271-03...
Page 7 2-255 ipv6 dhcp pool 2-257 ipv6 dhcp server 2-259 ipv6 mld snooping 2-261 ipv6 mld snooping last-listener-query-count 2-263 ipv6 mld snooping last-listener-query-interval 2-265 ipv6 mld snooping listener-message-suppression 2-267 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference OL-13271-03...
Page 8 2-323 mls qos 2-325 mls qos aggregate-policer 2-327 mls qos cos 2-329 mls qos dscp-mutation 2-331 mls qos map 2-333 mls qos queue-set output buffers 2-337 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference viii OL-13271-03...
Page 9 2-385 permit (MAC access-list configuration) 2-390 police 2-393 police aggregate 2-395 policy-map 2-397 port-channel load-balance 2-400 priority-queue 2-402 private-vlan 2-404 private-vlan mapping 2-407 queue-set 2-409 radius-server dead-criteria 2-410 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference OL-13271-03...
Page 10 2-469 show controllers utilization 2-471 show diagnostic 2-473 show dot1q-tunnel 2-478 show dot1x 2-479 show dtp 2-483 show eap 2-485 show energywise 2-488 show env 2-492 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference OL-13271-03...
Page 11 2-564 show ipv6 route updated 2-566 show l2protocol-tunnel 2-568 show lacp 2-571 show link state group 2-575 show location 2-577 show logging 2-580 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference OL-13271-03...
Page 12 2-638 show policy-map 2-641 show port-security 2-643 show sdm prefer 2-646 show setup express 2-650 show spanning-tree 2-651 show storm-control 2-659 show switch 2-661 show system mtu 2-666 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference OL-13271-03...
Page 13 2-725 spanning-tree mst port-priority 2-726 spanning-tree mst pre-standard 2-728 spanning-tree mst priority 2-729 spanning-tree mst root 2-730 spanning-tree port-priority 2-732 spanning-tree portfast (global configuration) 2-734 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference xiii OL-13271-03...
Page 14 2-794 switchport trunk 2-796 switchport voice detect 2-799 switchport voice vlan 2-800 system env temperature threshold yellow 2-802 system mtu 2-804 test cable-diagnostics tdr 2-806 traceroute mac 2-807 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference OL-13271-03...
Page 15 2-842 vmps server 2-843 vtp (global configuration) 2-845 vtp (VLAN configuration) 2-849 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands A P P E N D I X boot copy delete flash_init A-10 format...
Page 16 A-23 A-24 type A-27 unset A-28 version A-30 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands A P P E N D I X debug auto qos debug backup debug cisp debug dot1x debug dtp debug eap...
Page 17 B-65 debug platform tcam B-66 debug platform udld B-69 debug platform vlan B-70 debug pm B-71 debug port-security B-73 debug qos-manager B-74 debug spanning-tree B-75 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference xvii OL-13271-03...
Page 18 B-90 debug udld B-92 debug vqpc B-94 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Show Platform Commands A P P E N D I X show platform acl show platform backup interface show platform configuration show platform dl...
Page 19 C-43 show platform tcam C-45 show platform vlan C-48 Acknowledgments for Open-Source Software A P P E N D I X N D E X Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference OL-13271-03...
Page 20 Contents Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference OL-13271-03...
Page 21 This guide is for the networking professional using the Cisco IOS command-line interface (CLI) to manage the standalone Cisco Catalyst Blade Switch 3130 for Dell or blade switch stack, referred to as the switch. Before using this guide, you should have experience working with the Cisco IOS commands and the switch software features.
Page 22: Related Publications
• Device manager online help (available on the switch) • Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Hardware Installation Guide • Cisco Catalyst Blade Switch 3130 for Dell and Cisco Catalyst Blade Switch 3032 for Dell Getting...
Page 23: Obtaining Documentation And Submitting A Service Request
The RSS feeds are a free service and Cisco currently supports RSS version 2.0. Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference xxiii...
Page 24 Preface Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference xxiv OL-13271-03...
Page 25: Accessing The Switch
3130 and 3032 for Dell Debug Commands.” For information on the show platform commands, see Appendix C, “Cisco Catalyst Blade Switch 3130 and 3032 for Dell Show Platform Commands.” more information on Cisco IOS Release 12.2, see the Cisco IOS Release 12.2 Command Summary.
Page 26: C H A P T E R 1 Using The Command-Line Interface
To exit to global configuration mode, Switch(config-vlan)# enter the vlan vlan-id command. enter the exit command. To return to privileged EXEC mode, enter the end command, or press Ctrl-Z. Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference OL-13271-03...
Page 27: User Exec Mode
The supported commands can vary depending on the version of software in use. To display a comprehensive list of commands, enter a question mark (?) at the prompt. Switch# ? To return to user EXEC mode, enter the disable privileged EXEC command. Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference OL-13271-03...
Page 28: Global Configuration Mode
To exit interface configuration mode and to return to global configuration mode, enter the exit command. To exit interface configuration mode and to return to privileged EXEC mode, enter the end command, or press Ctrl-Z. Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference OL-13271-03...
Page 29: Config-Vlan Mode
EXEC mode. When you enter exit or apply, the configuration is saved in the VLAN database; configuration from VLAN configuration mode cannot be saved in the switch configuration file. Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference OL-13271-03...
Page 30: Line Configuration Mode
To exit line configuration mode and to return to global configuration mode, use the exit command. To exit line configuration mode and to return to privileged EXEC mode, enter the end command, or press Ctrl-Z. Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference OL-13271-03...
Page 31: Aaa Accounting Dot1X
TACACS+ hosts. • The group keyword is optional when you enter it after the broadcast group and group keywords. You can enter more than optional group keyword. Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference OL-13271-03...
Page 32: C H A P T E R 2 Cisco Catalyst Blade Switch 3130 And 3032 For Dell Cisco Ios Commands
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands aaa accounting dot1x radius (Optional) Enable RADIUS authorization. tacacs+ (Optional) Enable TACACS+ accounting. Defaults AAA accounting is disabled. Command Modes Global configuration Command History Release Modification 12.2(40)EX1...
Page 33: Aaa Authentication Dot1X
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands aaa authentication dot1x aaa authentication dot1x Use the aaa authentication dot1x global configuration command on the switch stack or on a standalone switch to specify the authentication, authorization, and accounting (AAA) method to use on ports complying with the IEEE 802.1x authentication.
Page 34: Aaa Authentication Dot1X
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands aaa authentication dot1x You can verify your settings by entering the show running-config privileged EXEC command. Related Commands Command Description aaa new-model Enables the AAA access control model. For syntax information, see the Cisco IOS Security Command Reference, Release 12.2 >...
Page 35: Aaa Authorization Network
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands aaa authorization network aaa authorization network Use the aaa authorization network global configuration command on the switch stack or on a standalone switch to the configure the switch to use user-RADIUS authorization for all network-related service requests, such as IEEE 802.1x per-user access control lists (ACLs) or VLAN assignment.
Page 36 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands action action Use the action access-map configuration command on the switch stack or on a standalone switch to set the action for the VLAN access map entry. Use the no form of this command to return to the default setting.
Page 37: Action
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands action Related Commands Command Description access-list {deny | permit} Configures a standard numbered ACL. For syntax information, select Cisco IOS IP Command Reference, Volume 1 of 3:Addressing and Services, Release 12.2 >...
Page 38 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands archive copy-sw archive copy-sw Use the archive copy-sw privileged EXEC command on the stack master to copy the running image from the flash memory on one stack member to the flash memory on one or more other stack members.
Page 39: Archive Copy-Sw
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands archive copy-sw To successfully use the archive copy-sw privileged EXEC command, you must have downloaded from Note a TFTP server the images for both the stack member switch being added and the stack master. You use the archive download-sw privileged EXEC command to perform the download.
Page 40 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands archive copy-sw Examples This example shows how to copy the running image from stack member 6 to stack member 8: Switch# archive copy-sw /destination-system 8 6...
Page 41 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands archive download-sw archive download-sw Use the archive download-sw privileged EXEC command on the switch stack or on a standalone switch to download a new image from a TFTP server to the switch or switch stack and to overwrite or keep the existing image.
Page 42: Archive Download-Sw
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands archive download-sw source-url1 [sourceurl2 The source URLs for the software images. sourceurl3 sourceurl4] On a standalone switch, enter one source URL for the software image that the switch supports.
Page 43 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands archive download-sw Command History Release Modification 12.2(40)EX1 This command was introduced. Usage Guidelines Use the /allow-feature-upgrade option to allow installation of an image with a different feature set, for example, upgrading from the IP base feature set to the IP services feature.
Page 44 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands archive download-sw This example shows how to keep the old software version after a successful download: Switch# archive download-sw /leave-old-sw tftp://172.20.129.10/test-image.tar This example specifies the location of two tar images without having to specify the path each time: Switch# archive download-sw tftp://10.1.1.10/...
Page 45: Archive Tar
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands archive tar archive tar Use the archive tar privileged EXEC command on the switch stack or on a standalone switch to create a tar file, list files in a tar file, or extract the files from a tar file.
Page 46: Archive Tar
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands archive tar /table source-url Display the contents of an existing tar file to the screen. For source-url, specify the source URL alias for the local or network file system.
Page 47 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands archive tar Command Modes Privileged EXEC Command History Release Modification 12.2(40)EX1 This command was introduced. Usage Guidelines Filenames and directory names are case sensitive. Image names are case sensitive.
Page 48 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands archive upload-sw archive upload-sw Use the archive upload-sw privileged EXEC command on the switch stack or on a standalone switch to upload an existing switch image to a server.
Page 49: Archive Upload-Sw
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands archive upload-sw Usage Guidelines You must specify that the /source-system-num option uses the /version option. The options together upload the specified image, not the running image, of a specific stack member.
Page 50 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands arp access-list arp access-list Use the arp access-list global configuration command on the switch stack or on a standalone switch to define an Address Resolution Protocol (ARP) access control list (ACL) or to add clauses to the end of a previously defined list.
Page 51: Arp Access-List
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands arp access-list Examples This example shows how to define an ARP access list and to permit both ARP requests and ARP responses from a host with an IP address of 1.1.1.1 and a MAC address of 0000.0000.abcd: Switch(config)# arp access-list static-hosts Switch(config-arp-nacl)# permit ip host 1.1.1.1 mac host 00001.0000.abcd...
Page 52 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication control-direction authentication control-direction Use the authentication control-direction interface configuration command to configure the port mode as unidirectional or bidirectional. Use the no form of this command to return to the default setting.
Page 53: Authentication Control-Direction
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication control-direction Command Description authentication Enable or disables reauthentication on a port. periodic authentication Enables manual control of the port authorization state. port-control authentication Adds an authentication method to the port-priority list.
Page 54: Authentication Event
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication event authentication event Use the authentication event interface configuration command to set the actions for specific authentication events on the port. authentication event fail {[action [authorize vlan vlan-id | next-method] {| retry {retry count}]}...
Page 55: Authentication Event
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication event For server-dead events: When the switch moves to the critical-authentication state, only new hosts trying to authenticate are • moved to the critical-authentication VLAN. Authenticated hosts remain in the authenticated VLAN, and the reauthentication timers are disabled.
Page 56 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication event You cannot configure an internal VLANs for Layer 3 ports as a restricted VLAN. You cannot specify • the same VLAN as a restricted VLAN and as a voice VLAN.
Page 57: Authentication Fallback
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication fallback authentication fallback Use the authentication fallback interface configuration command to configure a port to use web authentication as a fallback method for clients that do not support IEEE 802.1x authentication. To return to the default setting, use the no form of this command.
Page 58 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication fallback Command Description authentication Enables manual control of the port authorization state. port-control authentication Adds an authentication method to the port-priority list. priority authentication timer Configures the timeout and reauthentication parameters for an 802.1x-enabled port.
Page 59: Authentication Host-Mode
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication host-mode authentication host-mode Use the authentication host-mode interface configuration command to set the authorization manager mode on a port. authentication host-mode [multi-auth | multi-domain | multi-host | single-host]...
Page 60 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication host-mode Switch(config)# authentication host-mode single-host You can verify your settings by entering the show authentication privileged EXEC command. Related Commands Command Description authentication Configures the port mode as unidirectional or bidirectional.
Page 61: Authentication Open
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication open authentication open Use the authentication open interface configuration command to enable or disable open access on a port. Use the no form of this command to disable open access.
Page 62 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication open Command Description authentication timer Configures the timeout and reauthentication parameters for an 802.1x-enabled port. authentication Configures the violation modes that occur when a new device connects to a...
Page 63: Authentication Order
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication order authentication order Use the authentication order interface configuration command to set the order of authentication methods used on a port. authentication order [dot1x | mab] {webauth}...
Page 64 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication order Related Commands Command Description authentication Configures the port mode as unidirectional or bidirectional. control-direction authentication event Sets the action for specific authentication events. authentication...
Page 65: Authentication Periodic
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication periodic authentication periodic Use the authentication periodic interface configuration command to enable or disable reauthentication on a port. Enter the no form of this command to disable reauthentication.
Page 66 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication periodic Command Description authentication timer Configures the timeout and reauthentication parameters for an 802.1x-enabled port. authentication Configures the violation modes that occur when a new device connects to a...
Page 67: Authentication Port-Control
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication port-control authentication port-control Use the authentication port-control interface configuration command to enable manual control of the port authorization state. Use the no form of this command to return to the default setting.
Page 68 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication port-control Switched Port Analyzer (SPAN) and Remote SPAN (RSPAN) destination ports—You can enable • IEEE 802.1x authentication on a port that is a SPAN or RSPAN destination port. However, IEEE 802.1x authentication is disabled until the port is removed as a SPAN or RSPAN destination.
Page 69: Authentication Priority
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication priority authentication priority Use the authentication priority interface configuration command to add an authentication method to the port-priority list. auth priority [dot1x | mab] {webauth}...
Page 70 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication priority This example shows how to set MAC authentication Bypass (MAB) as the first authentication method and web authentication as the second authentication method: Switch(config)# authentication priority mab webauth You can verify your settings by entering the show authentication privileged EXEC command.
Page 71: Authentication Timer
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication timer authentication timer Use the authentication timer interface configuration command to configure the timeout and reauthentication parameters for an 802.1x-enabled port. authentication timer {{[inactivity | reauthenticate] [server | am]} {restart value}}...
Page 72 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication timer Related Commands Command Description authentication Configures the port mode as unidirectional or bidirectional. control-direction authentication event Sets the action for specific authentication events. authentication...
Page 73: Authentication Violation
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication violation authentication violation Use the authentication violation interface configuration command to configure the violation modes that occur when a new device connects to a port or when a new device connects to a port after the maximum number of devices are connected to that port.
Page 74 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands authentication violation Command Description authentication Configures a port to use web authentication as a fallback method for clients fallback that do not support IEEE 802.1x authentication.
Page 75: Auto Qos Voip
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands auto qos voip auto qos voip Use the auto qos voip interface configuration command on the switch stack or on a standalone switch to automatically configure quality of service (QoS) for voice over IP (VoIP) within a QoS domain. Use the no form of this command to return to the default setting.
Page 76 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands auto qos voip Table 2-2 shows the generated auto-QoS configuration for the ingress queues. Table 2-2 Auto-QoS Configuration for the Ingress Queues Queue Weight Queue (Buffer)
Page 77 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands auto qos voip If this is the first port on which you have enabled auto-QoS, the auto-QoS-generated global configuration commands are executed followed by the interface configuration commands. If you enable auto-QoS on another port, only the auto-QoS-generated interface configuration commands for that port are executed.
Page 78 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands auto qos voip disabled, there is no concept of trusted or untrusted ports because the packets are not modified (the CoS, DSCP, and IP precedence values in the packet are not changed). Traffic is switched in pass-through mode (packets are switched without any rewrites and classified as best effort without any policing).
Page 79: Boot Auto-Copy-Sw
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands boot auto-copy-sw boot auto-copy-sw Use the boot auto-copy-sw global configuration command from the stack master to enable the automatic upgrade (auto-upgrade) process. It automatically upgrades a switch in version-mismatch (VM) mode by copying the running software image on any stack member or by copying a tar file image in switch stack flash memory.
Page 80 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands boot auto-copy-sw Related Commands Command Description show boot Displays the settings of the boot environment variables. show version Displays version information for the hardware and firmware.
Page 81: Boot Auto-Download-Sw
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands boot auto-download-sw boot auto-download-sw Use the boot auto-download-sw global configuration command on the switch stack to specify a URL pathname to use for the automatic software upgrades. Use the no form of this command to remove the software image.
Page 82 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands boot auto-download-sw Command History Release Modification 12.2(40)EX1 This command was introduced. Usage Guidelines This command specifies a URL path to use for automatic software upgrades. You can use this command to configure the URL for the master switch to access in case of version-mismatch.
Page 83: Boot Config-File
This command works properly only from a standalone switch in a stack. Filenames and directory names are case sensitive. This command changes the setting of the CONFIG_FILE environment variable. For more information, Appendix A, “Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands.” Related Commands Command...
Page 84: Boot Enable-Break
Note the MODE button on the switch front panel. This command changes the setting of the ENABLE_BREAK environment variable. For more information, see Appendix A, “Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands.” Related Commands Command...
Page 85: Boot Helper
This variable is used only for internal development and testing. Filenames and directory names are case sensitive. This command changes the setting of the HELPER environment variable. For more information, see Appendix A, “Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands.” Related Commands Command...
Page 86: Boot Helper-Config-File
This variable is used only for internal development and testing. Filenames and directory names are case sensitive. This command changes the setting of the HELPER_CONFIG_FILE environment variable. For more information, see Appendix A, “Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands.” Related Commands Command...
Page 87: Boot Manual
To boot up the system, use the boot boot loader command, and specify the name of the bootable image. This command changes the setting of the MANUAL_BOOT environment variable. For more information, see Appendix A, “Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands.” Related Commands Command...
Page 88: Boot Private-Config-File
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands boot private-config-file boot private-config-file Use the boot private-config-file global configuration command on a standalone switch to specify the filename that Cisco IOS uses to read and write a nonvolatile copy of the private configuration. Use the no form of this command to return to the default setting.
Page 89: Boot System
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands boot system boot system Use the boot system global configuration command on the switch stack or on a standalone switch to specify the Cisco IOS image to load during the next boot cycle. Use the no form of this command to return to the default setting.
Page 90 The boot system command is automatically manipulated to load the downloaded image. This command changes the setting of the BOOT environment variable. For more information, see Appendix A, “Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands.” Related Commands Command...
Page 91: Channel-Group
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands channel-group channel-group Use the channel-group interface configuration command on the switch stack or on a standalone switch to assign an Ethernet port to an EtherChannel group, to enable an EtherChannel mode, or both. Use the no form of this command to remove an Ethernet port from an EtherChannel group.
Page 92 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands channel-group Defaults No channel groups are assigned. No mode is configured. Command Modes Interface configuration Command History Release Modification 12.2(40)EX1 This command was introduced. Usage Guidelines For Layer 2 EtherChannels, you do not have to create a port-channel interface first by using the interface port-channel global configuration command before assigning a physical port to a channel group.
Page 93 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands channel-group Do not configure a port that is an active or a not-yet-active member of an EtherChannel as an IEEE 802.1x port. If you try to enable IEEE 802.1x authentication on an EtherChannel port, an error message appears, and IEEE 802.1x authentication is not enabled.
Page 94 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands channel-group Related Commands Command Description channel-protocol Restricts the protocol used on a port to manage channeling. interface port-channel Accesses or creates the port channel. show etherchannel Displays EtherChannel information for a channel.
Page 95: Channel-Protocol
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands channel-protocol channel-protocol Use the channel-protocol interface configuration command on the switch stack or on a standalone switch to restrict the protocol used on a port to manage channeling. Use the no form of this command to return to the default setting.
Page 96: Cisp Enable
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands cisp enable cisp enable Use the cisp enable global configuration command to enable Client Information Signalling Protocol (CISP) on a switch so that it acts as an authenticator to a supplicant switch.
Page 97: Class
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands class class Use the class policy-map configuration command on the switch stack or on a standalone switch to define a traffic classification match criteria (through the police, set, and trust policy-map class configuration commands) for the specified class-map name.
Page 98 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands class Examples This example shows how to create a policy map called policy1. When attached to the ingress direction, it matches all the incoming traffic defined in class1, sets the IP Differentiated Services Code Point (DSCP) to 10, and polices the traffic at an average rate of 1 Mb/s and bursts at 20 KB.
Page 99: Class-Map
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands class-map class-map Use the class-map global configuration command on the switch stack or on a standalone switch to create a class map to be used for matching packets to the class whose name you specify and to enter class-map configuration mode.
Page 100 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands class-map If you enter the match-all or match-any keyword, you can only use it to specify an extended named access control list (ACL) with the match access-group acl-index-or-name class-map configuration command.
Page 101: Clear Dot1X
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear dot1x clear dot1x Use the clear dot1x privileged EXEC command on the switch stack or on a standalone switch to clear IEEE 802.1x information for the switch or for the specified port.
Page 102: Clear Eap
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear eap clear eap Use the clear eap privileged EXEC command on the switch stack or on a standalone switch to clear Extensible Authentication Protocol (EAP) session information for the switch or for the specified port.
Page 103 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear energywise neighbors clear energywise neighbors Use the clear energywise neighbors privileged EXEC command to delete the EnergyWise neighbor tables. clear energywise neighbors Syntax Description This command has no arguments or keywords.
Page 104: Clear Errdisable Interface
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear errdisable interface clear errdisable interface Use the clear errdisable interface privileged EXEC command on the switch stack or on a standalone switch to re-enable a VLAN that was error disabled.
Page 105: Clear Ip Arp Inspection Log
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear ip arp inspection log clear ip arp inspection log Use the clear ip arp inspection log privileged EXEC command on the switch stack or on a standalone switch to clear the dynamic Address Resolution Protocol (ARP) inspection log buffer.
Page 106: Clear Ip Arp Inspection Statistics
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear ip arp inspection statistics clear ip arp inspection statistics Use the clear ip arp inspection statistics privileged EXEC command on the switch stack or on a standalone switch to clear the dynamic Address Resolution Protocol (ARP) inspection statistics.
Page 107: Clear Ip Dhcp Snooping
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear ip dhcp snooping clear ip dhcp snooping Use the clear ip dhcp snooping privileged EXEC command on the switch stack or on a standalone switch to clear the DHCP binding database agent statistics or the DHCP snooping statistics counters.
Page 108 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear ip dhcp snooping Related Commands Command Description ip dhcp snooping Enables DHCP snooping on a VLAN. ip dhcp snooping database Configures the DHCP snooping binding database agent or the binding file.
Page 109: Clear Ip Dhcp Snooping
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear ip dhcp snooping clear ip dhcp snooping Use the clear ip dhcp snooping privileged EXEC command on the switch stack or on a standalone switch to clear the DHCP snooping binding database, the DHCP snooping binding database agent statistics, or the DHCP snooping statistics counters.
Page 110 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear ip dhcp snooping Related Commands Command Description ip dhcp snooping Enables DHCP snooping on a VLAN. ip dhcp snooping database Configures the DHCP snooping binding database agent or the binding file.
Page 111: Clear Ipc
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear ipc clear ipc Use the clear ipc privileged EXEC command on the switch stack or on a standalone switch to clear Interprocess Communications Protocol (IPC) statistics.
Page 112: Clear Ipv6 Dhcp Conflict
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear ipv6 dhcp conflict clear ipv6 dhcp conflict Use the clear ipv6 dhcp conflict privileged EXEC command on the switch stack or on a standalone switch to clear an address conflict from the Dynamic Host Configuration Protocol for IPv6 (DHCPv6) server database.
Page 113: Clear L2Protocol-Tunnel Counters
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear l2protocol-tunnel counters clear l2protocol-tunnel counters Use the clear l2protocol-tunnel counters privileged EXEC command on the switch stack or on a standalone switch to clear the protocol counters in protocol tunnel ports.
Page 114: Clear Lacp
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear lacp clear lacp Use the clear lacp privileged EXEC command on the switch stack or on a standalone switch to clear Link Aggregation Control Protocol (LACP) channel-group counters.
Page 115: Clear Logging
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear logging clear logging Use the clear logging privileged EXEC command on the switch stack or on a standalone switch to clear all of the on-board failure logging (OBFL) data except for the uptime and CLI-command information stored in the flash memory.
Page 116: Clear Mac Address-Table
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear mac address-table clear mac address-table Use the clear mac address-table privileged EXEC command on the switch stack or on a standalone switch to delete from the MAC address table a specific dynamic address, all dynamic addresses on a particular interface, all dynamic addresses on stack members, or all dynamic addresses on a particular VLAN.
Page 117: Clear Mac Address-Table Move Update
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear mac address-table move update clear mac address-table move update Use the clear mac address-table move update privileged EXEC command on the switch stack or on a standalone switch to clear the MAC address table move-update counters.
Page 118: Clear Nmsp Statistics
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear nmsp statistics clear nmsp statistics Use the clear nmsp statistics privileged EXEC command to clear the Network Mobility Services Protocol (NMSP) statistics. This command is available only when your switch is running the cryptographic (encrypted) software image.
Page 119: Clear Pagp
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear pagp clear pagp Use the clear pagp privileged EXEC command on the switch stack or on a standalone switch to clear Port Aggregation Protocol (PAgP) channel-group information.
Page 120: Clear Port-Security
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear port-security clear port-security Use the clear port-security privileged EXEC command on the switch stack or on a standalone switch to delete from the MAC address table all secure addresses or all secure addresses of a specific type (configured, dynamic, or sticky) on the switch or on an interface.
Page 121 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear port-security This example shows how to remove all the dynamic secure addresses learned on a specific interface: Switch# clear port-security dynamic interface gigabitethernet1/0/1 This example shows how to remove all the dynamic secure addresses from the address table:...
Page 122: Clear Spanning-Tree Counters
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear spanning-tree counters clear spanning-tree counters Use the clear spanning-tree counters privileged EXEC command on the switch stack or on a standalone switch to clear the spanning-tree counters.
Page 123: Clear Spanning-Tree Detected-Protocols
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear spanning-tree detected-protocols clear spanning-tree detected-protocols Use the clear spanning-tree detected-protocols privileged EXEC command on the switch stack or on a standalone switch to restart the protocol migration process (force the renegotiation with neighboring switches) on all interfaces or on the specified interface.
Page 124: Clear Vmps Statistics
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear vmps statistics clear vmps statistics Use the clear vmps statistics privileged EXEC command on the switch stack or on a standalone switch to clear the statistics maintained by the VLAN Query Protocol (VQP) client.
Page 125: Clear Vtp Counters
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands clear vtp counters clear vtp counters Use the clear vtp counters privileged EXEC command on the switch stack or on a standalone switch to clear the VLAN Trunking Protocol (VTP) and pruning counters.
Page 126: Copy Logging Onboard
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands copy logging onboard copy logging onboard Use the copy logging onboard privileged EXEC command on the switch stack or on a standalone switch to copy on-board failure logging (OBFL) data to the local network or a specific file system.
Page 127 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands copy logging onboard Command History Release Modification 12.2(40)EX1 This command was introduced. Usage Guidelines For information about OBFL, see the hw-module command. Examples This example shows how to copy the OBFL data messages to the obfl_file file on the flash file system...
Page 128: Define Interface-Range
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands define interface-range define interface-range Use the define interface-range global configuration command on the switch stack or on a standalone switch to create an interface-range macro. Use the no form of this command to delete the defined macro.
Page 129 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands define interface-range For physical interfaces: stack member is the number used to identify the switch within the stack. The number ranges from 1 • to 9 and is assigned to the switch the first time the stack member initializes.
Page 130: Delete
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands delete delete Use the delete privileged EXEC command on the switch stack or on a standalone switch to delete a file or directory on the flash memory device.
Page 131: Deny (Arp Access-List Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands deny (ARP access-list configuration) deny (ARP access-list configuration) Use the deny Address Resolution Protocol (ARP) access-list configuration command on the switch stack or on a standalone switch to deny an ARP packet based on matches against the DHCP bindings. Use the no form of this command to remove the specified access control entry (ACE) from the access list.
Page 132 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands deny (ARP access-list configuration) Command History Release Modification 12.2(40)EX1 This command was introduced. Usage Guidelines You can add deny clauses to drop ARP packets based on matching criteria.
Page 133: Deny (Ipv6 Access-List Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands deny (IPv6 access-list configuration) deny (IPv6 access-list configuration) Use the deny command in IPv6 access list configuration mode on the switch stack or on a standalone switch to set deny conditions for an IPv6 access list.
Page 134 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands deny (IPv6 access-list configuration) host source-ipv6-address The source IPv6 host address for which to set deny conditions. This source-ipv6-address argument must be in the form documented in RFC 2373 where the address is specified in hexadecimal using 16-bit values between colons.
Page 135 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands deny (IPv6 access-list configuration) sequence value (Optional) Specify the sequence number for the access list statement. The acceptable range is from 1 to 4294967295. time-range name (Optional) Specify the time range that applies to the deny statement.
Page 136 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands deny (IPv6 access-list configuration) Usage Guidelines The deny (IPv6 access-list configuration mode) command is similar to the deny (IPv4 access-list configuration mode) command, but it is IPv6-specific.
Page 137 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands deny (IPv6 access-list configuration) router-solicitation time-exceeded unreachable Examples This example configures the IPv6 access list named CISCO and applies the access list to outbound traffic on a Layer 3 interface. The first deny entry in the list prevents all packets that have a destination TCP port number greater than 5000 from leaving the interface.
Page 138: Deny (Mac Access-List Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands deny (MAC access-list configuration) deny (MAC access-list configuration) Use the deny MAC access-list configuration command on the switch stack or on a standalone switch to prevent non-IP traffic from being forwarded if the conditions are matched. Use the no form of this command to remove a deny condition from the named MAC access list.
Page 139 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands deny (MAC access-list configuration) lsap lsap-number mask (Optional) Use the LSAP number (0 to 65535) of a packet with 802.2 encapsulation to identify the protocol of the packet.
Page 140 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands deny (MAC access-list configuration) Usage Guidelines You enter MAC-access list configuration mode by using the mac access-list extended global configuration command. If you use the host keyword, you cannot enter an address mask; if you do not use the host keyword, you must enter an address mask.
Page 141: Diagnostic Monitor
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands diagnostic monitor diagnostic monitor Use the diagnostic monitor global configuration command to configure health-monitoring diagnostic testing. Use the no form of this command to disable testing and to return to the default settings.
Page 142 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands diagnostic monitor threshold Configure the failure threshold. failure count Set the failure threshold count. The range for count is from 0 to 99. count Defaults Monitoring is disabled, and a failure threshold value is not set.
Page 143: Diagnostic Schedule
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands diagnostic schedule diagnostic schedule Use the diagnostic schedule global configuration command to configure the diagnostic test schedule. Use the no form of this command to remove the schedule.
Page 144 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands diagnostic schedule Usage Guidelines Use these guidelines when scheduling testing: name—Enter the show diagnostic content privileged EXEC command to display the test names in • the test ID list.
Page 145: Diagnostic Start
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands diagnostic start diagnostic start Use the diagnostic start privileged EXEC command to run an online diagnostic test. diagnostic start switch number test {name | test-id | test-id-range | all | basic | non-disruptive}...
Page 146 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands diagnostic start When specifying a test name, use the show diagnostic content privileged EXEC command to display the test ID list. To specify test 3 by using the test name, enter the diagnostic start switch number test TestPortAsicCam privileged EXEC command.
Page 147 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands diagnostic start This message appears if the configured test can cause a stack partition: Switch 6: Running test(s) 2 will cause the switch under test to reload after completion of the test list.
Page 148: Dot1X
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x dot1x Use the dot1x global configuration command on the switch stack or on a standalone switch to globally enable IEEE 802.1x authentication. Use the no form of this command to return to the default setting.
Page 149 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x Examples This example shows how to globally enable IEEE 802.1x authentication on a switch: Switch(config)# dot1x system-auth-control This example shows how to globally enable the optional guess VLAN behavior on the switch:...
Page 150: Dot1X Auth-Fail Max-Attempts
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x auth-fail max-attempts dot1x auth-fail max-attempts Use the dot1x auth-fail max-attempts interface configuration command on the switch stack or on a standalone switch to configure the maximum allowable authentication attempts before a port is moved to the restricted VLAN.
Page 151 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x auth-fail max-attempts Related Commands Command Description dot1x auth-fail vlan [vlan id] Enables the optional restricted VLAN feature. dot1x max-reauth-req [count] Sets the maximum number of times that the switch restarts the authentication process before a port changes to the unauthorized state.
Page 152: Dot1X Auth-Fail Vlan
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x auth-fail vlan dot1x auth-fail vlan Use the dot1x auth-fail vlan interface configuration command on the switch stack or on a standalone switch to enable the restricted VLAN on a port. To return to the default setting, use the no form of this command.
Page 153 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x auth-fail vlan You cannot configure a VLAN to be both a restricted VLAN and a voice VLAN. If you do this, a syslog message is generated.
Page 154: Dot1X Control-Direction
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x control-direction dot1x control-direction Use the dot1x control-direction interface configuration command to enable the IEEE 802.1x authentication with the wake-on-LAN (WoL) feature and to configure the port control as unidirectional or bidirectional.
Page 155 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x control-direction If you enter the dot1x control-direction in interface configuration command to enable unidirectional control, this appears in the show dot1x all command output: ControlDirection...
Page 156: Dot1X Credentials (Global Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x credentials (global configuration) dot1x credentials (global configuration) Use the dot1x credentials global configuration command to configure a profile on a supplicant switch. dot1x credentials profile...
Page 157: Dot1X Critical (Global Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x critical (global configuration) dot1x critical (global configuration) Use the dot1x critical global configuration command on the switch stack or on a standalone switch to configure the parameters for the inaccessible authentication bypass feature, also referred to as critical authentication or the authentication, authorization, and accounting (AAA) fail policy.
Page 158 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x critical (global configuration) Related Commands Command Description dot1x critical (interface Enables the inaccessible authentication bypass feature, and configuration) configures the access VLAN for the feature.
Page 159: Dot1X Critical (Interface Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x critical (interface configuration) dot1x critical (interface configuration) Use the dot1x critical interface configuration command on the switch stack or on a standalone switch to enable the inaccessible-authentication-bypass feature, also referred to as critical authentication or the authentication, authorization, and accounting (AAA) fail policy.
Page 160 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x critical (interface configuration) You can configure the inaccessible authentication bypass feature and the restricted VLAN on an IEEE 802.1x port. If the switch tries to re-authenticate a critical port in a restricted VLAN and all the RADIUS servers are unavailable, the switch changes the port state to the critical authentication state, and it remains in the restricted VLAN.
Page 161: Dot1X Default
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x default dot1x default Use the dot1x default interface configuration command on the switch stack or on a standalone switch to reset the IEEE 802.1x parameters to their default values.
Page 162: Dot1X Fallback
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x fallback dot1x fallback Use the dot1xfallback interface configuration command on the switch stack or on a standalone switch to configure a port to use web authentication as a fallback method for clients that do not support IEEE 802.1x authentication.
Page 163: Dot1X Guest-Vlan
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x guest-vlan dot1x guest-vlan Use the dot1x guest-vlan interface configuration command on the switch stack or on a standalone switch to specify an active VLAN as an IEEE 802.1x guest VLAN. Use the no form of this command to return to the default setting.
Page 164 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x guest-vlan Any number of non-IEEE 802.1x-capable clients are allowed access when the switch port is moved to the guest VLAN. If an IEEE 802.1x-capable client joins the same port on which the guest VLAN is configured, the port is put into the unauthorized state in the RADIUS-configured or user-configured access VLAN, and authentication is restarted.
Page 165: Dot1X Host-Mode
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x host-mode dot1x host-mode Use the dot1x host-mode interface configuration command on the switch stack or on a standalone switch to allow a single host (client) or multiple hosts on an IEEE 802.1x-authorized port that has the dot1x port-control interface configuration command set to auto.
Page 166: Dot1X Initialize
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x initialize dot1x initialize Use the dot1x initialize privileged EXEC command on the switch stack or on a standalone switch to manually return the specified IEEE 802.1x-enabled port to an unauthorized state before initiating a new authentication session on the port.
Page 167: Dot1X Mac-Auth-Bypass
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x mac-auth-bypass dot1x mac-auth-bypass Use the dot1x mac-auth-bypass interface configuration command on the switch stack or on a standalone switch to enable the MAC authentication bypass feature. Use the no form of this command to disable MAC authentication bypass feature.
Page 168 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x mac-auth-bypass Examples This example shows how to enable MAC authentication bypass and to configure the switch to use EAP for authentication: Switch(config-if)# dot1x mac-auth-bypass eap You can verify your settings by entering the show dot1x [interface interface-id] privileged EXEC command.
Page 169: Dot1X Max-Reauth-Req
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x max-reauth-req dot1x max-reauth-req Use the dot1x max-reauth-req interface configuration command on the switch stack or on a standalone switch to set the maximum number of times that the switch restarts the authentication process before a port changes to the unauthorized state.
Page 170: Dot1X Max-Req
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x max-req dot1x max-req Use the dot1x max-req interface configuration command on the switch stack or on a standalone switch to set the maximum number of times that the switch sends an Extensible Authentication Protocol (EAP) frame from the authentication server (assuming that no response is received) to the client before restarting the authentication process.
Page 171: Dot1X Pae
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x pae dot1x pae Use the dot1x pae interface configuration command on the switch stack or on a standalone switch to configure the port as an IEEE 802.1x port access entity (PAE) authenticator. Use the no form of this command to disable IEEE 802.1x authentication on the port.
Page 172: Dot1X Port-Control
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x port-control dot1x port-control Use the dot1x port-control interface configuration command on the switch stack or on a standalone switch to enable manual control of the authorization state of the port. Use the no form of this command to return to the default setting.
Page 173 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x port-control Dynamic-access ports—If you try to enable IEEE 802.1x authentication on a dynamic-access • (VLAN Query Protocol [VQP]) port, an error message appears, and IEEE 802.1x authentication is not enabled.
Page 174: Dot1X Re-Authenticate
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x re-authenticate dot1x re-authenticate Use the dot1x re-authenticate privileged EXEC command on the switch stack or on a standalone switch to manually initiate a re-authentication of the specified IEEE 802.1x-enabled port.
Page 175: Dot1X Reauthentication
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x reauthentication dot1x reauthentication Use the dot1x reauthentication interface configuration command on the switch stack or on a standalone switch to enable periodic re-authentication of the client. Use the no form of this command to return to the default setting.
Page 176: Dot1X Timeout
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x timeout dot1x timeout Use the dot1x timeout interface configuration command on the switch stack or on a standalone switch to set IEEE 802.1x timers. Use the no form of this command to return to the default setting.
Page 177 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x timeout Usage Guidelines You should change the default value of this command only to adjust for unusual circumstances such as unreliable links or specific behavioral problems with certain clients and authentication servers.
Page 178: Dot1X Violation-Mode
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x violation-mode dot1x violation-mode Use the dot1x violation-mode interface configuration command on the switch stack or on a standalone switch to configure the violation modes that occur when a new device connects to a port or when a new device connects to a port after the maximum number of devices are connected to that port.
Page 179 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands dot1x violation-mode Related Commands Command Description show dot1x [interface interface-id] Displays IEEE 802.1x status for the specified port. Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference...
Page 180: Duplex
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands duplex duplex Use the duplex interface configuration command on the switch stack or on a standalone switch to specify the duplex mode of operation for a port. Use the no form of this command to return the port to its default value.
Page 181 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands duplex If the speed is set to auto, the switch negotiates with the device at the other end of the link for the speed setting and then forces the speed setting to the negotiated value. The duplex setting remains as configured on each end of the link, which could result in a duplex setting mismatch.
Page 182: Energywise (Global Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands energywise (global configuration) energywise (global configuration) Use the energywise global configuration command to enable and configure EnergyWise on an entity. Use the no form of this command to disable EnergyWise and to remove the EnergyWise configuration.
Page 183: Command Show Energywise
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands energywise (global configuration) The power level is 10. The udp-port-number is 43440. The name is the hostname. No neighbors are assigned. The role is the model number.
Page 184: Energywise (Interface Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands energywise (interface configuration) energywise (interface configuration) Use the energywise interface configuration command to configure EnergyWise on the power over Ethernet (PoE) port. Use the no form of this command to disable EnergyWise and to remove the EnergyWise configuration.
Page 185 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands energywise (interface configuration) name name (Optional) Specify the EnergyWise-specific port name. You can enter alphanumeric characters and symbols such as #, (, %, !, or •...
Page 186: Energywise Domain
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands energywise domain energywise domain Use the energywise domain global configuration command to enable EnergyWise on the entity, assign the entity to a domain, and set the password for secure communication among the domain entities. Use the no form of this command to disable EnergyWise and to remove the EnergyWise configuration.
Page 187 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands energywise domain Usage Guidelines If you enter the energywise domain domain-name secret [0 | 7] password command, the entity selects the first available port to communicate with the network and with management applications.
Page 188: Energywise Query
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands energywise query energywise query Use the energywise query privileged EXEC command to display power information or to power the entities or PoE ports in the domain.
Page 189 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands energywise query Defaults The importance value is 1. The power level is 10. Command Modes Privileged EXEC Command History Release Modification 12.2(50)SE This command was introduced.
Page 190 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands energywise query Switch# energywise query name lobby* collect usage EnergyWise query, timeout is 3 seconds: Host Name Usage ---- ---- ----- 2.2.4.30 lobbyInterface.17 10.0 (W) Queried:...
Page 191 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands energywise query Switch# energywise query name * set level 10 EnergyWise query, timeout is 3 seconds: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!! Success rate is (48/48) setting entities Queried: Responded: Time: 0.996 seconds...
Page 192: Errdisable Detect Cause
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands errdisable detect cause errdisable detect cause Use the errdisable detect cause global configuration command on the switch stack or on a standalone switch to enable error-disabled detection for a specific cause or all causes. Use the no form of this command to disable the error-disabled detection feature.
Page 193 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands errdisable detect cause Command Modes Global configuration Command History Release Modification 12.2(40)EX1 This command was introduced. Usage Guidelines A cause (link-flap, dhcp-rate-limit, and so forth) is the reason for the error-disabled state. When a cause is detected on an interface, the interface is placed in an error-disabled state, an operational state that is similar to a link-down state.
Page 194: Errdisable Detect Cause Small-Frame
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands errdisable detect cause small-frame errdisable detect cause small-frame Use the errdisable detect cause small-frame global configuration command on the switch stack or on a standalone switch to allow any switch port to be error disabled if incoming VLAN-tagged packets are small frames (67 bytes or less) and arrive at the minimum configured rate (the threshold).
Page 195 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands errdisable detect cause small-frame Related Commands Command Description errdisable detect cause Enables the recovery timer. small-frame errdisable recovery interval Specifies the time to recover from the specified error-disabled state.
Page 196: Errdisable Recovery
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands errdisable recovery errdisable recovery Use the errdisable recovery global configuration command on the switch stack or on a standalone switch to configure the recover mechanism variables. Use the no form of this command to return to the default setting.
Page 197 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands errdisable recovery vmps Enable the timer to recover from the VLAN Membership Policy Server (VMPS) error-disabled state. interval interval Specify the time to recover from the specified error-disabled state. The range is 30 to 86400 seconds.
Page 198 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands errdisable recovery Related Commands Command Description show errdisable recovery Displays error-disabled recovery timer information. show interfaces status Displays interface status or a list of interfaces in error-disabled err-disabled state.
Page 199: Errdisable Recovery Cause Small-Frame
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands errdisable recovery cause small-frame errdisable recovery cause small-frame Use the errdisable recovery cause small-frame global configuration command on the switch stack or on a standalone switch to enable the recovery timer for ports to be automatically re-enabled after they are error disabled by the arrival of small frames.
Page 200: Exception Crashinfo
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands exception crashinfo exception crashinfo Use the exception crashinfo global configuration command on the switch stack or on a standalone switch to configure the switch to create the extended crashinfo file when the Cisco IOS image fails. Use the no form of this command to disable this feature.
Page 201: Fallback Profile
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands fallback profile fallback profile Use the fallback profile global configuration command on the switch stack or on a standalone switch to create a fallback profile for web authentication. To return to the default setting, use the no form of this command.
Page 202 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands fallback profile Related Commands Command Description dot1x fallback Configure a port to use web authentication as a fallback method for clients that do not support IEEE 802.1x authentication.
Page 203: Flowcontrol
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands flowcontrol flowcontrol Use the flowcontrol interface configuration command on the switch stack or on a standalone switch to set the receive flow-control state for an interface. When flow control send is operable and on for a device and it detects any congestion at its end, it notifies the link partner or the remote device of the congestion by sending a pause frame.
Page 204 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands flowcontrol Table 2-5 shows the flow control results on local and remote ports for a combination of settings. The table assumes that receive desired has the same results as using the receive on keywords.
Page 205: Hw-Module
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands hw-module hw-module Use the hw-module global configuration command on the switch stack or on a standalone switch to enable on-board failure logging (OBFL). Use the no form of this command to disable this feature.
Page 206 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands hw-module This example shows how to enable OBFL on a standalone switch and to specify that only severity 1 hardware-related messages are stored in the flash memory of the switch:...
Page 207: Interface Port-Channel
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands interface port-channel interface port-channel Use the interface port-channel global configuration command on the switch stack or on a standalone switch to access or create the port-channel logical interface. Use the no form of this command to remove the port-channel.
Page 208 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands interface port-channel Follow these guidelines when you use the interface port-channel command: If you want to use the Cisco Discovery Protocol (CDP), you must configure it only on the physical •...
Page 209: Interface Range
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands interface range interface range Use the interface range global configuration command on the switch stack or on a standalone switch to enter interface range configuration mode and to execute a command on multiple ports at the same time.
Page 210 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands interface range For physical interfaces: stack member is the number used to identify the switch within the stack. The number ranges – from 1 to 9 and is assigned to the switch the first time the stack member initializes.
Page 211: Interface Vlan
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands interface vlan interface vlan Use the interface vlan global configuration command on the switch stack or on a standalone switch to create or access a dynamic switch virtual interface (SVI) and to enter interface configuration mode. Use the no form of this command to delete an SVI.
Page 212 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands interface vlan Examples This example shows how to create a new SVI with VLAN ID 23 and to enter interface configuration mode: Switch(config)# interface vlan 23...
Page 213: Ip Access-Group
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip access-group ip access-group Use the ip access-group interface configuration command on the switch stack or on a standalone switch to control access to a Layer 2 or Layer 3 interface. Use the no form of this command to remove all access groups or the specified access group from the interface.
Page 214 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip access-group You can use router ACLs, input port ACLs, and VLAN maps on the same switch. However, a port ACL takes precedence over a router ACL or VLAN map: •...
Page 215 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip access-group Related Commands Command Description access list Configures a numbered ACL. For syntax information, select Cisco IOS IP Command Reference, Volume 1 of 3:Addressing and Services, Release 12.2 >...
Page 216: Ip Address
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip address ip address Use the ip address interface configuration command on the switch stack or on a standalone switch to set an IP address for the Layer 2 switch or an IP address for each switch virtual interface (SVI) or routed port on the Layer 3 switch.
Page 217 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip address If your switch receives its IP address from a Bootstrap Protocol (BOOTP) or a DHCP server and you remove the switch IP address by using the no ip address command, IP processing is disabled, and the BOOTP or the DHCP server cannot reassign the address.
Page 218: Ip Admission
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip admission ip admission Use the ip admission interface configuration command to enable web authentication. You can also use this command in fallback-profile mode. Use the no form of this command to disable web authentication.
Page 219: Ip Admission Name Proxy Http
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip admission name proxy http ip admission name proxy http Use the ip admission name proxy http global configuration command to enable web authentication. Use the no form of this command to disable web authentication.
Page 220 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip admission name proxy http Related Commands Command Description dot1x fallback Configure a port to use web authentication as a fallback method for clients that do not support IEEE 802.1x authentication.
Page 221: Ip Arp Inspection Filter Vlan
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip arp inspection filter vlan ip arp inspection filter vlan Use the ip arp inspection filter vlan global configuration command on the switch stack or on a standalone switch to permit or deny Address Resolution Protocol (ARP) requests and responses from a host configured with a static IP address when dynamic ARP inspection is enabled.
Page 222 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip arp inspection filter vlan Examples This example shows how to apply the ARP ACL static-hosts to VLAN 1 for dynamic ARP inspection: Switch(config)# ip arp inspection filter static-hosts vlan 1 You can verify your settings by entering the show ip arp inspection vlan 1 privileged EXEC command.
Page 223: Ip Arp Inspection Limit
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip arp inspection limit ip arp inspection limit Use the ip arp inspection limit interface configuration command on the switch stack or on a standalone switch to limit the rate of incoming Address Resolution Protocol (ARP) requests and responses on an interface.
Page 224 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip arp inspection limit On stacking-capable switches, the rate limit is calculated separately on each switch in a switch stack. For a cross-stack EtherChannel, this means that the actual rate limit might be higher than the configured value.
Page 225: Ip Arp Inspection Log-Buffer
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip arp inspection log-buffer ip arp inspection log-buffer Use the ip arp inspection log-buffer global configuration command on the switch stack or on a standalone switch to configure the dynamic Address Resolution Protocol (ARP) inspection logging buffer.
Page 226 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip arp inspection log-buffer On stacking-capable switches, the log buffer configuration applies to each stack member in a switch stack. Each stack member has the specified logs number entries and generates system messages at the configured rate.
Page 227: Ip Arp Inspection Trust
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip arp inspection trust ip arp inspection trust Use the ip arp inspection trust interface configuration command on the switch stack or on a standalone switch to configure an interface trust state that determines which incoming Address Resolution Protocol (ARP) packets are inspected.
Page 228 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip arp inspection trust Related Commands Command Description ip arp inspection Configures the dynamic ARP inspection logging buffer. log-buffer show inventory Displays the trust state and the rate limit of ARP packets for the specified interfaces interface or all interfaces.
Page 229: Ip Arp Inspection Validate
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip arp inspection validate ip arp inspection validate Use the ip arp inspection validate global configuration command on the switch stack or on a standalone switch to perform specific checks for dynamic Address Resolution Protocol (ARP) inspection. Use the no form of this command to return to the default settings.
Page 230 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip arp inspection validate The allow-zeros keyword interacts with ARP access control lists (ACLs) in this way: If you configure an ARP ACL to deny ARP probes, they are dropped even if the allow-zero keyword •...
Page 231: Ip Arp Inspection Vlan
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip arp inspection vlan ip arp inspection vlan Use the ip arp inspection vlan global configuration command on the switch stack or on a standalone switch to enable dynamic Address Resolution Protocol (ARP) inspection on a per-VLAN basis. Use the no form of this command to return to the default setting.
Page 232: Ip Arp Inspection Vlan Logging
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip arp inspection vlan logging ip arp inspection vlan logging Use the ip arp inspection vlan logging global configuration command on the switch stack or on a standalone switch to control the type of packets that are logged per VLAN.
Page 233 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip arp inspection vlan logging Usage Guidelines The term logged means that the entry is placed into the log buffer and that a system message is generated.
Page 234: Ip Dhcp Snooping
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip dhcp snooping ip dhcp snooping Use the ip dhcp snooping global configuration command on the switch stack or on a standalone switch to globally enable DHCP snooping. Use the no form of this command to return to the default setting.
Page 235: Ip Dhcp Snooping Binding
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip dhcp snooping binding ip dhcp snooping binding Use the ip dhcp snooping binding privileged EXEC command on the switch stack or on a standalone switch to configure the DHCP snooping binding database and to add binding entries to the database. Use the no form of this command to delete entries from the binding database.
Page 236 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip dhcp snooping binding Related Commands Command Description ip dhcp snooping Enables DHCP snooping on a VLAN. show ip dhcp snooping binding Displays the dynamically configured bindings in the DHCP snooping binding database and the configuration information.
Page 237: Ip Dhcp Snooping Database
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip dhcp snooping database ip dhcp snooping database Use the ip dhcp snooping database global configuration command on the switch stack or on a standalone switch to configure the DHCP snooping binding database agent. Use the no form of this command to disable the agent, to reset the timeout value, or to reset the write-delay value.
Page 238 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip dhcp snooping database Command History Release Modification 12.2(40)EX1 This command was introduced. Usage Guidelines The DHCP snooping binding database can have up to 8192 bindings.
Page 239: Ip Dhcp Snooping Information Option
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip dhcp snooping information option ip dhcp snooping information option Use the ip dhcp snooping information option global configuration command on the switch stack or on a standalone switch to enable DHCP option-82 data insertion.
Page 240 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip dhcp snooping information option Related Commands Command Description show ip dhcp snooping Displays the DHCP snooping configuration. show ip dhcp snooping binding Displays the DHCP snooping binding information.
Page 241: Ip Dhcp Snooping Information Option Allow-Untrusted
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip dhcp snooping information option allow-untrusted ip dhcp snooping information option allow-untrusted Use the ip dhcp snooping information option allow-untrusted global configuration command on an aggregation switch to configure it to accept DHCP packets with option-82 information that are received on untrusted ports that might be connected to an edge switch.
Page 242 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip dhcp snooping information option allow-untrusted You can verify your settings by entering the show ip dhcp snooping user EXEC command. Related Commands Command Description show ip dhcp snooping Displays the DHCP snooping configuration.
Page 243: Ip Dhcp Snooping Information Option Format Remote-Id
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip dhcp snooping information option format remote-id ip dhcp snooping information option format remote-id Use the ip dhcp snooping information option format remote-id global configuration command on the switch stack or on a standalone switch to configure the option-82 remote-ID suboption.
Page 244: Ip Dhcp Snooping Limit Rate
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip dhcp snooping limit rate ip dhcp snooping limit rate Use the ip dhcp snooping limit rate interface configuration command on the switch stack or on a standalone switch to configure the number of DHCP messages an interface can receive per second.
Page 245: Ip Dhcp Snooping Trust
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip dhcp snooping trust ip dhcp snooping trust Use the ip dhcp snooping trust interface configuration command on the switch stack or on a standalone switch to configure a port as trusted for DHCP snooping purposes. Use the no form of this command to return to the default setting.
Page 246: Ip Dhcp Snooping Verify
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip dhcp snooping verify ip dhcp snooping verify Use the ip dhcp snooping verify global configuration command on the switch stack or on a standalone switch to configure the switch to verify on an untrusted port that the source MAC address in a DHCP packet matches the client hardware address.
Page 247: Ip Dhcp Snooping Vlan
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip dhcp snooping vlan ip dhcp snooping vlan Use the ip dhcp snooping vlan global configuration command on the switch stack or on a standalone switch to enable DHCP snooping on a VLAN. Use the no form of this command to return to the default setting.
Page 248: Ip Dhcp Snooping Vlan Information Option Format-Type Circuit-Id String
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip dhcp snooping vlan information option format-type circuit-id string ip dhcp snooping vlan information option format-type circuit-id string Use the ip dhcp snooping vlan information option format-type circuit-id string interface configuration command on the switch stack or on a standalone switch to configure the option-82 circuit-ID suboption.
Page 249 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip dhcp snooping vlan information option format-type circuit-id string The show ip dhcp snooping user EXEC command only displays the global command output, including Note a remote-ID configuration. It does not display any per-interface, per-VLAN string that you have configured for the circuit ID.
Page 250: Ip Igmp Filter
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip igmp filter ip igmp filter Use the ip igmp filter interface configuration command on the switch stack or on a standalone switch to control whether or not all hosts on a Layer 2 interface can join one or more IP multicast groups by applying an Internet Group Management Protocol (IGMP) profile to the interface.
Page 251 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip igmp filter Related Commands Command Description ip igmp profile Configures the specified IGMP profile number. show ip dhcp snooping Displays the characteristics of the specified IGMP profile.
Page 252: Ip Igmp Max-Groups
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip igmp max-groups ip igmp max-groups Use the ip igmp max-groups interface configuration command on the switch stack or on a standalone switch to set the maximum number of Internet Group Management Protocol (IGMP) groups that a Layer 2 interface can join or to configure the IGMP throttling action when the maximum number of entries is in the forwarding table.
Page 253 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip igmp max-groups Follow these guidelines when configuring the IGMP throttling action: If you configure the throttling action as deny and set the maximum group limitation, the entries that •...
Page 254: Ip Igmp Profile
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip igmp profile ip igmp profile Use the ip igmp profile global configuration command on the switch stack or on a standalone switch to create an Internet Group Management Protocol (IGMP) profile and enter IGMP profile configuration mode.
Page 255 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip igmp profile Related Commands Command Description ip igmp filter Applies the IGMP profile to the specified interface. show ip dhcp snooping Displays the characteristics of all IGMP profiles or the specified statistics IGMP profile number.
Page 256: Ip Igmp Snooping
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip igmp snooping ip igmp snooping Use the ip igmp snooping global configuration command on the switch stack or on a standalone switch to globally enable Internet Group Management Protocol (IGMP) snooping on the switch or to enable it on a per-VLAN basis.
Page 257 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip igmp snooping Related Commands Command Description ip igmp snooping report-suppression Enables IGMP report suppression. show ip igmp snooping Displays the snooping configuration. show ip igmp snooping groups Displays IGMP snooping multicast information.
Page 258: Ip Igmp Snooping Last-Member-Query-Interval
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip igmp snooping last-member-query-interval ip igmp snooping last-member-query-interval Use the ip igmp snooping last-member-query-interval global configuration command on the switch stack or on a standalone switch to enable the Internet Group Management Protocol (IGMP) configurable-leave timer globally or on a per-VLAN basis.
Page 259 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip igmp snooping last-member-query-interval Related Commands Command Description ip igmp snooping Enables IGMP snooping on the switch or on a VLAN. ip igmp snooping vlan immediate-leave Enables IGMP Immediate-Leave processing.
Page 260: Ip Igmp Snooping Querier
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip igmp snooping querier ip igmp snooping querier Use the ip igmp snooping querier global configuration command on the switch stack or on a standalone switch to globally enable the Internet Group Management Protocol (IGMP) querier function in Layer 2 networks.
Page 261 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip igmp snooping querier Usage Guidelines Use this command to enable IGMP snooping to detect the IGMP version and IP address of a device that sends IGMP query messages, which is also called a querier.
Page 262: Ip Igmp Snooping Report-Suppression
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip igmp snooping report-suppression ip igmp snooping report-suppression Use the ip igmp snooping report-suppression global configuration command on the switch stack or on a standalone switch to enable Internet Group Management Protocol (IGMP) report suppression. Use the no form of this command to disable IGMP report suppression and to forward all IGMP reports to multicast routers.
Page 263 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip igmp snooping report-suppression Related Commands Command Description ip igmp snooping Enables IGMP snooping on the switch or on a VLAN. show ip igmp snooping Displays the IGMP snooping configuration of the switch or the VLAN.
Page 264: Ip Igmp Snooping Tcn
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip igmp snooping tcn ip igmp snooping tcn Use the ip igmp snooping tcn global configuration command on the switch stack or on a standalone switch to configure the Internet Group Management Protocol (IGMP) Topology Change Notification (TCN) behavior.
Page 265 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip igmp snooping tcn Related Commands Command Description ip igmp snooping Enables IGMP snooping on the switch or on a VLAN. ip igmp snooping tcn flood Specifies flooding on an interface as the IGMP snooping spanning-tree TCN behavior.
Page 266: Ip Igmp Snooping Tcn Flood
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip igmp snooping tcn flood ip igmp snooping tcn flood Use the ip igmp snooping tcn flood interface configuration command on the switch stack or on a standalone switch to specify multicast flooding as the Internet Group Management Protocol (IGMP) snooping spanning-tree Topology Change Notification (TCN) behavior.
Page 267: Ip Igmp Snooping Vlan Immediate-Leave
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip igmp snooping vlan immediate-leave ip igmp snooping vlan immediate-leave Use the ip igmp snooping immediate-leave global configuration command on the switch stack or on a standalone switch to enable Internet Group Management Protocol (IGMP) snooping immediate-leave processing on a per-VLAN basis.
Page 268: Ip Igmp Snooping Vlan Mrouter
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip igmp snooping vlan mrouter ip igmp snooping vlan mrouter Use the ip igmp snooping mrouter global configuration command on the switch stack or on a standalone switch to add a multicast router port or to configure the multicast learning method.
Page 269 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip igmp snooping vlan mrouter Examples This example shows how to configure a port as a multicast router port: Switch(config)# ip igmp snooping vlan 1 mrouter interface gigabitethernet1/0/2...
Page 270: Ip Igmp Snooping Vlan Static
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip igmp snooping vlan static ip igmp snooping vlan static Use the ip igmp snooping static global configuration command on the switch stack or on a standalone switch to enable Internet Group Management Protocol (IGMP) snooping and to statically add a Layer 2 port as a member of a multicast group.
Page 271 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip igmp snooping vlan static Related Commands Command Description ip igmp snooping report-suppression Enables IGMP report suppression. show ip igmp snooping Displays the snooping configuration. show ip igmp snooping groups Displays IGMP snooping multicast information.
Page 272: Ip Snap Forwarding
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip snap forwarding ip snap forwarding Use the ip snap forwarding global configuration command on the switch stack or on a standalone switch to enable forwarding of IP Version 4 (IPv4) and IP Version 6 (IPv6) frames with Subnetwork Access Protocol (SNAP) encapsulation.
Page 273: Ip Source Binding
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip source binding ip source binding Use the ip source binding global configuration command on the switch stack or on a standalone switch to configure static IP source bindings on the switch. Use the no form of this command to delete static bindings.
Page 274 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip source binding Related Commands Command Description ip verify source Enables IP source guard on an interface. show ip source binding Displays the IP source bindings on the switch.
Page 275: Ip Ssh
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip ssh ip ssh Use the ip ssh global configuration command on the switch stack or on a standalone switch to configure the switch to run Secure Shell (SSH) Version 1 or SSH Version 2. This command is available only when your switch is running the cryptographic (encrypted) software image.
Page 276 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip ssh Related Commands Command Description show ip ssh Displays if the SSH server is enabled and displays the version and configuration information for the SSH server. For syntax information, select Cisco IOS Release 12.2 Configuration Guides and Command References >...
Page 277: Ip Sticky-Arp (Global Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip sticky-arp (global configuration) ip sticky-arp (global configuration) Use the ip sticky-arp global configuration command to enable sticky Address Resolution Protocol (ARP) on a switch virtual interface (SVI) that belongs to a private VLAN. Use the no form of this command to disable sticky ARP.
Page 278 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip sticky-arp (global configuration) Use the no sticky-arp global configuration command to disable sticky ARP on the switch. • Use the no sticky-arp interface configuration command to disable sticky ARP on an interface when •...
Page 279: Ip Sticky-Arp (Interface Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip sticky-arp (interface configuration) ip sticky-arp (interface configuration) Use the ip sticky-arp interface configuration command to enable sticky Address Resolution Protocol (ARP) on a switch virtual interface (SVI) or a Layer 3 interface. Use the no form of this command to disable sticky ARP.
Page 280 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip sticky-arp (interface configuration) If you disconnect the switch from a device and then connect it to another device with a different • MAC address but with the same IP address, the ARP entry is not created, and this message appears: *Mar 2 00:26:06.967: %IP-3-STCKYARPOVR: Attempt to overwrite Sticky ARP entry:...
Page 281: Ip Verify Source
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ip verify source ip verify source Use the ip verify source interface configuration command on the switch stack or on a standalone switch to enable IP source guard on an interface. Use the no form of this command to disable IP source guard.
Page 282: Ipv6 Access-List
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 access-list ipv6 access-list Use the ipv6 access-list global configuration command on the switch stack or on a standalone switch to define an IPv6 access list and to place the switch in IPv6 access list configuration mode. To remove the access list, use the no form of this command.
Page 283 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 access-list The IPv6 neighbor discovery process makes use of the IPv6 network layer service; therefore, by default, IPv6 ACLs implicitly allow IPv6 neighbor discovery packets to be sent and received on an interface. In IPv4, the Address Resolution Protocol (ARP), which is equivalent to the IPv6 neighbor discovery process, uses a separate data-link layer protocol;...
Page 284: Ipv6 Address Dhcp
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 address dhcp ipv6 address dhcp Use the ipv6 address dhcp interface configuration command on the switch stack or on a standalone switch to acquire an IPv6 address on an interface from the Dynamic Host Configuration Protocol for IPv6 (DHCPv6) server.
Page 285: Ipv6 Dhcp Client Request Vendor
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 dhcp client request vendor ipv6 dhcp client request vendor Use the ipv6 dhcp client request interface configuration command on the switch stack or on a standalone switch to configure an IPv6 client to request an option from a Dynamic Host Configuration Protocol for IPv6 (DHCPv6) server.
Page 286: Ipv6 Dhcp Ping Packets
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 dhcp ping packets ipv6 dhcp ping packets Use the ipv6 dhcp ping packets global configuration command on the switch stack or on a standalone switch to specify the number of packets a Dynamic Host Configuration Protocol for IPv6 (DHCPv6) server sends to a pool address as part of a ping operation.
Page 287 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 dhcp ping packets Related Commands Command Description clear ipv6 dhcp Clears an address conflict from the DHCPv6 server database. conflict show ipv6 dhcp Displays address conflicts found by a DHCPv6 server, or reported through conflict a DECLINE message from a client.
Page 288: Ipv6 Dhcp Pool
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 dhcp pool ipv6 dhcp pool Use the ipv6 dhcp pool global configuration command on the switch stack or on a standalone switch to enter Dynamic Host Configuration Protocol for IPv6 (DHCPv6) pool configuration mode. Use the no form of this command to return to the default settings.
Page 289 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 dhcp pool vendor-specific: enables the DHCPv6 vendor-specific configuration mode. These configuration • commands are available: – vendor-id: enter a vendor-specific identification number. This number is the vendor IANA Private Enterprise Number.
Page 290: Ipv6 Dhcp Server
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 dhcp server ipv6 dhcp server Use the ipv6 dhcp server interface configuration command on the switch stack or on a standalone switch to enable Dynamic Host Configuration Protocol for IPv6 (DHCPv6) service on an interface. To disable DHCPv6 service on an interface, use the no form of this command.
Page 291 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 dhcp server If the packet was directly received from the client, the server performs this same matching, but it uses all the IPv6 addresses configured on the incoming interface when performing the match. Once again, the server selects the longest prefix match.
Page 292: Ipv6 Mld Snooping
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 mld snooping ipv6 mld snooping Use the ipv6 mld snooping global configuration command on the switch stack or on a standalone switch without keywords to enable IP version 6 (IPv6) Multicast Listener Discovery (MLD) snooping globally or on the specified VLAN.
Page 293 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 mld snooping Examples This example shows how to globally enable MLD snooping: Switch(config)# ipv6 mld snooping This example shows how to disable MLD snooping on a VLAN: Switch(config)# no ipv6 mld snooping vlan 11 You can verify your settings by entering the show ipv6 mld snooping user EXEC command.
Page 294: Ipv6 Mld Snooping Last-Listener-Query-Count
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 mld snooping last-listener-query-count ipv6 mld snooping last-listener-query-count Use the ipv6 mld snooping last-listener-query-count global configuration command on the switch stack or on a standalone switch to configure IP version 6 (IPv6) Multicast Listener Discovery Mulitcast Address Specific Queries (MASQs) or that will be sent before aging out a client.
Page 295 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 mld snooping last-listener-query-count Examples This example shows how to globally set the last-listener query count: Switch(config)# ipv6 mld snooping last-listener-query-count 1 This example shows how to set the last-listener query count for VLAN 10:...
Page 296: Ipv6 Mld Snooping Last-Listener-Query-Interval
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 mld snooping last-listener-query-interval ipv6 mld snooping last-listener-query-interval Use the ipv6 mld snooping last-listener-query-interval global configuration command on the switch stack or on a standalone switch to configure IP version 6 (IPv6) Multicast Listener Discovery (MLD) snooping last-listener query interval on the switch or on a VLAN.
Page 297 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 mld snooping last-listener-query-interval Examples This example shows how to globally set the last-listener query interval to 2 seconds: Switch(config)# ipv6 mld snooping last-listener-query-interval 2000 This example shows how to set the last-listener query interval for VLAN 1 to 5.5 seconds:...
Page 298: Ipv6 Mld Snooping Listener-Message-Suppression
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 mld snooping listener-message-suppression ipv6 mld snooping listener-message-suppression Use the ipv6 mld snooping listener-message-suppression global configuration command on the switch stack or on a standalone switch to enable IP version 6 (IPv6) Multicast Listener Discovery (MLD) snooping listener message suppression.
Page 299 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 mld snooping listener-message-suppression Related Commands Command Description ipv6 mld snooping Enables IPv6 MLD snooping. sdm prefer Configures an SDM template to optimize system resources based on how the switch is being used.
Page 300: Ipv6 Mld Snooping Robustness-Variable
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 mld snooping robustness-variable ipv6 mld snooping robustness-variable Use the ipv6 mld snooping robustness-variable global configuration command on the switch stack or on a standalone switch to configure the number of IP version 6 (IPv6) Multicast Listener Discovery (MLD) queries that the switch sends before deleting a listener that does not respond, or enter a VLAN ID to configure on a per-VLAN basis.
Page 301 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 mld snooping robustness-variable Examples This example shows how to configure the global robustness variable so that the switch sends out three queries before it deletes a listener port that does not respond: Switch(config)# ipv6 mld snooping robustness-variable 3 This example shows how to configure the robustness variable for VLAN 1.
Page 302: Ipv6 Mld Snooping Tcn
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 mld snooping tcn ipv6 mld snooping tcn Use the ipv6 mld snooping tcn global configuration commands on the switch stack or on a standalone switch to configure IP version 6 (IPv6) Multicast Listener Discovery (MLD) Topology Change Notifications (TCNs).
Page 303 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 mld snooping tcn Related Commands Command Description sdm prefer Configures an SDM template to optimize system resources based on how the switch is being used.
Page 304: Ipv6 Mld Snooping Vlan
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 mld snooping vlan ipv6 mld snooping vlan Use the ipv6 mld snooping vlan global configuration command on the switch stack or on a standalone switch to configure IP version 6 (IPv6) Multicast Listener Discovery (MLD) snooping parameters on the VLAN interface.
Page 305 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 mld snooping vlan The configuration and the static ports and groups are saved in NVRAM. When the IPv6 multicast router is a Catalyst 6500 switch and you are using extended VLANs (in the range 1006 to 4094), IPv6 MLD snooping must be enabled on the extended VLAN on the Catalyst 6500 switch in order for the switch to receive queries on the VLAN.
Page 306: Ipv6 Traffic-Filter
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 traffic-filter ipv6 traffic-filter Use the ipv6 traffic-filter interface configuration command on the switch stack or on a standalone switch to filter IPv6 traffic on an interface. The type and direction of traffic that you can filter depends on the feature set running on the switch stack.
Page 307 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands ipv6 traffic-filter Examples This example filters inbound IPv6 traffic on an IPv6-configured interface as defined by the access list named cisco: Switch (config)# interface gigabitethernet1/0/1 Switch(config-if)# no switchport...
Page 308: L2Protocol-Tunnel
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands l2protocol-tunnel l2protocol-tunnel Use the l2protocol-tunnel interface configuration command on the switch stack or on a standalone switch to enable tunneling of Layer 2 protocols on an access port, IEEE 802.1Q tunnel port, or a port channel.
Page 309 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands l2protocol-tunnel Command Modes Interface configuration Command History Release Modification 12.2(40)EX1 This command was introduced. Usage Guidelines You must enter this command, with or without protocol types, to tunnel Layer 2 packets.
Page 310 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands l2protocol-tunnel The configuration is saved in NVRAM. For more information about Layer 2 protocol tunneling, see the software configuration guide for this release. Examples This example shows how to enable protocol tunneling for CDP packets and to configure the shutdown...
Page 311: L2Protocol-Tunnel Cos
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands l2protocol-tunnel cos l2protocol-tunnel cos Use the l2protocol-tunnel cos global configuration command on the switch stack or on a standalone switch to configure class of service (CoS) value for all tunneled Layer 2 protocol packets. Use the no form of this command to return to the default setting.
Page 312: Lacp Port-Priority
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands lacp port-priority lacp port-priority Use the lacp port-priority interface configuration command on the switch stack or on a standalone switch to configure the port priority for the Link Aggregation Control Protocol (LACP). Use the no form of this command to return to the default setting.
Page 313 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands lacp port-priority Examples This example shows how to configure the LACP port priority on a port: Switch(config)# interface gigabitethernet2/0/1 Switch(config-if)# lacp port-priority 1000 You can verify your settings by entering the show lacp [channel-group-number] internal privileged EXEC command.
Page 314: Lacp System-Priority
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands lacp system-priority lacp system-priority Use the lacp system-priority global configuration command on the switch stack or on a standalone switch to configure the system priority for the Link Aggregation Control Protocol (LACP). Use the no form of this command to return to the default setting.
Page 315 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands lacp system-priority Related Commands Command Description channel-group Assigns an Ethernet port to an EtherChannel group. lacp port-priority Configures the LACP port priority. show lacp sys-id Displays the system identifier that is being used by LACP.
Page 316: Link State Group
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands link state group link state group Use the link state group interface configuration command to configure a port as a member of a link-state group. Use the no form of this command to remove the port from the link-state group.
Page 317 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands link state group Examples This example shows how to configure the interfaces as upstream in group 1: Switch# configure terminal Switch(config)# interface port-channel 1 Switch(config-if)# link state group 1 upstream Switch(config-if)# end You can verify your settings by entering the show running-config privileged EXEC command.
Page 318: Link State Track
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands link state track link state track Use the link state track user EXEC command to enable a link-state group. Use the no form of this command to disable a link-state group.
Page 319: Location (Global Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands location (global configuration) location (global configuration) Use the location global configuration command to configure location information for an endpoint. Use the no form of this command to remove the location information.
Page 320 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands location (global configuration) This example shows how to configure the emergency location information location on the switch: Switch (config)# location elin-location 14085553881 identifier 1 You can verify your settings by entering the show location elin privileged EXEC command.
Page 321: Location (Interface Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands location (interface configuration) location (interface configuration) Use the location interface command to enter location information for an interface. Use the no form of this command to remove the interface location information.
Page 322 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands location (interface configuration) Related Commands Command Description location (global configuration) Configures the location information for an endpoint. show location Displays the location information for an endpoint.
Page 323: Logging File
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands logging file logging file Use the logging file global configuration command on the switch stack or on a standalone switch to set logging file parameters. Use the no form of this command to return to the default setting.
Page 324 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands logging file Command History Release Modification 12.2(40)EX1 This command was introduced. Usage Guidelines On a stacking-capable switch, the log file is stored in ASCII text format in an internal buffer on a standalone switch, and in the case of a switch stack, on the stack master.
Page 325: Mac Access-Group
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mac access-group mac access-group Use the mac access-group interface configuration command on the switch stack or on a standalone switch to apply a MAC access control list (ACL) to a Layer 2 interface. Use the no form of this command to remove all MAC ACLs or the specified MAC ACL from the interface.
Page 326 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mac access-group Examples This example shows how to apply a MAC extended ACL named macacl2 to an interface: Switch(config)# interface gigabitethernet1/0/1 Switch(config-if)# mac access-group macacl2 in You can verify your settings by entering the show mac access-group privileged EXEC command.
Page 327: Mac Access-List Extended
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mac access-list extended mac access-list extended Use the mac access-list extended global configuration command on the switch stack or on a standalone switch to create an access list based on MAC addresses for non-IP traffic. Using this command puts you in the extended MAC access-list configuration mode.
Page 328 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mac access-list extended Examples This example shows how to create a MAC named extended access list named mac1 and to enter extended MAC access-list configuration mode:...
Page 329: Mac Address-Table Aging-Time
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mac address-table aging-time mac address-table aging-time Use the mac address-table aging-time global configuration command on the switch stack or on a standalone switch to set the length of time that a dynamic entry remains in the MAC address table after the entry is used or updated.
Page 330: Mac Address-Table Learning Vlan
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mac address-table learning vlan mac address-table learning vlan Use the mac address-table learning global configuration command to enable MAC address learning on a VLAN. This is the default state. Use the no form of this command to disable MAC address learning on a VLAN to control which VLANs can learn MAC addresses.
Page 331 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mac address-table learning vlan If you disable MAC address learning on a VLAN that includes a secure port, MAC address learning is not disabled on the secure port. If you later disable port security on the interface, the disabled MAC address learning state is enabled.
Page 332: Mac Address-Table Move Update
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mac address-table move update mac address-table move update Use the mac address-table move update global configuration command on the switch stack or on a standalone switch to enable the MAC address-table move update feature. Use the no form of this command to return to the default setting.
Page 333 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mac address-table move update Related Commands Command Description clear mac address-table move Clears the MAC address-table move update global counters. update debug matm move update Debugs the MAC address-table move update message processing.
Page 334: Mac Address-Table Notification
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mac address-table notification mac address-table notification Use the mac address-table notification global configuration command on the switch stack or on a standalone switch to enable the MAC address notification feature on the switch or the switch stack. Use the no form of this command to return to the default setting.
Page 335 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mac address-table notification Examples This example shows how to enable the MAC address-table notification feature, set the interval time to 60 seconds, and set the history-size to 100 entries:...
Page 336: Mac Address-Table Static
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mac address-table static mac address-table static Use the mac address-table static global configuration command on the switch stack or on a standalone switch to add static addresses to the MAC address table. Use the no form of this command to remove static entries from the table.
Page 337: Mac Address-Table Static Drop
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mac address-table static drop mac address-table static drop Use the mac address-table static drop global configuration command on the switch stack or on a standalone switch to enable unicast MAC address filtering and to configure the switch to drop traffic with a specific source or destination MAC address.
Page 338 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mac address-table static drop Examples This example shows how to enable unicast MAC address filtering and to configure the switch to drop packets that have a source or destination address of c2f3.220a.12f4. When a packet is received in VLAN 4 with this MAC address as its source or destination, the packet is dropped: Switch(config)# mac address-table static c2f3.220a.12f4 vlan 4 drop...
Page 339: Macro Apply
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands macro apply macro apply Use the macro apply interface configuration command on the switch stack or on a standalone switch to apply a macro to an interface or to apply and trace a macro configuration on an interface.
Page 340 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands macro apply Follow these guidelines when you apply a Cisco-default Smartports macro on an interface: Display all macros on the switch by using the show parser macro user EXEC command. Display •...
Page 341 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands macro apply # Configure port as an edge network port spanning-tree portfast spanning-tree bpduguard enable -------------------------------------------------------------- Switch# Switch# configure terminal Switch(config)# interface gigabitethernet1/0/4 Switch(config-if)# macro apply cisco-desktop $AVID 25...
Page 342: Macro Description
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands macro description macro description Use the macro description interface configuration command on the switch stack or on a standalone switch to enter a description about which macros are applied to an interface. Use the no form of this command to remove the description.
Page 343: Macro Global
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands macro global macro global Use the macro global global configuration command on the switch stack or on a standalone switch to apply a macro to a switch or to apply and trace a macro configuration on a switch.
Page 344 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands macro global Follow these guidelines when you apply a Cisco-default Smartports macro on a switch: Display all macros on the switch by using the show parser macro user EXEC command. Display •...
Page 345 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands macro global Related Commands Command Description macro apply Applies a macro on an interface or applies and traces a macro on an interface. macro description Adds a description about the macros that are applied to an interface.
Page 346: Macro Global Description
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands macro global description macro global description Use the macro global description global configuration command on the switch stack or on a standalone switch to enter a description about the macros that are applied to the switch. Use the no form of this command to remove the description.
Page 347: Macro Name
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands macro name macro name Use the macro name global configuration command on the switch stack or on a standalone switch to create a configuration macro. Use the no form of this command to delete the macro definition.
Page 348 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands macro name Examples This example shows how to create a macro that defines the duplex mode and speed: Switch(config)# macro name duplex Enter macro commands one per line. End with the character ‘@’.
Page 349: Match (Access-Map Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands match (access-map configuration) match (access-map configuration) Use the match access-map configuration command on the switch stack or on a standalone switch to set the VLAN map to match packets against one or more access lists. Use the no form of this command to remove the match parameters.
Page 350 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands match (access-map configuration) Examples This example shows how to define and apply a VLAN access map vmap4 to VLANs 5 and 6 that will cause the interface to drop an IP packet if the packet matches the conditions defined in access list al2.
Page 351: Match (Class-Map Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands match (class-map configuration) match (class-map configuration) Use the match class-map configuration command on the switch stack or on a standalone switch to define the match criteria to classify traffic. Use the no form of this command to remove the match criteria.
Page 352 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands match (class-map configuration) If you enter the class-map {match-all | match-any} class-map-name global configuration command, you can enter these match commands: • match access-group acl-name The ACL must be an extended named ACL.
Page 353 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands match (class-map configuration) This example shows how to specify a range of physical ports to which an interface-level class map in a hierarchical policy map applies:...
Page 354: Mdix Auto
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mdix auto mdix auto Use the mdix auto interface configuration command on the switch stack or on a standalone switch to enable the automatic medium-dependent interface crossover (auto-MDIX) feature on the interface.
Page 355 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mdix auto Related Commands Command Description Displays general information about internal registers of an interface, show controllers including the operational state of auto-MDIX. ethernet-controller interface-id phy...
Page 356: Mls Qos
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos mls qos Use the mls qos global configuration command on the switch stack or on a standalone switch to enable quality of service (QoS) for the entire switch. When the mls qos command is entered, QoS is enabled with the default parameters on all ports in the system.
Page 357 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos Related Commands Command Description show mls qos Displays QoS information. Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference 2-327 OL-13271-03...
Page 358: Mls Qos Aggregate-Policer
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos aggregate-policer mls qos aggregate-policer Use the mls qos aggregate-policer global configuration command on the switch stack or on a standalone switch to define policer parameters, which can be shared by multiple classes within the same policy map.
Page 359 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos aggregate-policer Policing uses a token-bucket algorithm. You configure the bucket depth (the maximum burst that is tolerated before the bucket overflows) by using the burst-byte option of the police policy-map class configuration command or the mls qos aggregate-policer global configuration command.
Page 360: Mls Qos Cos
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos cos mls qos cos Use the mls qos cos interface configuration command on the switch stack or on a standalone switch to define the default class of service (CoS) value of a port or to assign the default CoS to all incoming packets on the port.
Page 361 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos cos This example shows how to assign all the packets entering a port to the default port CoS value of 4 on a port:...
Page 362: Mls Qos Dscp-Mutation
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos dscp-mutation mls qos dscp-mutation Use the mls qos dscp-mutation interface configuration command on the switch stack or on a standalone switch to apply a Differentiated Services Code Point (DSCP)-to-DSCP-mutation map to a DSCP-trusted port.
Page 363 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos dscp-mutation This example show how to remove the DSCP-to-DSCP-mutation map name dscpmutation1 from the port and to reset the map to the default: Switch(config-if)# no mls qos dscp-mutation dscpmutation1 You can verify your settings by entering the show mls qos maps privileged EXEC command.
Page 364: Mls Qos Map
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos map mls qos map Use the mls qos map global configuration command on the switch stack or on a standalone switch to define the class of service (CoS)-to-Differentiated Services Code Point (DSCP) map, DSCP-to-CoS map, the DSCP-to-DSCP-mutation map, the IP-precedence-to-DSCP map, and the policed-DSCP map.
Page 365 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos map Defaults Table 2-6 shows the default CoS-to-DSCP map: Table 2-6 Default CoS-to-DSCP Map CoS Value DSCP Value Table 2-7 shows the default DSCP-to-CoS map:...
Page 366 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos map The default DSCP-to-DSCP-mutation map is a null map, which maps an incoming DSCP value to the same DSCP value. The default policed-DSCP map is a null map, which maps an incoming DSCP value to the same DSCP value.
Page 367 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos map Related Commands Command Description mls qos dscp-mutation Applies a DSCP-to-DSCP-mutation map to a DSCP-trusted port. show mls qos maps Displays quality of service (QoS) mapping information.
Page 368: Mls Qos Queue-Set Output Buffers
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos queue-set output buffers mls qos queue-set output buffers Use the mls qos queue-set output buffers global configuration command on the switch stack or on a standalone switch to allocate buffers to a queue-set (four egress queues per port).
Page 369 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos queue-set output buffers You can verify your settings by entering the show mls qos interface [interface-id] buffers or the show mls qos queue-set privileged EXEC command.
Page 370: Mls Qos Queue-Set Output Threshold
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos queue-set output threshold mls qos queue-set output threshold Use the mls qos queue-set output threshold global configuration command on the switch stack or on...
Page 371 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos queue-set output threshold Usage Guidelines Use the mls qos queue-set output qset-id buffers global configuration command to allocate a fixed number of buffers to the four queues in a queue-set.
Page 372: Mls Qos Rewrite Ip Dscp
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos rewrite ip dscp mls qos rewrite ip dscp Use the mls qos rewrite ip dscp global configuration command on the switch stack or on a standalone switch to configure the switch to change (rewrite) the Differentiated Services Code Point (DSCP) field of an incoming IP packet.
Page 373 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos rewrite ip dscp Examples This example shows how to enable DSCP transparency and configure the switch to not change the DSCP value of the incoming IP packet:...
Page 374: Mls Qos Srr-Queue Input Bandwidth
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos srr-queue input bandwidth mls qos srr-queue input bandwidth Use the mls qos srr-queue input bandwidth global configuration command on the switch stack or on a standalone switch to assign shaped round robin (SRR) weights to an ingress queue.
Page 375 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos srr-queue input bandwidth This example shows how to assign the ingress bandwidths for the queues in the stack. Queue 1 is the priority queue with 10 percent of the bandwidth allocated to it. The bandwidth ratio allocated to queues 1 and 2 is 4/(4+4).
Page 376: Mls Qos Srr-Queue Input Buffers
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos srr-queue input buffers mls qos srr-queue input buffers Use the mls qos srr-queue input buffers global configuration command on the switch stack or on a standalone switch to allocate the buffers between the ingress queues.
Page 377 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos srr-queue input buffers Related Commands Command Description mls qos srr-queue input bandwidth Assigns shaped round robin (SRR) weights to an ingress queue. mls qos srr-queue input cos-map Maps class of service (CoS) values to an ingress queue or maps CoS values to a queue and to a threshold ID.
Page 378: Mls Qos Srr-Queue Input Cos-Map
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos srr-queue input cos-map mls qos srr-queue input cos-map Use the mls qos srr-queue input cos-map global configuration command on the switch stack or on a standalone switch to map class of service (CoS) values to an ingress queue or to map CoS values to a queue and to a threshold ID.
Page 379 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos srr-queue input cos-map You can map each CoS value to a different queue and threshold combination, allowing the frame to follow different behavior. Examples This example shows how to map CoS values 0 to 3 to ingress queue 1 and to threshold ID 1 with a drop threshold of 50 percent.
Page 380: Mls Qos Srr-Queue Input Dscp-Map
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos srr-queue input dscp-map mls qos srr-queue input dscp-map Use the mls qos srr-queue input dscp-map global configuration command on the switch stack or on a standalone switch to map Differentiated Services Code Point (DSCP) values to an ingress queue or to map DSCP values to a queue and to a threshold ID.
Page 381 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos srr-queue input dscp-map You can map each DSCP value to a different queue and threshold combination, allowing the frame to follow different behavior. You can map up to eight DSCP values per command.
Page 382: Mls Qos Srr-Queue Input Priority-Queue
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos srr-queue input priority-queue mls qos srr-queue input priority-queue Use the mls qos srr-queue input priority-queue global configuration command on the switch stack or on a standalone switch to configure the ingress priority queue and to guarantee bandwidth on the stack or internal ring if the ring is congested.
Page 383 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos srr-queue input priority-queue Examples This example shows how to assign the ingress bandwidths for the queues in the stack. Queue 1 is the priority queue with 10 percent of the bandwidth allocated to it. The bandwidth ratio allocated to queues 1 and 2 is 4/(4+4).
Page 384: Mls Qos Srr-Queue Input Threshold
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos srr-queue input threshold mls qos srr-queue input threshold Use the mls qos srr-queue input threshold global configuration command on the switch stack or on a standalone switch to assign weighted tail-drop (WTD) threshold percentages to an ingress queue.
Page 385 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos srr-queue input threshold Related Commands Command Description mls qos srr-queue input bandwidth Assigns shaped round robin (SRR) weights to an ingress queue. mls qos srr-queue input buffers Allocates the buffers between the ingress queues.
Page 386: Mls Qos Srr-Queue Output Cos-Map
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos srr-queue output cos-map mls qos srr-queue output cos-map Use the mls qos srr-queue output cos-map global configuration command on the switch stack or on a standalone switch to map class of service (CoS) values to an egress queue or to map CoS values to a queue and to a threshold ID.
Page 387 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos srr-queue output cos-map Usage Guidelines The drop-threshold percentage for threshold 3 is predefined. It is set to the queue-full state. The egress queue default settings are suitable for most situations. You should change them only when...
Page 388: Mls Qos Srr-Queue Output Dscp-Map
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos srr-queue output dscp-map mls qos srr-queue output dscp-map Use the mls qos srr-queue output dscp-map global configuration command on the switch stack or on a standalone switch to map Differentiated Services Code Point (DSCP) values to an egress or to map DSCP values to a queue and to a threshold ID.
Page 389 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos srr-queue output dscp-map Usage Guidelines The drop-threshold percentage for threshold 3 is predefined. It is set to the queue-full state. The egress queue default settings are suitable for most situations. You should change them only when...
Page 390: Mls Qos Trust
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos trust mls qos trust Use the mls qos trust interface configuration command on the switch stack or on a standalone switch to configure the port trust state. Ingress traffic can be trusted, and classification is performed by examining the packet Differentiated Services Code Point (DSCP), class of service (CoS), or IP-precedence field.
Page 391 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos trust The trusted boundary feature prevents security problems if users disconnect their PCs from networked Cisco IP Phones and connect them to the switch port to take advantage of trusted CoS or DSCP settings.
Page 392: Mls Qos Vlan-Based
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mls qos vlan-based mls qos vlan-based Use the mls qos vlan-based interface configuration command on the switch stack or on a standalone switch to enable VLAN-based quality of service (QoS) on the physical port. Use the no form of this command to disable this feature.
Page 393: Monitor Session
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands monitor session monitor session Use the monitor session global configuration command on the switch stack or on a standalone switch to start a new Switched Port Analyzer (SPAN) session or Remote SPAN (RSPAN) source or destination...
Page 394 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands monitor session untagged vlan vlan-id Accept incoming packets with untagged encapsulation with the specified VLAN as the default VLAN. vlan vlan-id When used with only the ingress keyword, set default VLAN for ingress traffic.
Page 395 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands monitor session Each session can include multiple ingress or egress source ports or VLANs, but you cannot combine source ports and source VLANs in a single session. Each session can include multiple destination ports.
Page 396 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands monitor session Examples This example shows how to create a local SPAN session 1 to monitor both sent and received traffic on source port 1 on stack member 1 to destination port 2 on stack member 2:...
Page 397: Mvr (Global Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mvr (global configuration) mvr (global configuration) Use the mvr global configuration command without keywords on the switch stack or on a standalone switch to enable the multicast VLAN registration (MVR) feature on the switch. Use the command with...
Page 398 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mvr (global configuration) Command Modes Global configuration Command History Release Modification 12.2(40)EX1 This command was introduced. Usage Guidelines A maximum of 256 MVR multicast groups can be configured on a switch.
Page 399 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mvr (global configuration) Related Commands Command Description mvr (interface configuration) Configures MVR ports. show mvr Displays MVR global parameters or port parameters. show mvr interface Displays the configured MVR interfaces with their type, status, and Immediate Leave configuration.
Page 400: Mvr (Interface Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mvr (interface configuration) mvr (interface configuration) Use the mvr interface configuration command on the switch stack or on a standalone switch to configure a Layer 2 port as a multicast VLAN registration (MVR) receiver or source port, to set the Immediate Leave feature, and to statically assign a port to an IP multicast VLAN and IP address.
Page 401 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands mvr (interface configuration) Receiver ports cannot be trunk ports. Receiver ports on a switch can be in different VLANs, but should not belong to the multicast VLAN.
Page 402: Network-Policy
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands network-policy network-policy Use the network-policy interface configuration command to apply a network-policy profile to an interface. Use the no form of this command to remove the policy.
Page 403: Network-Policy Profile (Global Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands network-policy profile (global configuration) network-policy profile (global configuration) Use the network-policy profile global configuration command to create a network-policy profile and to enter network-policy configuration mode. Use the no form of this command to delete the policy and to return to global configuration mode.
Page 404: Network-Policy Profile (Network-Policy Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands network-policy profile (network-policy configuration) network-policy profile (network-policy configuration) Use the network-policy profile configuration mode command to configure the network-policy profile created by using the network-policy profile global configuration command. Use the no form of this command without additional parameters to delete a profile.
Page 405 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands network-policy profile (network-policy configuration) This example shows how to configure the voice application type for VLAN 100 with a priority 4 CoS: Switch(config)# network-policy profile 1...
Page 406: Nmsp
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands nmsp nmsp Use the nmsp global configuration command to enable Network Mobility Services Protocol (NMSP) on the switch. This command is available only when your switch is running the cryptographic (encrypted) software image.
Page 407: Nmsp Attachment Suppress
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands nmsp attachment suppress nmsp attachment suppress Use the nmsp attachment suppress interface configuration mode command to suppress the reporting of attachment information from a specified interface. This command is available only when your switch is running the cryptographic (encrypted) software image.
Page 408: Nsf
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands Use the nsf router configuration command on a switch stack or standalone switch to enable and configure Cisco nonstop forwarding (NSF) for Open Shortest Path First (OSPF) or Enhanced Interior Gateway Routing Protocol (EIGRP) routing.
Page 409 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands Related Commands Command Description router protocol-id number Enables a routing process. Displays the current operating configuration. For syntax information, select Cisco IOS IP Command Reference, Volume 2 of 3: Routing Protocols, Release 12.2 > EIGRP Commands and Cisco IOS IP Command Reference, Volume 2 of 3: Routing Protocols, Release 12.2 >...
Page 410: Pagp Learn-Method
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands pagp learn-method pagp learn-method Use the pagp learn-method interface configuration command on the switch stack or on a standalone switch to learn the source address of incoming packets received from an EtherChannel port. Use the no form of this command to return to the default setting.
Page 411 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands pagp learn-method Examples This example shows how to set the learning method to learn the address on the physical port within the EtherChannel: Switch(config-if)# pagp learn-method physical-port...
Page 412: Pagp Port-Priority
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands pagp port-priority pagp port-priority Use the pagp port-priority interface configuration command on the switch stack or on a standalone switch to select a port over which all Port Aggregation Protocol (PAgP) traffic through the EtherChannel is sent.
Page 413 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands pagp port-priority Related Commands Command Description pagp learn-method Provides the ability to learn the source address of incoming packets. show pagp Displays PAgP channel-group information. show running-config Displays the operating configuration.
Page 414: Permit (Arp Access-List Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands permit (ARP access-list configuration) permit (ARP access-list configuration) Use the permit Address Resolution Protocol (ARP) access-list configuration command to permit an ARP packet based on matches against the Dynamic Host Configuration Protocol (DHCP) bindings. Use the no form of this command to remove the specified access control entry (ACE) from the access control list.
Page 415 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands permit (ARP access-list configuration) Command History Release Modification 12.2(40)EX1 This command was introduced. Usage Guidelines You can add permit clauses to forward ARP packets based on some matching criteria.
Page 416: Permit (Ipv6 Access-List Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands permit (IPv6 access-list configuration) permit (IPv6 access-list configuration) Use the permit IPv6 access list configuration command on the switch stack or on a standalone switch to set permit conditions for an IPv6 access list.
Page 417 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands permit (IPv6 access-list configuration) Syntax Description protocol Name or number of an Internet protocol. It can be one of the keywords ahp, esp, icmp, ipv6, pcp, sctp, tcp, or udp, or an integer in the range from 0 to 255 representing an IPv6 protocol number.
Page 418 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands permit (IPv6 access-list configuration) (Optional) Send an informational logging message to the console about the packet that matches the entry. (The level of messages logged to the console is controlled by the logging console command.)
Page 419 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands permit (IPv6 access-list configuration) Command History Release Modification 12.2(40)EX1 This command was introduced. Usage Guidelines The permit (IPv6 access-list configuration mode) command is similar to the permit (IPv4 access-list configuration mode) command, but it is IPv6-specific.
Page 420 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands permit (IPv6 access-list configuration) parameter-problem port-unreachable reassembly-timeout renum-command renum-result renum-seq-number router-advertisement router-renumbering router-solicitation time-exceeded unreachable Examples This example configures two IPv6 access lists named OUTBOUND and INBOUND and applies both access lists to outbound and inbound traffic on a Layer 3 interface.
Page 421: Permit (Mac Access-List Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands permit (MAC access-list configuration) permit (MAC access-list configuration) Use the permit MAC access-list configuration command on the switch stack or on a standalone switch to allow non-IP traffic to be forwarded if the conditions are matched. Use the no form of this command to remove a permit condition from the extended MAC access list.
Page 422 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands permit (MAC access-list configuration) lsap lsap-number mask (Optional) Use the LSAP number (0 to 65535) of a packet with 802.2 encapsulation to identify the protocol of the packet.
Page 423 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands permit (MAC access-list configuration) After an access control entry (ACE) is added to an access control list, an implied deny-any-any condition exists at the end of the list. That is, if there are no matches, the packets are denied. However, before the first ACE is added, the list permits all packets.
Page 424: Police
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands police police Use the police policy-map class configuration command on the switch stack or on a standalone switch to define a policer for classified traffic. A policer defines a maximum permissible rate of transmission, a maximum burst size for transmissions, and an action to take if either maximum is exceeded.
Page 425 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands police Examples This example shows how to configure a policer that drops packets if traffic exceeds 1 Mb/s average rate with a burst size of 20 KB. The DSCPs of incoming packets are trusted, and there is no packet modification.
Page 426: Police Aggregate
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands police aggregate police aggregate Use the police aggregate policy-map class configuration command on the switch stack or on a standalone switch to apply an aggregate policer to multiple classes in the same policy map. A policer defines a maximum permissible rate of transmission, a maximum burst size for transmissions, and an action to take if either maximum is exceeded.
Page 427 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands police aggregate Examples This example shows how to define the aggregate policer parameters and to apply the policer to multiple classes in a policy map: Switch(config)# mls qos aggregate-policer agg_policer1 10000 1000000 exceed-action drop...
Page 428: Policy-Map
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands policy-map policy-map Use the policy-map global configuration command on the switch stack or on a standalone switch to create or modify a policy map that can be attached to multiple physical ports or switch virtual interfaces (SVIs) and to enter policy-map configuration mode.
Page 429 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands policy-map Only one policy map per ingress port or SVI is supported. You can apply the same policy map to multiple physical ports or SVIs. You can apply a nonhierarchical policy maps to physical ports or to SVIs. However, you can only apply a hierarchical policy map to SVIs.
Page 430 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands policy-map Switch(config-pmap)# class cm-test-int Switch(config-pmap-c)# police 18000000 8000 exceed-action drop Switch(config-pmap-c)# exit Switch(config-pmap)# exit Switch(config)# policy-map pm-test-pm-2 Switch(config-pmap)# class cm-non-int Switch(config-pmap-c)# set dscp 7 Switch(config-pmap-c)# service-policy pm-test-int...
Page 431: Port-Channel Load-Balance
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands port-channel load-balance port-channel load-balance Use the port-channel load-balance global configuration command on the switch stack or on a standalone switch to set the load-distribution method among the ports in the EtherChannel. Use the no form of this command to return to the default setting.
Page 432 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands port-channel load-balance Related Commands Command Description interface port-channel Accesses or creates the port channel. show etherchannel Displays EtherChannel information for a channel. show running-config Displays the operating configuration. For syntax information, use this link to the Cisco IOS Release 12.2 Command Reference listing page:...
Page 433: Priority-Queue
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands priority-queue priority-queue Use the priority-queue interface configuration command to enable the egress expedite queue on a port. Use the no form of this command to return to the default setting.
Page 434 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands priority-queue This example shows how to disable the egress expedite queue after the SRR shaped and shared weights are configured. The shaped mode overrides the shared mode.
Page 435: Private-Vlan
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands private-vlan private-vlan Use the private-vlan VLAN configuration command on the switch stack or on a standalone switch to configure private VLANs and to configure the association between private-VLAN primary and secondary VLANs.
Page 436 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands private-vlan If you delete either the primary or secondary VLANs, the ports associated with the VLAN become • inactive. A community VLAN carries traffic among community ports and from community ports to the promiscuous ports on the corresponding primary VLAN.
Page 437 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands private-vlan Related Commands Command Description show interfaces status Displays the status of interfaces, including the VLANs to which they belong. show vlan private-vlan Displays the private VLANs and VLAN associations configured on the switch or switch stack.
Page 438: Private-Vlan Mapping
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands private-vlan mapping private-vlan mapping Use the private-vlan mapping interface configuration command on a switch virtual interface (SVI) on the switch stack or on a standalone switch to create a mapping between a private-VLAN primary and secondary VLANs so that both VLANs share the same primary VLAN SVI.
Page 439 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands private-vlan mapping Examples This example shows how to map the interface of VLAN 20 to the SVI of VLAN 18: Switch# configure terminal Switch# interface vlan 18...
Page 440: Queue-Set
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands queue-set queue-set Use the queue-set interface configuration command on the switch stack or on a standalone switch to map a port to a queue-set. Use the no form of this command to return to the default setting.
Page 441: Radius-Server Dead-Criteria
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands radius-server dead-criteria radius-server dead-criteria Use the radius-server dead-criteria global configuration command on the switch stack or on a standalone switch to configure the conditions that determine when a RADIUS server is considered unavailable or dead.
Page 442 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands radius-server dead-criteria Related Commands Command Description dot1x critical (global configuration) Configures the parameters for the inaccessible authentication bypass feature. dot1x critical (interface Enables the inaccessible authentication bypass feature on an...
Page 443: Radius-Server Host
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands radius-server host radius-server host Use the radius-server host global configuration command on the switch stack or on a standalone switch to configure the RADIUS server parameters, including the RADIUS accounting and authentication. Use the no form of this command to return to the default settings.
Page 444 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands radius-server host Usage Guidelines We recommend that you configure the UDP port for the RADIUS accounting server and the UDP port for the RADIUS authentication server to nondefault values.
Page 445: Reload
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands reload reload Use the reload privileged EXEC command to reload the stack member and to put a configuration change into effect. reload [LINE | at | cancel | in | slot stack-member-number | standby-cpu] Note This command is supported only on stacking-capable switches.
Page 446 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands reload Related Commands Command Description switch priority Changes the stack member priority value. switch renumber Changes the stack member number. show switch Displays information about the switch stack and its stack members.
Page 447: Remote Command
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands remote command remote command Use the remote command privileged EXEC command to monitor all or specified stack members. remote command {all | stack-member-number} LINE This command is supported only on stacking-capable switches.
Page 448 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands remote command Related Commands Command Description reload Accesses a specific stack member. switch priority Changes the stack member priority value. switch renumber Changes the stack member number.
Page 449: Remote-Span
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands remote-span remote-span Use the remote-span VLAN configuration command on the switch stack or on a standalone switch to configure a VLAN as a Remote Switched Port Analyzer (RSPAN) VLAN. Use the no form of this command to remove the RSPAN designation from the VLAN.
Page 450 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands remote-span Examples This example shows how to configure a VLAN as an RSPAN VLAN. Switch(config)# vlan 901 Switch(config-vlan)# remote-span This example shows how to remove the RSPAN feature from a VLAN.
Page 451: Renew Ip Dhcp Snooping Database
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands renew ip dhcp snooping database renew ip dhcp snooping database Use the renew ip dhcp snooping database privileged EXEC command on the switch stack or on a standalone switch to renew the DHCP snooping binding database.
Page 452 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands renew ip dhcp snooping database Related Commands Command Description ip dhcp snooping Enables DHCP snooping on a VLAN. ip dhcp snooping binding Configures the DHCP snooping binding database.
Page 453: Reserved-Only
Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands reserved-only reserved-only Use the reserved-only DHCP pool configuration mode command to allocate only reserved addresses in the Dynamic Host Configuration Protocol (DHCP) address pool. Use the no form of the command to return to the default.
Page 454 Chapter 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands reserved-only Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference 2-424 OL-13271-03...
Page 455: Rmon Collection Stats
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands rmon collection stats rmon collection stats Use the rmon collection stats interface configuration command on the switch stack or on a standalone switch to collect Ethernet group statistics, which include usage statistics about broadcast and multicast packets, and error statistics about cyclic redundancy check (CRC) alignment errors and collisions.
Page 456: Sdm Prefer
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands sdm prefer sdm prefer Use the sdm prefer global configuration command on the switch stack or on a standalone switch to configure the template used in Switch Database Management (SDM) resource allocation. You can use a template to allocate system resources to best support the features being used in your application.
Page 457 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands sdm prefer If a stack member cannot support the template that is running on the master switch, the switch goes • into SDM mismatch mode, the master switch does not attempt to change the SDM template, and the switch cannot be a functioning member of the stack.
Page 458 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands sdm prefer Table 2-16 lists the approximate number of each resource supported in each of the dual IPv4-and IPv6 templates for a desktop switch. Table 2-16 Approximate Feature Resources Allowed by Dual IPv4-IPv6 Templates Resource Default Routing...
Page 459: Service Password-Recovery
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands service password-recovery service password-recovery Use the service password-recovery global configuration command on the switch stack or on a standalone switch to enable the password-recovery mechanism (the default). This mechanism allows an end user with physical access to the switch to hold down the Mode button and interrupt the boot process while the switch is powering up and to assign a new password.
Page 460 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands service password-recovery If you use the no service password-recovery command to control end user access to passwords, we Note recommend that you save a copy of the config file in a location away from the switch in case the end user uses the password recovery procedure and sets the system back to default values.
Page 461: Service-Policy
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands service-policy service-policy Use the service-policy interface configuration command on the switch stack or on a standalone switch to apply a policy map defined by the policy-map command to the input of a physical port or a switch virtual interface (SVI).
Page 462 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands service-policy Examples This example shows how to apply plcmap1 to an physical ingress port: Switch(config)# interface gigabitethernet2/0/1 Switch(config-if)# service-policy input plcmap1 This example shows how to remove plcmap2 from a physical port: Switch(config)# interface gigabitethernet2/0/2 Switch(config-if)# no service-policy input plcmap2 This example shows how to apply plcmap1 to an ingress SVI when VLAN-based QoS is enabled:...
Page 463 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands service-policy Related Commands Command Description policy-map Creates or modifies a policy map that can be attached to multiple ports to specify a service policy. show policy-map Displays QoS policy maps. show running-config Displays the operating configuration.
Page 464: Session
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands session session Use the session privileged EXEC command on the stack master to access a specific stack member. session stack-member-number Syntax Description stack-member-number Specify the stack member number. The range is 1 to 9. Defaults No default is defined.
Page 465: Set
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands Use the set policy-map class configuration command on the switch stack or on a standalone switch to classify IP traffic by setting a Differentiated Services Code Point (DSCP) or an IP-precedence value in the packet.
Page 466 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands Examples This example shows how to assign DSCP 10 to all FTP traffic without any policers: Switch(config)# policy-map policy_ftp Switch(config-pmap)# class ftp_class Switch(config-pmap-c)# set dscp 10 Switch(config-pmap)# exit You can verify your settings by entering the show policy-map privileged EXEC command.
Page 467: Setup
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands setup setup Use the setup privileged EXEC command to configure the switch with its initial configuration. setup Syntax Description This command has no arguments or keywords. Command Modes Privileged EXEC Command History Release...
Page 468 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands setup Enter host name [Switch]:host-name The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration. Enter enable secret: enable-secret-password The enable password is used when you do not specify an enable secret password, with some older software versions, and...
Page 469 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands setup Use this configuration? [yes/no]: yes [0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit. Enter your selection [2]: Related Commands Command...
Page 470: Setup Express
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands setup express setup express Use the setup express global configuration command to enable Express Setup mode on the switch stack or on a standalone switch. Use the no form of this command to disable Express Setup mode. setup express no setup express Syntax Description...
Page 471 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands setup express Examples This example shows how to enable Express Setup mode: Switch(config)# setup express You can verify that Express Setup mode is enabled by pressing the Mode button: On an unconfigured switch, the LEDs above the Mode button turn solid green after 3 seconds.
Page 472: Show Access-Lists
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show access-lists show access-lists Use the show access-lists privileged EXEC command to display access control lists (ACLs) configured on the switch. show access-lists [name | number | hardware counters | ipc] [ | {begin | exclude | include} expression] Syntax Description name...
Page 473 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show access-lists Examples This is an example of output from the show access-lists command: Switch# show access-lists Standard IP access list 1 10 permit 1.1.1.1 20 permit 2.2.2.2 30 permit any 40 permit 0.255.255.255, wildcard bits 12.0.0.0 Standard IP access list videowizard_1-1-1-1...
Page 474 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show access-lists L2 ACL OUTPUT Statistics Drop: All frame count: 0 Drop: All bytes count: 0 Drop And Log: All frame count: 0 Drop And Log: All bytes count: 0 Bridge Only: All frame count: 0 Bridge Only:...
Page 475: Show Archive Status
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show archive status show archive status Use the show archive status privileged EXEC command to display the status of a new image being downloaded to a switch with the HTTP or the TFTP protocol. show archive status [ | {begin | exclude | include} expression] Syntax Description | begin...
Page 476: Show Arp Access-List
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show arp access-list show arp access-list Use the show arp access-list user EXEC command to display detailed information about Address Resolution Protocol (ARP) access control (lists). show arp access-list [acl-name] [ | {begin | exclude | include} expression] This command is supported only if your switch is running the IP services feature set.
Page 477: Show Authentication
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show authentication show authentication Use the show authentication command (in either user EXEC or privileged EXEC mode) to display information about authentication manager events on the switch. show authentication {interface interface-id | registrations | sessions [session-id session-id] [handle handle] [interface interface-id] [mac mac] [method method]} Syntax Description interface interface-id...
Page 478 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show authentication Table 2-17 show authentication Command Output (continued) Field Description Authc Success A method has resulted in authentication success for this session. Authc Failed A method has resulted in authentication fail for this session. Authz Success All features have been successfully applied for this session.
Page 479 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show authentication This is an examle of the show authentication sessions command for a specified interface: Switch# show authentication sessions int gi 3/46 Interface: GigabitEthernet3/46 MAC Address: Unknown IP Address: Unknown Status:...
Page 480 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show authentication authentication Adds an authentication method to the port-priority list. priority authentication timer Configures the timeout and reauthentication parameters for an 802.1x-enabled port. authentication Configures the violation modes that occur when a new device connects to a violation port or when a new device connects to a port with the maximum number of devices already connected to that port.
Page 481: Show Auto Qos
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show auto qos show auto qos Use the show auto qos user EXEC command to display the quality of service (QoS) commands entered on the interfaces on which automatic QoS (auto-QoS) is enabled. show auto qos [interface [interface-id]] Syntax Description interface [interface-id]...
Page 482 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show auto qos This is an example of output from the show auto qos interface interface-id command when the auto qos voip cisco-phone interface configuration command is entered: Switch>...
Page 483 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show auto qos class-map match-all AutoQoS-VoIP-RTP-Trust match ip dscp ef class-map match-all AutoQoS-VoIP-Control-Trust match ip dscp cs3 af31 policy-map AutoQoS-Police-SoftPhone class AutoQoS-VoIP-RTP-Trust set dscp ef police 320000 8000 exceed-action policed-dscp-transmit class AutoQoS-VoIP-Control-Trust set dscp cs3 police 32000 8000 exceed-action policed-dscp-transmit...
Page 484 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show auto qos This is an example of output from the show auto qos interface interface-id command when the auto qos voip cisco-phone interface configuration command is entered: Switch>...
Page 485: Show Boot
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show boot show boot Use the show boot privileged EXEC command to display the settings of the boot environment variables. show boot [ | {begin | exclude | include} expression] Syntax Description | begin (Optional) Display begins with the line that matches the expression.
Page 486 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show boot Table 2-19 describes each field in the display. Table 2-19 show boot Field Descriptions Field Description BOOT path-list Displays a semicolon separated list of executable files to try to load and execute when automatically booting.
Page 487 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show boot Related Commands Command Description boot auto-copy-sw Enables the automatic upgrade (auto-upgrade) process to automatically upgrade a switch in version-mismatch (VM) mode. boot Specifies the software image to use in the auto-upgrade process. auto-download-sw boot config-file Specifies the filename that Cisco IOS uses to read and write a nonvolatile...
Page 488: Show Cable-Diagnostics Tdr
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show cable-diagnostics tdr show cable-diagnostics tdr Use the show cable-diagnostics tdr privileged EXEC command to display the Time Domain Reflector (TDR) results. show cable-diagnostics tdr interface interface-id [ | {begin | exclude | include} expression] Syntax Description interface-id Specify the interface on which TDR was run.
Page 489 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show cable-diagnostics tdr Table 2-20 Fields Descriptions for the show cable-diagnostics tdr Command Output (continued) Field Description Pair length Location on the cable where the problem is, with respect to your switch. TDR can only find the location in one of these cases: The cable is properly connected, the link is up, and the interface speed is •...
Page 490: Show Cisp
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show cisp show cisp Use the show cisp privileged EXEC command to display CISP information for a specified interface. show cisp {[interface interface-id] | clients | summary} | {[begin | exclude | include} expression]} Syntax Description clients (Optional) Display CISP client details...
Page 491: Show Class-Map
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show class-map show class-map Use the show class-map user EXEC command to display quality of service (QoS) class maps, which define the match criteria to classify traffic. show class-map [class-map-name] [ | {begin | exclude | include} expression] Syntax Description class-map-name (Optional) Display the contents of the specified class map.
Page 492: Show Controllers Cpu-Interface
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show controllers cpu-interface show controllers cpu-interface Use the show controllers cpu-interface privileged EXEC command to display the state of the CPU network interface ASIC and the send and receive statistics for packets reaching the CPU. show controllers cpu-interface [ | {begin | exclude | include} expression] Syntax Description | begin...
Page 493 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show controllers cpu-interface Supervisor ASIC receive-queue parameters ---------------------------------------- queue 0 maxrecevsize 5EE pakhead 1419A20 paktail 13EAED4 queue 1 maxrecevsize 5EE pakhead 15828E0 paktail 157FBFC queue 2 maxrecevsize 5EE pakhead 1470D40 paktail 1470FE4 queue 3 maxrecevsize 5EE pakhead 19CDDD0 paktail 19D02C8 <output truncated>...
Page 494: Show Controllers Ethernet-Controller
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show controllers ethernet-controller show controllers ethernet-controller Use the show controllers ethernet-controller privileged EXEC command without keywords to display per-interface send and receive statistics read from the hardware. Use with the phy keyword to display the interface internal registers or the port-asic keyword to display information about the port ASIC.
Page 495 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show controllers ethernet-controller Examples This is an example of output from the show controllers ethernet-controller command for an interface. Table 2-21 describes the Transmit fields, and Table 2-22 describes the Receive fields.
Page 496 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show controllers ethernet-controller Table 2-21 Transmit Field Descriptions (continued) Field Description 5 collision frames The number of frames that are successfully sent on an interface after five collisions occur. 6 collision frames The number of frames that are successfully sent on an interface after six collisions occur.
Page 497 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show controllers ethernet-controller Table 2-22 Receive Field Descriptions (continued) Field Description Unicast bytes The total amount of memory (in bytes) used by unicast frames received on an interface, including the FCS value and the incorrectly formed frames.
Page 498 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show controllers ethernet-controller Table 2-22 Receive Field Descriptions (continued) Field Description System FCS error frames The total number of frames received on an interface that have a valid length (in bytes) but that do not have the correct FCS values.
Page 499 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show controllers ethernet-controller Bit encoding:0x1 =NRZ Normal BitRate in multiple of 1M b/s :0x2848 Protocol Type:0x1 =10GgE Standards Compliance Codes : 10GbE Code Byte 0 :0x4 =10GBASE-ER 10GbE Code Byte 1 :0x0 SONET/SDH Code Byte 0:0x0 SONET/SDH Code Byte 1:0x0 SONET/SDH Code Byte 2:0x0...
Page 500: Show Controllers Tcam
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show controllers ethernet-controller This is an example of output from the show controllers ethernet-controller port-asic statistics command: Switch# show controllers ethernet-controller port-asic statistics =========================================================================== Switch 1, PortASIC 0 Statistics --------------------------------------------------------------------------- 0 RxQ-0, wt-0 enqueue frames 0 RxQ-0, wt-0 drop frames...
Page 501: Show Controllers Ethernet-Controller Fastethernet
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show controllers ethernet-controller fastethernet show controllers ethernet-controller fastethernet Use the show controllers ethernet-controller fastethernet privileged EXEC command to display information about the Ethernet management port, including the port status and the per-interface send and receive statistics read from the hardware.
Page 502 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show controllers ethernet-controller fastethernet Examples This is an example of output from the show controllers ethernet-controller fastethernet 0 command. Table 2-21 Table 2-22 for descriptions of the Transmit and Receive fields. Switch>...
Page 503 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show controllers ethernet-controller fastethernet malrxeobisr 0x80000000 0x112 malrxdeir 0x00000000 0x113 maltxctp0r 0x0F027880 0x120 malrxctp0r 0x0F0272C0 0x140 malrcbs0 0x00000060 0x160 <output truncated> This is an example of output from the show controllers ethernet-controller fastethernet 0 stack command on a stack member: Switch# show controller ethernet-controller fastethernet 0 stack Switch...
Page 504: Show Controllers Tcam
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show controllers tcam show controllers tcam Use the show controllers tcam privileged EXEC command to display the state of the registers for all hardware memory in the system and for all hardware interface ASICs that are content-addressable memory-controllers.
Page 505 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show controllers tcam Examples This is an example of output from the show controllers tcam command: Switch# show controllers tcam ------------------------------------------------------------------------ TCAM-0 Registers ------------------------------------------------------------------------ REV: 00B30103 SIZE: 00080040 00000000 CCR: 00000000_F0000020...
Page 506: Show Controllers Utilization
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show controllers utilization show controllers utilization Use the show controllers utilization user EXEC command to display bandwidth utilization on the switch or specific ports. show controllers [interface-id] utilization [ | {begin | exclude | include} expression] Syntax Description interface-id (Optional) ID of the switch interface.
Page 507 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show controllers utilization Table 2-23 defines the field descriptions in the output. Table 2-23 show controllers utilization Field Descriptions Field Description Receive Bandwidth Percentage Displays the received bandwidth usage of the switch, which is the Utilization sum of the received traffic on all the ports divided by the switch receive capacity.
Page 508: Show Diagnostic
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show diagnostic show diagnostic Use the show diagnostic user EXEC command to display the online diagnostic test results and the supported test suites. show diagnostic content switch [number | all] [ | {begin | exclude | include} expression] show diagnostic post [ |{begin | exclude | include} expression] show diagnostic result switch [number | all] [detail | test {name | test-id | test-id-range | all} [detail]] [ | {begin | exclude | include} expression]...
Page 509 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show diagnostic status Display the running diagnostic tests. | begin (Optional) Display begins with the line that matches the expression. | exclude (Optional) Display excludes lines that match the expression. | include (Optional) Display includes lines that match the specified expression.
Page 510 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show diagnostic 4) TestPortAsicRingLoopback --------> B*D*X**IR* not configured n/a 5) TestMicRingLoopback -------------> B*D*X**IR* not configured n/a 6) TestPortAsicMem -----------------> B*D*X**IR* not configured n/a This example shows how to display the running tests in a switch stack: Switch>...
Page 511 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show diagnostic Last test failure time ------> n/a Last test pass time ---------> n/a Total failure count ---------> 0 Consecutive failure count ---> 0 ___________________________________________________________________________ 3) TestPortAsicCam -----------------> U Error code ------------------>...
Page 512 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show diagnostic Last test pass time ---------> n/a Total failure count ---------> 0 Consecutive failure count ---> 0 __________________________________________________________________________ Related Commands Command Description diagnostic monitor Configures teh health-monitoring diagnostic test. diagnostic schedule Sets the scheduling of test-based online diagnostic testing.
Page 513: Show Dot1Q-Tunnel
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show dot1q-tunnel show dot1q-tunnel Use the show dot1q-tunnel user EXEC command to display information about IEEE 802.1Q tunnel ports. show dot1q-tunnel [interface interface-id] [ | {begin | exclude | include} expression] Syntax Description interface interface-id (Optional) Specify the interface for which to display IEEE 802.1Q tunneling...
Page 514: Show Dot1X
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show dot1x show dot1x Use the show dot1x user EXEC command to display IEEE 802.1x statistics, administrative status, and operational status for the switch or for the specified port. show dot1x [{all [summary] | interface interface-id} [details | statistics]] [ | {begin | exclude | include} expression] Syntax Description...
Page 515 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show dot1x This is an example of output from the show dot1x all user EXEC command: Switch> show dot1x all Sysauthcontrol Enabled Dot1x Protocol Version Critical Recovery Delay Critical EAPOL Disabled Dot1x Info for GigabitEthernet1/0/1...
Page 516 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show dot1x This is an example of output from the show dot1x interface interface-id details user EXEC command: Switch# show dot1x interface gigabitethernet1/0/2 details Dot1x Info for GigabitEthernet1/0/2 ----------------------------------- = AUTHENTICATOR PortControl...
Page 517 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show dot1x Table 2-24 describes the fields in the display. Table 2-24 show dot1x statistics Field Descriptions Field Description RxStart Number of valid EAPOL-start frames that have been received. RxLogoff Number of EAPOL-logoff frames that have been received.
Page 518: Show Dtp
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show dtp show dtp Use the show dtp privileged EXEC command to display Dynamic Trunking Protocol (DTP) information for the switch or for a specified interface. show dtp [interface interface-id] [ | {begin | exclude | include} expression] Syntax Description interface (Optional) Display port security settings for the specified interface.
Page 519 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show dtp ---------- 3160 packets received (3160 good) 0 packets dropped 0 nonegotiate, 0 bad version, 0 domain mismatches, 0 bad TLVs, 0 other 6320 packets output (6320 good) 3160 native, 3160 software encap isl, 0 isl hardware native 0 output errors 0 trunk timeouts...
Page 520: Show Eap
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show eap show eap Use the show eap privileged EXEC command to display Extensible Authentication Protocol (EAP) registration and session information for the switch or for the specified port. show eap {{registrations [method [name] | transport [name]]} | {sessions [credentials name [interface interface-id] | interface interface-id | method name | transport name]}} [credentials name | interface interface-id | transport name] [ | {begin | exclude | include}...
Page 521 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show eap Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain Output appear. Examples This is an example of output from the show eap registrations privileged EXEC command: Switch>...
Page 522 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show eap This is an example of output from the show eap sessions interface interface-id privileged EXEC command: Switch# show eap sessions gigabitethernet1/0/1 Role: Authenticator Decision: Fail Lower layer: Dot1x-AuthenticaInterface: Gi1/0/1 Current method:...
Page 523: Show Energywise
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show energywise show energywise Use the show energywise privileged EXEC command to display the EnergyWise settings, the status of the entity, and the status of the power over Ethernet (PoE) ports. show energywise neighbors [categories | children | domain | events | level [children | current [children] | delta | delta children] | neighbors | recurrences | statistics | usage [children] | version] [ | {begin | exclude | include} expression]...
Page 524 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show energywise Usage Guidelines Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output do not appear, but the lines that contain Output appear. Examples Switch# show energywise Interface...
Page 525 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show energywise Switch# show energywise level current Interface Name Level Value --------- ---- ----- ----- lobby.1 558.0 (W) Switch# show energywise level current children Interface Name Level Value --------- ---- -----...
Page 526 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show energywise Switch# show energywise usage child Interface Name Usage Caliber --------- ---- _____ _______ lobby.1 558.0 (W) Gi1/0/1 Gi1.0.1 presumed Gi1/0/2 Gi1.0.2 presumed Gi1/0/3 Gi1.0.3 presumed Gi1/0/4 Gi1.0.4 presumed Gi1/0/5...
Page 527: Show Env
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show env show env Use the show env user EXEC command to display fan, temperature, and power information for the switch or the switch stack. show env {all | | stack [switch-number] | temperature [status]} [ | {begin | exclude | include} expression] Syntax Description Display the fan and temperature environmental status and the status of the internal...
Page 528 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show env Examples This is an example of output from the show env all command on a standalone switch: Switch> show env all This is an example of output from the show env stack command: Switch>...
Page 529: Show Errdisable Detect
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show errdisable detect show errdisable detect Use the show errdisable detect user EXEC command to display error-disabled detection status. show errdisable detect [ | {begin | exclude | include} expression] Syntax Description | begin (Optional) Display begins with the line that matches the expression.
Page 530 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show errdisable detect Examples This is an example of output from the show errdisable detect command: Switch> show errdisable detect ErrDisable Reason Detection Mode ----------------- --------- ---- arp-inspection Enabled port bpduguard...
Page 531: Show Errdisable Flap-Values
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show errdisable flap-values show errdisable flap-values Use the show errdisable flap-values user EXEC command to display conditions that cause an error to be recognized for a cause. show errdisable flap-values [ | {begin | exclude | include} expression] Syntax Description | begin (Optional) Display begins with the line that matches the expression.
Page 532: Show Errdisable Recovery
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show errdisable recovery show errdisable recovery Use the show errdisable recovery user EXEC command to display the error-disabled recovery timer information. show errdisable recovery [ | {begin | exclude | include} expression] Syntax Description | begin (Optional) Display begins with the line that matches the expression.
Page 533 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show errdisable recovery Interface Errdisable reason Time left(sec) --------- ----------------- -------------- Gi1/0/2 link-flap Though visible in the output, the unicast-flood field is not valid. Note Related Commands Command Description errdisable recovery Configures the recover mechanism variables.
Page 534: Show Etherchannel
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show etherchannel show etherchannel Use the show etherchannel user EXEC command to display EtherChannel information for a channel. show etherchannel [channel-group-number {detail | port | port-channel | protocol | summary}] {detail | load-balance | port | port-channel | protocol | summary} [ | {begin | exclude | include} expression] Syntax Description...
Page 535 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show etherchannel Examples This is an example of output from the show etherchannel 1 detail command: Switch> show etherchannel 1 detail Group state = L2 Ports: 2 Maxports = 16 Port-channels: 1 Max Port-channels = 16 Protocol: LACP...
Page 536 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show etherchannel This is an example of output from the show etherchannel 1 summary command: Switch> show etherchannel 1 summary Flags: D - down P - in port-channel I - stand-alone s - suspended H - Hot-standby (LACP only) R - Layer3...
Page 537: Show Fallback Profile
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show fallback profile show fallback profile Use the show fallback profile privileged EXEC command to display the fallback profiles that are configured on a switch. show fallback profile [append | begin | exclude | include | {[redirect | tee] url} expression] Syntax Description | append (Optional) Append redirected output to a specified URL...
Page 538 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show fallback profile Related Commands Command Description dot1x fallback Configure a port to use web authentication as a fallback method for clients that do not support IEEE 802.1x authentication. fallback profile Create a web authentication fallback profile.
Page 539: Show Flowcontrol
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show flowcontrol show flowcontrol Use the show flowcontrol user EXEC command to display the flow control status and statistics. show flowcontrol [interface interface-id | module number] [ | {begin | exclude | include} expression] Syntax Description interface interface-id...
Page 540 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show flowcontrol Examples This is an example of output from the show flowcontrol command. Switch> show flowcontrol Port Send FlowControl Receive FlowControl RxPause TxPause admin oper admin oper --------- -------- -------- -------- -------- ------- -------...
Page 541: Show Idprom
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show idprom show idprom Use the show idprom user EXEC command to display the IDPROM information for the specified interface. show idprom {interface interface-id} [detail] [ | {begin | exclude | include} expression] Syntax Description interface interface-id Display the IDPROM information for the specified interface.
Page 542 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show idprom SONET/SDH Code Byte 1 :0x0 SONET/SDH Code Byte 2 :0x0 SONET/SDH Code Byte 3 :0x0 10GFC Code Byte 0 :0x0 10GFC Code Byte 1 :0x0 10GFC Code Byte 2 :0x0 10GFC Code Byte 3 :0x0 Transmission range in 10m :0x0 Fibre Type :...
Page 543: Show Interfaces
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show interfaces show interfaces Use the show interfaces privileged EXEC command to display the administrative and operational status of all interfaces or a specified interface. show interfaces [interface-id | vlan vlan-id] [accounting | capabilities [module number] | counters | description | etherchannel | flowcontrol | private-vlan mapping | pruning | stats | status [err-disabled] | switchport [backup | module number] | transceiver [properties | detail] [module number] | transceiver {tengigabitethernet interface-id} | properties | detail...
Page 544 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show interfaces transceiver (Optional) Display the physical properties of a coarse wavelength-division [detail | multiplexer (CWDM) or dense wavelength-division multiplexer (DWDM) small properties] form-factor (SFP) module interface. The keywords have these meanings: detail—(Optional) Display calibration properties, including high and low •...
Page 545 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show interfaces se the show interface switchport module number command to display the switch port • characteristics of all interfaces on that switch in the stack. If there is no switch with that module number in the stack, there is no output.
Page 546 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show interfaces No traffic sent or received on this interface. <output truncated> This is an example of output from the show interfaces capabilities command for an interface. Switch# show interfaces gigabitethernet1/0/2 capabilities GigabitEthernet1/0/2 Model: WS-CBS3130G...
Page 547 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show interfaces This is an example of output from the show interfaces private-vlan mapping command when the private-VLAN primary VLAN is VLAN 10 and the secondary VLANs are VLANs 501 and 502: Switch# show interfaces private-vlan mapping Interface Secondary VLAN Type --------- -------------- -----------------...
Page 548 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show interfaces This is an example of output from the show interfaces status err-disabled command. It displays the status of interfaces in the error-disabled state. Switch# show interfaces status err-disabled Port Name Status...
Page 549 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show interfaces Table 2-26 show interfaces switchport Field Descriptions (continued) Field Description Access Mode VLAN Displays the VLAN ID to which the port is configured. Trunking Native Mode VLAN Lists the VLAN ID of the trunk that is in native mode.
Page 550 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show interfaces This is an example of output from the show interfaces switchport backup command: Switch# show interfaces switchport backup Switch Backup Interface Pairs: Active Interface Backup Interface State -------------------------------------------------------------- Gi1/0/1...
Page 551 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show interfaces This is an example of out put from the show interfaces switchport backup command when a Flex Link interface goes down (LINK_DOWN), and VLANs preferred on this interface are moved to the peer interface of the Flex Link pair.
Page 552 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show interfaces High Alarm High Warn Low Warn Low Alarm Current Threshold Threshold Threshold Threshold Port (milliamperes) (mA) (mA) (mA) (mA) ------- ----------------- ---------- --------- --------- --------- Gi2/0/3 31.0 84.0 70.0...
Page 553 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show interfaces Optical High Alarm High Warn Low Warn Low Alarm Receive Power Threshold Threshold Threshold Threshold Port (dBm) (dBm) (dBm) (dBm) (dBm) ------- ----------------- ---------- --------- --------- --------- Gi2/0/3 ( -0.0) --...
Page 554 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show interfaces Related Commands Command Description switchport access Configures a port as a static-access or a dynamic-access port. switchport block Blocks unknown unicast or multicast traffic on an interface. switchport backup interface Configures Flex Links, a pair of Layer 2 interfaces that provide mutual backup.
Page 555: Show Interfaces Counters
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show interfaces counters show interfaces counters Use the show interfaces counters privileged EXEC command to display various counters for the switch or for a specific interface. show interfaces [interface-id | vlan vlan-id] counters [errors | etherchannel | module switch- number | protocol status | trunk] [ | {begin | exclude | include} expression] Syntax Description interface-id...
Page 556 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show interfaces counters Examples This is an example of partial output from the show interfaces counters command. It displays all counters for the switch. Switch# show interfaces counters Port InOctets InUcastPkts...
Page 557 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show interfaces counters This is an example of output from the show interfaces counters trunk command. It displays trunk counters for all interfaces. Switch# show interfaces counters trunk Port TrunkFramesTx TrunkFramesRx...
Page 558: Show Inventory
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show inventory show inventory Use the show inventory user EXEC command to display product identification (PID) information for the hardware. show inventory [entity-name | raw] [ | {begin | exclude | include} expression] Syntax Description entity-name (Optional) Display the specified entity.
Page 559 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show inventory NAME: ''Switch 2 - Slot 1'', DESCR: ''TwinGig Converter Module'' PID: 800-27645-01 A , VID: A0 , SN: CAT1113545M NAME: ''Switch 2 - Slot 2'', DESCR: ''TwinGig Converter Module'' PID: 800-27645-01 A , VID: A0 , SN: CAT11115UVM This is example output from the show inventory command on a nonstacking-capable switch:...
Page 560: Show Ip Arp Inspection
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip arp inspection show ip arp inspection Use the show ip arp inspection privileged EXEC command to display the configuration and the operating state of dynamic Address Resolution Protocol (ARP) inspection or the status of this feature for all VLANs or for the specified interface or VLAN.
Page 561 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip arp inspection Usage Guidelines Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain Output are displayed. Examples This is an example of output from the show ip arp inspection command Switch# show ip arp inspection...
Page 562 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip arp inspection Gi1/0/1 0001.c940.1111 10.10.10.1 DHCP Deny 19:39:03 UTC Mon Mar 1 1993 Gi1/0/1 0001.c940.1112 10.10.10.2 DHCP Deny 19:39:04 UTC Mon Mar 1 1993 Gi1/0/1 0001.c940.1114 173.1.1.1 DHCP Deny 19:39:06 UTC...
Page 563 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip arp inspection This is an example of output from the show ip arp inspection vlan 5 command. It shows the configuration and the operating state of dynamic ARP inspection for VLAN 5. Switch# show ip arp inspection vlan 5 Source Mac Validation :Enabled...
Page 564: Show Ip Dhcp Snooping
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip dhcp snooping show ip dhcp snooping Use the show ip dhcp snooping user EXEC command to display the DHCP snooping configuration. show ip dhcp snooping [ | {begin | exclude | include} expression] Syntax Description | begin (Optional) Display begins with the line that matches the expression.
Page 565: Show Ip Dhcp Snooping Binding
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip dhcp snooping binding show ip dhcp snooping binding Use the show ip dhcp snooping binding user EXEC command to display the DHCP snooping binding database and configuration information for all interfaces on a switch. show ip dhcp snooping binding [ip-address] [mac-address] [interface interface-id] [vlan vlan-id] [ | {begin | exclude | include} expression] Syntax Description...
Page 566 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip dhcp snooping binding This example shows how to display the DHCP snooping binding entries for a specific IP address: Switch> show ip dhcp snooping binding 10.1.2.150 MacAddress IpAddress Lease(sec)
Page 567: Show Ip Dhcp Snooping Database
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip dhcp snooping database show ip dhcp snooping database Use the show ip dhcp snooping database user EXEC command to display the status of the DHCP snooping binding database agent. show ip dhcp snooping database [detail] [ | {begin | exclude | include} expression] This command is supported only if your switch is running the IP services feature set.
Page 568 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip dhcp snooping database This is an example of output from the show ip dhcp snooping database detail command: Switch# show ip dhcp snooping database detail Agent URL : tftp://10.1.1.1/directory/file Write delay Timer : 300 seconds Abort Timer : 300 seconds Agent Running : No...
Page 569: Show Ip Dhcp Snooping Statistics
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip dhcp snooping statistics show ip dhcp snooping statistics Use the show ip dhcp snooping statistics user EXEC command to display DHCP snooping statistics in summary or detail form. show ip dhcp snooping statistics [detail] [ | {begin | exclude | include} expression] Syntax Description detail...
Page 570 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip dhcp snooping statistics Table 2-28 shows the DHCP snooping statistics and their descriptions: Table 2-28 DHCP Snooping Statistics DHCP Snooping Statistic Description Packets Processed by DHCP Snooping Total number of packets handled by DHCP snooping, including forwarded and dropped packets.
Page 571 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip dhcp snooping statistics Table 2-28 DHCP Snooping Statistics (continued) DHCP Snooping Statistic Description Insertion of opt82 fail Number of times the option-82 insertion into a packet failed. The insertion might fail if the packet with the option-82 data exceeds the size of a single physical packet on the internet.
Page 572: Show Ip Igmp Profile
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip igmp profile show ip igmp profile Use the show ip igmp profile privileged EXEC command to display all configured Internet Group Management Protocol (IGMP) profiles or a specified IGMP profile. show ip igmp profile [profile number] [ | {begin | exclude | include} expression] Syntax Description profile number...
Page 573: Show Ip Igmp Snooping
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip igmp snooping show ip igmp snooping Use the show ip igmp snooping user EXEC command to display the Internet Group Management Protocol (IGMP) snooping configuration of the switch or the VLAN. show ip igmp snooping [groups | mrouter | querier] [vlan vlan-id] [ | {begin | exclude | include} expression] Syntax Description...
Page 574 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip igmp snooping Vlan 1: -------- IGMP snooping :Enabled Immediate leave :Disabled Multicast router learning mode :pim-dvmrp Source only learning age timer CGMP interoperability mode :IGMP_ONLY Last member query interval : 100 This is an example of output from the show ip igmp snooping command.
Page 575 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip igmp snooping Related Commands Command Description ip igmp snooping Enables IGMP snooping on the switch or on a VLAN. ip igmp snooping Enables the IGMP snooping configurable-leave timer. last-member-query-interval ip igmp snooping querier Enables the IGMP querier function in Layer 2 networks.
Page 576: Show Ip Igmp Snooping Groups
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip igmp snooping groups show ip igmp snooping groups Use the show ip igmp snooping groups privileged EXEC command to display the Internet Group Management Protocol (IGMP) snooping multicast table for the switch or the multicast information. Use with the vlan keyword to display the multicast table for a specified multicast VLAN or specific multicast information.
Page 577 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip igmp snooping groups Examples This is an example of output from the show ip igmp snooping groups command without any keywords. It displays the multicast table for the switch. Switch# show ip igmp snooping groups Vlan Group...
Page 578: Show Ip Igmp Snooping Mrouter
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip igmp snooping mrouter show ip igmp snooping mrouter Use the show ip igmp snooping mrouter privileged EXEC command to display the Internet Group Management Protocol (IGMP) snooping dynamically learned and manually configured multicast router ports for the switch or for the specified multicast VLAN.
Page 579 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip igmp snooping mrouter Related Commands Command Description ip igmp snooping Enables IGMP snooping on the switch or on a VLAN. ip igmp snooping vlan mrouter Adds a multicast router port. ip igmp snooping vlan static Statically adds a Layer 2 port as a member of a multicast group.
Page 580: Show Ip Igmp Snooping Querier
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip igmp snooping querier show ip igmp snooping querier Use the show ip igmp snooping querier detail user EXEC command to display the configuration and operation information for the IGMP querier configured on a switch. show ip igmp snooping querier [detail | vlan vlan-id [detail]] [ | {begin | exclude | include} expression] Syntax Description...
Page 581 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip igmp snooping querier Examples This is an example of output from the show ip igmp snooping querier command: Switch> show ip igmp snooping querier Vlan IP Address IGMP Version Port ---------------------------------------------------...
Page 582: Show Ip Source Binding
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip source binding show ip source binding Use the show ip source binding user EXEC command to display the IP source bindings on the switch. show ip source binding [ip-address] [mac-address] [dhcp-snooping | static] [interface interface-id] [vlan vlan-id] [ | {begin | exclude | include} expression] This command is supported only if your switch is running the IP services feature set.
Page 583 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip source binding Related Commands Command Description ip dhcp snooping binding Configures the DHCP snooping binding database. ip source binding Configures static IP source bindings on the switch. Cisco Catalyst Blade Switch 3120 for HP Command Reference 2-553 OL-12248-03...
Page 584: Show Ip Verify Source
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip verify source show ip verify source Use the show ip verify source user EXEC command to display the IP source guard configuration on the switch or on a specific interface. show ip verify source [interface interface-id] [ | {begin | exclude | include} expression] Syntax Description interface interface-id...
Page 585 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ip verify source On the Gigabit Ethernet 1/0/4 interface, IP source guard with source IP and MAC address filtering • is enabled, and static IP source bindings are configured on VLANs 10 and 11. For VLANs 12 to 20, the default port ACL is applied on the interface for the VLANs on which IP source guard is not configured.
Page 586: Show Ipc
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ipc show ipc Use the show ipc user EXEC command to display Interprocess Communications Protocol (IPC) configuration, status, and statistics on a switch stack or a standalone switch. show ipc {mcast {appclass | groups | status} | nodes | ports [open] | queue | rpc | session {all | rx | tx} [verbose] | status [cumlulative] | zones} [ | {begin | exclude | include} expression] Syntax Description...
Page 587 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ipc Usage Guidelines Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output do not appear, but the lines that contain Output appear. Examples This example shows how to display the IPC routing status: Switch>...
Page 588 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ipc This example shows how to display the contents of the IPC retransmission queue: Switch> show ipc queue There are 0 IPC messages waiting for acknowledgement in the transmit queue. There are 0 IPC messages waiting for a response.
Page 589 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ipc Service Usage Total via Unreliable Connection-Less Service 12783 Total via Unreliable Sequenced Connection-Less Svc Total via Reliable Connection-Oriented Service <output truncated> Related Commands Command Description clear ipc Clears the IPC multicast routing statistics.
Page 590: Show Ipv6 Access-List
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ipv6 access-list show ipv6 access-list Use the show ipv6 access-list user EXEC command to display the contents of all current IPv6 access lists. show ipv6 access-list [access-list-name] Note This command is supported only if you have configured a dual IPv4 and IPv6 Switch Database Management (SDM) template on the switch.
Page 591 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ipv6 access-list Table 2-29 show ipv6 access-list Field Descriptions (continued) Field Description An equal operand that compares the source or destination ports of TCP or UDP packets. bgp (matches) Border Gateway Protocol.
Page 592: Show Ipv6 Dhcp Conflict
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ipv6 dhcp conflict show ipv6 dhcp conflict Use the show ipv6 dhcp conflict privileged EXEC commandto display address conflicts found by a Dynamic Host Configuration Protocol for IPv6 (DHCPv6) server when addresses are offered to the client.
Page 593: Show Ipv6 Mld Snooping
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ipv6 mld snooping show ipv6 mld snooping Use the show ipv6 mld snooping user EXEC command to display IP version 6 (IPv6) Multicast Listener Discovery (MLD) snooping configuration of the switch or the VLAN. show ipv6 mld snooping [vlan vlan-id] [ | {begin | exclude | include} expression] Note This command is supported only if you have configured a dual IPv4 and IPv6 Switch Database...
Page 594 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ipv6 mld snooping Vlan 100: -------- MLD snooping : Disabled MLDv1 immediate leave : Disabled Explicit host tracking : Enabled Multicast router learning mode : pim-dvmrp Robustness variable Last listener query count Last listener query interval : 1000...
Page 595: Show Ipv6 Mld Snooping Address
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ipv6 mld snooping address show ipv6 mld snooping address Use the show ipv6 mld snooping address user EXEC command to display all or specified IP Version 6 (IPv6) multicast address information maintained by Multicast Listener Discovery (MLD) snooping.
Page 596 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ipv6 mld snooping address Examples This is an example of output from the show snooping address user EXEC command: Switch> show ipv6 mld snooping address Vlan Group Type Version Port List ------------------------------------------------------------- FF12::3 user...
Page 597: Show Ipv6 Mld Snooping Mrouter
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ipv6 mld snooping mrouter show ipv6 mld snooping mrouter Use the show ipv6 mld snooping mrouter user EXEC command to display dynamically learned and manually configured IP version 6 (IPv6) Multicast Listener Discovery (MLD) router ports for the switch or a VLAN.
Page 598 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ipv6 mld snooping mrouter This is an example of output from the show ipv6 mld snooping mrouter vlan command. It shows multicast router ports for a specific VLAN. Switch>...
Page 599: Show Ipv6 Mld Snooping Querier
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ipv6 mld snooping querier show ipv6 mld snooping querier Use the show ipv6 mld snooping querier user EXEC command to display IP version 6 (IPv6) Multicast Listener Discovery (MLD) snooping querier-related information most recently received by the switch or the VLAN.
Page 600 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ipv6 mld snooping querier Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output do not appear, but the lines that contain Output appear. Examples This is an example of output from the show ipv6 mld snooping querier command: Switch>...
Page 601: Show Ipv6 Route Updated
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ipv6 route updated show ipv6 route updated Use the show ipv6 route updated command in user EXEC command to display the current contents of the IPv6 routing table. show ipv6 route [protocol] updated [boot-up] {hh:mm | day{month [hh:mm]} [{hh:mm | day{month [hh:mm]}] [ | {begin | exclude | include} expression] Syntax Description...
Page 602 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show ipv6 route updated Usage Guidelines Use the show ipv6 route privileged EXEC command to display the current contents of the IPv6 routing table. Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output do not appear, but the lines that contain Output appear.
Page 603: Show L2Protocol-Tunnel
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show l2protocol-tunnel show l2protocol-tunnel Use the show l2protocol-tunnel user EXEC command to display information about Layer 2 protocol tunnel ports. Displays information for interfaces with protocol tunneling enabled. show l2protocol-tunnel [interface interface-id] [summary] [ | {begin | exclude | include} expression] Syntax Description...
Page 604 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show l2protocol-tunnel Examples This is an example of output from the show l2protocol-tunnel command: Switch> show l2protocol-tunnel COS for Encapsulated Packets: 5 Drop Threshold for Encapsulated Packets: 0 Port Protocol Shutdown Drop...
Page 605 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show l2protocol-tunnel Related Commands Command Description clear l2protocol-tunnel counters Clears counters for protocol tunneling ports. l2protocol-tunnel Enables Layer 2 protocol tunneling for CDP, STP, or VTP packets on an interface. l2protocol-tunnel cos Configures a class of service (CoS) value for tunneled Layer 2 protocol packets.
Page 606: Show Lacp
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show lacp show lacp Use the show lacp user EXEC command to display Link Aggregation Control Protocol (LACP) channel-group information. show lacp [channel-group-number] {counters | internal | neighbor | sys-id} [ | {begin | exclude | include} expression] Syntax Description channel-group-number...
Page 607 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show lacp Table 2-30 describes the fields in the display. Table 2-30 show lacp counters Field Descriptions Field Description LACPDUs Sent and Recv The number of LACP packets sent and received by a port. Marker Sent and Recv The number of LACP marker packets sent and received by a port.
Page 608 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show lacp Table 2-31 show lacp internal Field Descriptions (continued) Field Description Admin Key Administrative key assigned to this port. LACP automatically generates an administrative key value as a hexadecimal number. The administrative key defines the ability of a port to aggregate with other ports.
Page 609 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show lacp This is an example of output from the show lacp sys-id command: Switch> show lacp sys-id 32765,0002.4b29.3a00 The system identification is made up of the system priority and the system MAC address. The first two bytes are the system priority, and the last six bytes are the globally administered individual MAC address associated to the system.
Page 610: Show Link State Group
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show link state group show link state group Use the show link state group privileged EXEC command to display the link-state group information. show link state group [number] [detail] [ | {begin | exclude | include} expression] Syntax Description number (Optional) Number of the link-state group.
Page 611 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show link state group This is an example of output from the show link state group detail command: Switch> show link state group detail (Up):Interface up (Dwn):Interface Down (Dis):Interface disabled Link State Group: 1 Status: Enabled, Down Upstream Interfaces : Gi1/0/17(Dwn) Gi1/0/18(Dwn)
Page 612: Show Location
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show location show location Use the show location user EXEC command to display location information for an endpoint. show location admin-tag | [ | {begin | exclude | include} expression] show location civic-location {identifier id number | interface interface-id | static } | {begin | exclude | include} expression] show location elin-location {identifier id number | interface interface-id | static } | {begin |...
Page 613 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show location Examples This is an example of output from the show location civic-location command that displays location information for an interface: Switch> show location civic interface gigabitethernet2/0/1 Civic location information -------------------------- Identifier...
Page 614 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show location This is an example of output from the show location elin static command that displays all emergency location information: Switch> show location elin static Elin location information -------------------------- Identifier : 1 Elin...
Page 615: Show Logging
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show logging show logging Use the show logging privileged EXEC command to display the on-board failure logging (OBFL) information. show logging onboard [module [switch-number]] {{clilog | environment | message | temperature | uptime | voltage} [continuous | detail | summary] [start hh:mm:ss day month year] [end hh:mm:ss day month year]} [ | {begin | exclude | include} expression] Syntax Description...
Page 616 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show logging | include (Optional) Display includes lines that match the specified expression. expression Expression in the output to use as a reference point. Though visible in the command-line help strings, the poe keyword is not supported. Note Defaults There is no default.
Page 617 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show logging Examples This is an example of output from the show logging onboard clilog continuous command: Switch# show logging onboard clilog continuous -------------------------------------------------------------------------------- CLI LOGGING CONTINUOUS INFORMATION -------------------------------------------------------------------------------- MM/DD/YYYY HH:MM:SS COMMAND --------------------------------------------------------------------------------...
Page 618 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show logging Application name voltage : Path : obfl0: CLI enable status : enabled Platform enable status: enabled This is an example of output from the show logging onboard temperature continuous command: Switch# show logging onboard temperature continuous -------------------------------------------------------------------------------- TEMPERATURE CONTINUOUS INFORMATION...
Page 619 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show logging This is an example of output from the show logging onboard voltage summary command: Switch# show logging onboard voltage summary -------------------------------------------------------------------------------- VOLTAGE SUMMARY INFORMATION -------------------------------------------------------------------------------- Number of sensors Sampling frequency : 60 seconds Maximum time of storage...
Page 620: Show Mac Access-Group
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac access-group show mac access-group Use the show mac access-group user EXEC command to display the MAC access control lists (ACLs) configured for an interface or a switch. show mac access-group [interface interface-id] [ | {begin | exclude | include} expression] Syntax Description interface interface-id...
Page 621 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac access-group Related Commands Command Description mac access-group Applies a MAC access group to an interface. Cisco Catalyst Blade Switch 3120 for HP Command Reference 2-591 OL-12248-03...
Page 622: Show Mac Address-Table
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac address-table show mac address-table Use the show mac address-table user EXEC command to display a specific MAC address table static and dynamic entry or the MAC address table static and dynamic entries on a specific interface or VLAN. show mac address-table [ | {begin | exclude | include} expression] Syntax Description | begin...
Page 623 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac address-table Related Commands Command Description clear mac address-table dynamic Deletes from the MAC address table a specific dynamic address, all dynamic addresses on a particular interface, or all dynamic addresses on a particular VLAN.
Page 624: Show Mac Address-Table Address
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac address-table address show mac address-table address Use the show mac address-table address user EXEC command to display MAC address table information for the specified MAC address. show mac address-table address mac-address [interface interface-id] [vlan vlan-id] [ | {begin | exclude | include} expression] Syntax Description...
Page 625 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac address-table address Related Commands Command Description show mac address-table aging-time Displays the aging time in all VLANs or the specified VLAN. show mac address-table count Displays the number of addresses present in all VLANs or the specified VLAN.
Page 626: Show Mac Address-Table Aging-Time
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac address-table aging-time show mac address-table aging-time Use the show mac address-table aging-time user EXEC command to display the aging time of a specific address table instance, all address table instances on a specified VLAN or, if a specific VLAN is not specified, on all VLANs.
Page 627 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac address-table aging-time Related Commands Command Description mac address-table aging-time Sets the length of time that a dynamic entry remains in the MAC address table after the entry is used or updated. show mac address-table address Displays MAC address table information for the specified MAC address.
Page 628: Show Mac Address-Table Count
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac address-table count show mac address-table count Use the show mac address-table count user EXEC command to display the number of addresses present in all VLANs or the specified VLAN. show mac address-table count [vlan vlan-id] [ | {begin | exclude | include} expression] Syntax Description vlan vlan-id...
Page 629 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac address-table count Related Commands Command Description show mac address-table address Displays MAC address table information for the specified MAC address. show mac address-table aging-time Displays the aging time in all VLANs or the specified VLAN. show mac address-table dynamic Displays dynamic MAC address table entries only.
Page 630: Show Mac Address-Table Dynamic
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac address-table dynamic show mac address-table dynamic Use the show mac address-table dynamic user EXEC command to display only dynamic MAC address table entries. show mac address-table dynamic [address mac-address] [interface interface-id] [vlan vlan-id] [ | {begin | exclude | include} expression] Syntax Description address mac-address...
Page 631 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac address-table dynamic Related Commands Command Description clear mac address-table dynamic Deletes from the MAC address table a specific dynamic address, all dynamic addresses on a particular interface, or all dynamic addresses on a particular VLAN.
Page 632: Show Mac Address-Table Interface
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac address-table interface show mac address-table interface Use the show mac address-table interface user command to display the MAC address table information for the specified interface in the specified VLAN. show mac address-table interface interface-id [vlan vlan-id] [ | {begin | exclude | include} expression] Syntax Description...
Page 633 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac address-table interface Related Commands Command Description show mac address-table address Displays MAC address table information for the specified MAC address. show mac address-table aging-time Displays the aging time in all VLANs or the specified VLAN.
Page 634: Show Mac Address-Table Learning
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac address-table learning show mac address-table learning Use the show mac address-table learning user EXEC command to display the status of MAC address learning for all VLANs or the specified VLAN. show mac address-table learning [vlan vlan-id] [ | {begin | exclude | include} expression] Syntax Description vlan vlan-id...
Page 635: Show Mac Address-Table Move Update
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac address-table move update show mac address-table move update Use the show mac address-table move update user EXEC command to display the MAC address-table move update information on the switch. show mac address-table move update [ | {begin | exclude | include} expression] Syntax Description | begin...
Page 636 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac address-table move update Related Commands Command Description clear mac address-table move Clears the MAC address-table move update counters. update mac address-table move update Configures MAC address-table move update on the switch. {receive | transmit} Cisco Catalyst Blade Switch 3120 for HP Command Reference 2-606...
Page 637: Show Mac Address-Table Notification
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac address-table notification show mac address-table notification Use the show mac address-table notification user EXEC command to display the MAC address notification settings for all interfaces or the specified interface. show mac address-table notification [interface [interface-id]] [ | {begin | exclude | include} expression] Syntax Description...
Page 638 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac address-table notification Examples This is an example of output from the show mac address-table notification command: Switch> show mac address-table notification MAC Notification Feature is Enabled on the switch Interval between Notification Traps : 60 secs Number of MAC Addresses Added : 4 Number of MAC Addresses Removed : 4...
Page 639: Show Mac Address-Table Static
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac address-table static show mac address-table static Use the show mac address-table static user EXEC command to display only static MAC address table entries. show mac address-table static [address mac-address] [interface interface-id] [vlan vlan-id] [ | {begin | exclude | include} expression] Syntax Description address mac-address...
Page 640 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac address-table static Related Commands Command Description mac address-table static Adds static addresses to the MAC address table. mac address-table static drop Enables unicast MAC address filtering and configures the switch to drop traffic with a specific source or destination MAC address.
Page 641: Show Mac Address-Table Vlan
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac address-table vlan show mac address-table vlan Use the show mac address-table vlan user EXEC command to display the MAC address table information for the specified VLAN. show mac address-table vlan vlan-id [ | {begin | exclude | include} expression] Syntax Description vlan-id...
Page 642 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mac address-table vlan Related Commands Command Description show mac address-table address Displays MAC address table information for the specified MAC address. show mac address-table aging-time Displays the aging time in all VLANs or the specified VLAN.
Page 643: Show Mls Qos
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mls qos show mls qos Use the show mls qos user EXEC command to display global quality of service (QoS) configuration information. show mls qos [ | {begin | exclude | include} expression] Syntax Description | begin (Optional) Display begins with the line that matches the expression.
Page 644: Show Mls Qos Aggregate-Policer
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mls qos aggregate-policer show mls qos aggregate-policer Use the show mls qos aggregate-policer user EXEC command to display the quality of service (QoS) aggregate policer configuration. A policer defines a maximum permissible rate of transmission, a maximum burst size for transmissions, and an action to take if either maximum is exceeded.
Page 645: Show Mls Qos Input-Queue
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mls qos input-queue show mls qos input-queue Use the show mls qos input-queue user EXEC command to display quality of service (QoS) settings for the ingress queues. show mls qos input-queue [ | {begin | exclude | include} expression] Syntax Description | begin...
Page 646 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mls qos input-queue Related Commands Command Description mls qos srr-queue input bandwidth Assigns shaped round robin (SRR) weights to an ingress queue. mls qos srr-queue input buffers Allocates the buffers between the ingress queues.
Page 647: Show Mls Qos Interface
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mls qos interface show mls qos interface Use the show mls qos interface user EXEC command to display quality of service (QoS) information at the port level. show mls qos interface [interface-id] [buffers | queueing | statistics] [ | {begin | exclude | include} expression] Syntax Description...
Page 648 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mls qos interface Examples This is an example of output from the show mls qos interface interface-id command when VLAN-based QoS is enabled: Switch> show mls qos interface gigabitethernet1/0/1 GigabitEthernet1/0/1 trust state:not trusted trust mode:not trusted...
Page 649 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mls qos interface 45 - 49 : 50 - 54 : 55 - 59 : 60 - 64 : dscp: outgoing ------------------------------- 363949 10 - 14 : 15 - 19 : 20 - 24 : 25 - 29 :...
Page 650 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mls qos interface Related Commands Command Description mls qos queue-set output buffers Allocates buffers to a queue-set. mls qos queue-set output threshold Configures the weighted tail-drop (WTD) thresholds, guarantees the availability of buffers, and configures the maximum memory allocation to a queue-set.
Page 651: Show Mls Qos Maps
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mls qos maps show mls qos maps Use the show mls qos maps user EXEC command to display quality of service (QoS) mapping information. During classification, QoS uses the mapping tables to represent the priority of the traffic and to derive a corresponding class of service (CoS) or Differentiated Services Code Point (DSCP) value from the received CoS, DSCP, or IP precedence value.
Page 652 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mls qos maps The DSCP input queue threshold and the DSCP output queue threshold maps appear as a matrix. The d1 column specifies the most-significant digit of the DSCP number. The d2 row specifies the least-significant digit in the DSCP number.
Page 653 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mls qos maps Dscp-inputq-threshold map: d1 :d2 -------------------------------------------------------------------- 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 01-01 02-01 02-01 02-01 02-01 02-01 02-01 02-01 02-01 01-01 01-01...
Page 654: Show Mls Qos Queue-Set
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mls qos queue-set show mls qos queue-set Use the show mls qos queue-set user EXEC command to display quality of service (QoS) settings for the egress queues. show mls qos queue-set [qset-id] [ | {begin | exclude | include} expression] Syntax Description qset-id...
Page 655 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mls qos queue-set Related Commands Command Description mls qos queue-set output buffers Allocates buffers to the queue-set. mls qos queue-set output threshold Configures the weighted tail-drop (WTD) thresholds, guarantees the availability of buffers, and configures the maximum memory allocation of the queue-set.
Page 656: Show Mls Qos Vlan
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mls qos vlan show mls qos vlan Use the show mls qos vlan user EXEC command to display the policy maps attached to a switch virtual interface (SVI). show mls qos vlan vlan-id [ | {begin | exclude | include} expression] Syntax Description vlan-id...
Page 657: Show Monitor
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show monitor show monitor Use the show monitor user EXEC command to display information about all Switched Port Analyzer (SPAN) and Remote SPAN (RSPAN) sessions on the switch. Use the command with keywords to show a specific session, all sessions, all local sessions, or all remote sessions.
Page 658 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show monitor Examples This is an example of output for the show monitor user EXEC command: Switch# show monitor Session 1 --------- Type : Local Session Source Ports : RX Only : Gi4/0/1 Both : Gi4/0/2-3,Gi4/0/5-6 Destination Ports : Gi4/0/10...
Page 659 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show monitor Related Commands Command Description monitor session Starts or modifies a SPAN or RSPAN session. Cisco Catalyst Blade Switch 3120 for HP Command Reference 2-629 OL-12248-03...
Page 660: Show Mvr
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mvr show mvr Use the show mvr privileged EXEC command without keywords to display the current Multicast VLAN Registration (MVR) global parameter values, including whether or not MVR is enabled, the MVR multicast VLAN, the maximum query response time, the number of multicast groups, and the MVR mode (dynamic or compatible).
Page 661: Show Mvr Members
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mvr Related Commands Command Description mvr (global configuration) Enables and configures multicast VLAN registration on the switch. mvr (interface configuration) Configures MVR ports. show mvr interface Displays the configured MVR interfaces, status of the specified interface, or all multicast groups to which the interface belongs when the interface and members keywords are appended to the command.
Page 662: Show Mvr Interface
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mvr interface show mvr interface Use the show mvr interface privileged EXEC command without keywords to display the Multicast VLAN Registration (MVR) receiver and source ports. Use the command with keywords to display MVR parameters for a specific receiver port.
Page 663 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mvr interface In the preceding display, Status is defined as follows: Active means the port is part of a VLAN. • Up/Down means that the port is forwarding/nonforwarding. •...
Page 664: Show Mvr Members
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mvr members show mvr members Use the show mvr members privileged EXEC command to display all receiver and source ports that are currently members of an IP multicast group. show mvr members [ip-address] [ | {begin | exclude | include} expression] Syntax Description ip-address...
Page 665 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show mvr members This is an example of output from the show mvr members ip-address command. It displays the members of the IP multicast group with that address: Switch# show mvr members 239.255.0.2 239.255.003.--22 ACTIVE...
Page 666: Show Network-Policy Profile
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show network-policy profile show network-policy profile Use the show network policy profile privileged EXEC command to display the network-policy profiles. show network-policy profile [profile number] [detail] [ | {begin | exclude | include} expression] Syntax Description profile (Optional) Display the network-policy profile number.
Page 667 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show network-policy profile Related Commands Command Description network-policy Applies a network-policy to an interface. network-policy profile (global Creates the network-policy profile. configuration) network-policy profile Configures the attributes of network-policy profiles. (network-policy configuration) Cisco Catalyst Blade Switch 3120 for HP Command Reference 2-637...
Page 668: Show Nmsp
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show nmsp show nmsp Use the show nmsp privileged EXEC command to display the Network Mobility Services Protocol (NMSP) information for the switch. This command is available only when your switch is running the cryptographic (encrypted) software image.
Page 669 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show nmsp This is an example of output from the show nmsp capability command: Switch# show nmsp capability NMSP Switch Capability ------------------------------ Service Subservice ----------- -------------- Attachment Wired Station Location Subscription This is an example of output from the show nmsp notification interval command:...
Page 670 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show nmsp This is an example of output from the show nmsp show subscription detail and the show nmsp show subscription summary commands: Switch# show nmsp subscription detail Mobility Services Subscribed by 172.19.35.109: Services Subservices...
Page 671: Show Pagp
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show pagp show pagp Use the show pagp user EXEC command to display Port Aggregation Protocol (PAgP) channel-group information. show pagp [channel-group-number] {counters | dual-active | internal | neighbor} [ | {begin | exclude | include} expression]] Syntax Description channel-group-number...
Page 672 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show pagp This is an example of output from the show pagp 1 internal command: Switch> show pagp 1 internal Flags: S - Device is sending Slow hello. C - Device is in Consistent state.
Page 673: Show Parser Macro
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show parser macro show parser macro Use the show parser macro user EXEC command to display the parameters for all configured macros or for one macro on the switch. show parser macro [{brief | description [interface interface-id] | name macro-name}] [ | {begin | exclude | include} expression] Syntax Description...
Page 674 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show parser macro # Recommended value for access vlan (AVID) should not be 1 switchport access vlan $AVID switchport mode access <output truncated> -------------------------------------------------------------- Macro name : cisco-phone Macro type : default interface # Cisco IP phone + desktop template # macro keywords $AVID $VVID...
Page 675 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show parser macro This is an example of output from the show parser macro name command: Switch# show parser macro name standard-switch10 Macro name : standard-switch10 Macro type : customizable macro description standard-switch10 # Trust QoS settings on VOIP packets auto qos voip trust...
Page 676: Show Policy-Map
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show policy-map show policy-map Use the show policy-map user EXEC command to display quality of service (QoS) policy maps, which define classification criteria for incoming traffic. Policy maps can include policers that specify the bandwidth limitations and the action to take if the limits are exceeded.
Page 677 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show policy-map Related Commands Command Description policy-map Creates or modifies a policy map that can be attached to multiple ports to specify a service policy. Cisco Catalyst Blade Switch 3120 for HP Command Reference 2-647 OL-12248-03...
Page 678: Show Port-Security
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show port-security show port-security Use the show port-security privileged EXEC command to display port-security settings for an interface or for the switch. show port-security [interface interface-id] [address | vlan] [ | {begin | exclude | include} expression] Syntax Description interface interface-id...
Page 679 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show port-security Examples This is an example of the output from the show port-security command: Switch# show port-security Secure Port MaxSecureAddr CurrentAddr SecurityViolation Security Action (Count) (Count) (Count) ------------------------------------------------------------------------------- Gi1/0/1 Shutdown...
Page 680 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show port-security Related Commands Command Description clear port-security Deletes from the MAC address table a specific type of secure address or all the secure addresses on the switch or an interface. switchport port-security Enables port security on a port, restricts the use of the port to a user-defined group of stations, and configures secure MAC...
Page 681: Show Sdm Prefer
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show sdm prefer show sdm prefer Use the show sdm prefer privileged EXEC command to display information about the Switch Database Management (SDM) templates that can be used to maximize used for allocating system resources for a particular feature, or use the command without a keyword to display the template in use.
Page 682 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show sdm prefer Examples This is an example of output from the show sdm prefer command, which displays the template in use: Switch# show sdm prefer "default" template: The selected template optimizes the resources in the switch to support this level of features for 8 routed interfaces and 1024 VLANs.
Page 683 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show sdm prefer This is an example of output from the show sdm prefer dual-ipv4-and-ipv6 vlan command: Switch# show sdm prefer dual-ipv4-and-ipv6 vlan The current template is "desktop IPv4 and IPv6 vlan" template. The selected template optimizes the resources in the switch to support this level of features for 8 routed interfaces and 1024 VLANs.
Page 684 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show sdm prefer Related Commands Command Description sdm prefer Sets the SDM template to maximize resources for routing or VLANs or to the default template, to select a dual IPv4 and IPv6 template, or to select the desktop templates.
Page 685: Show Setup Express
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show setup express show setup express Use the show setup express privileged EXEC command to display if Express Setup mode is active on the switch. show setup express [ | {begin | exclude | include} expression] Syntax Description | begin (Optional) Display begins with the line that matches the expression.
Page 686: Show Spanning-Tree
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show spanning-tree show spanning-tree Use the show spanning-tree user EXEC command to display spanning-tree state information. show spanning-tree [bridge-group | active [detail] | backbonefast | blockedports | bridge | detail [active] | inconsistentports | interface interface-id | mst | pathcost method | root | summary [totals] | uplinkfast | vlan vlan-id] [ | {begin | exclude | include} expression] show spanning-tree bridge-group [active [detail] | blockedports | bridge | detail [active] |...
Page 687 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show spanning-tree mst [configuration (Optional) Display the multiple spanning-tree (MST) region [digest]] [instance-id configuration and status (available only in privileged EXEC mode). [detail | interface The keywords have these meanings: interface-id [detail]] digest—(Optional) Display the MD5 digest included in the current •...
Page 688 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show spanning-tree | begin (Optional) Display begins with the line that matches the expression. | exclude (Optional) Display excludes lines that match the expression. | include (Optional) Display includes lines that match the specified expression. expression Expression in the output to use as a reference point.
Page 689 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show spanning-tree Port 1 (GigabitEthernet2/0/1) of VLAN0001 is forwarding Port path cost 3019, Port priority 128, Port Identifier 128.24. Designated root has priority 32768, address 0001.42e2.cdd0 Designated bridge has priority 32768, address 00d0.bbf5.c680 Designated port id is 128.25, designated path cost 19 Timers: message age 2, forward delay 0, hold 0 Number of transitions to forwarding state: 1...
Page 690 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show spanning-tree This is an example of output from the show spanning-tree mst configuration command: Switch# show spanning-tree mst configuration Name [region1] Revision Instance Vlans Mapped -------- ------------------ 1-9,21-4094 10-20 ----------------------------...
Page 691 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show spanning-tree Related Commands Command Description clear spanning-tree counters Clears the spanning-tree counters. clear spanning-tree detected-protocols Restarts the protocol migration process. spanning-tree backbonefast Enables the BackboneFast feature. spanning-tree bpdufilter Prevents an interface from sending or receiving bridge protocol data units (BPDUs).
Page 692: Show Storm-Control
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show storm-control show storm-control Use the show storm-control user EXEC command to display broadcast, multicast, or unicast storm control settings on the switch or on the specified interface or to display storm-control history. show storm-control [interface-id] [broadcast | multicast | unicast] [ | {begin | exclude | include} expression] Syntax Description...
Page 693 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show storm-control This is an example of output from the show storm-control command for a specified interface. Because no traffic-type keyword was entered, the broadcast storm control settings appear. Switch>...
Page 694: Show Switch
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show switch show switch Use the show switch user EXEC command to display information related to the stack member or the switch stack. show switch [stack-member-number | chassis-mgmt | detail | neighbors | stack-ports [summary] | stack-ring activity [detail]] [ | {begin | exclude | include} expression] Syntax Description stack-member-number...
Page 695 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show switch Initializing—A switch has determined whether its stack master status. If it is not the stack master, • it is receiving its system- and interface-level configuration from the stack master and loading it. •...
Page 696 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show switch This example shows detailed stack information: Switch> show switch detail Switch/Stack Mac Address : 0013.c4db.7e00 Mac persistency wait time: 4 mins Current Switch# Role Mac Address Priority Version State ----------------------------------------------------------...
Page 697 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show switch Table 2-34 show switch stack-ports summary Command Output Field Description Switch#/Port# Member number and its stack port number. Stack Port Status Absent—No cable is detected on the stack •...
Page 698 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show switch This example shows detailed stack-ring activity information: Switch> show switch stack-ring activity detail Switch Asic Rx Queue-1 Rx Queue-2 Rx Queue-3 Rx Queue-4 Total ------------------------------------------------------------------------- 2021864 1228937 281510 3532311...
Page 699: Show System Mtu
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show system mtu show system mtu Use the show system mtu privileged EXEC command to display the global maximum transmission unit (MTU) or maximum packet size set for the switch. show system mtu [ | {begin | exclude | include} expression] Syntax Description | begin...
Page 700: Show Udld
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show udld show udld Use the show udld user EXEC command to display UniDirectional Link Detection (UDLD) administrative and operational status for all ports or the specified port. show udld [interface-id] [ | {begin | exclude | include} expression] Syntax Description interface-id...
Page 701 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show udld Table 2-35 describes the fields in this display. Table 2-35 show udld Field Descriptions Field Description Interface The interface on the local device configured for UDLD. Port enable administrative How UDLD is configured on the port.
Page 702 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show udld Related Commands Command Description udld Enables aggressive or normal mode in UDLD or sets the configurable message timer time. udld port Enables UDLD on an individual interface or prevents a fiber-optic interface from being enabled by the udld global configuration command.
Page 703: Show Version
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show version show version Use the show version user EXEC command to display version information for the hardware and firmware and software license information. show version [ | {begin | exclude | include} expression] Syntax Description | begin (Optional) Display begins with the line that matches the expression.
Page 704 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show version Last reset from power-on Target IOS Version 12.2(40)EX2 1 Virtual Ethernet interface 1 FastEthernet interface 52 Gigabit Ethernet interfaces 4 Ten Gigabit Ethernet interfaces The password-recovery mechanism is enabled. 512K bytes of flash-simulated non-volatile configuration memory.
Page 705: Show Vlan
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show vlan show vlan Use the show vlan user EXEC command to display the parameters for all configured VLANs or one VLAN (if the VLAN ID or name is specified) on the switch. show vlan [brief | dot1q tag native | id vlan-id | internal usage | mtu | name vlan-name | private-vlan [type] | remote-span | summary] [ | {begin | exclude | include} expression] Syntax Description...
Page 706 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show vlan Usage Guidelines In the show vlan mtu command output, the MTU_Mismatch column shows whether all the ports in the VLAN have the same MTU. When yes appears in this column, it means that the VLAN has ports with different MTUs, and packets that are switched from a port with a larger MTU to a port with a smaller MTU might be dropped.
Page 707 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show vlan Primary Secondary Type Ports ------ --------- ----------------- ------------------------------------------ Primary Secondary Type Ports ------- --------- ----------------- ------------------------------------------ isolated Gi1/0/1,Gi3/0/1 community Gi1/0/1, Gi3/0/1 community Gi1/0/1, Gi3/0/1 <output truncated> Table 2-36 show vlan Command Output Fields Field...
Page 708 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show vlan community Gi1/0/13, Gi1/0/1, Gi2/0/13, Gi3/0/14, Gi3/0/1 non-operational 2000 2500 isolated Gi1/0/5, Gi1/0/10, Gi2/0/5, Gi2/0/10 This is an example of output from the show vlan private-vlan type command: Switch>...
Page 709 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show vlan Related Commands Command Description private-vlan Configures a VLAN as a community, isolated, or primary VLAN or associates a primary VLAN with secondary VLANs. switchport mode Configures the VLAN membership mode of a port. vlan (global Enables VLAN configuration mode where you can configure VLANs 1 to configuration)
Page 710: Show Vlan Access-Map
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show vlan access-map show vlan access-map Use the show vlan access-map privileged EXEC command to display information about a particular VLAN access map or for all VLAN access maps. show vlan access-map [mapname] [ | {begin | exclude | include} expression] Syntax Description mapname...
Page 711: Show Vlan Filter
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show vlan filter show vlan filter Use the show vlan filter privileged EXEC command to display information about all VLAN filters or about a particular VLAN or VLAN access map. show vlan filter [access-map name | vlan vlan-id] [ | {begin | exclude | include} expression] Syntax Description access-map name...
Page 712: Show Vmps
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show vmps show vmps Use the show vmps user EXEC command without keywords to display the VLAN Query Protocol (VQP) version, reconfirmation interval, retry count, VLAN Membership Policy Server (VMPS) IP addresses, and the current and primary servers, or use the statistics keyword to display client-side statistics.
Page 713 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show vmps Wrong Version: Insufficient Resource: 0 Table 2-37 show vmps statistics Field Descriptions Field Description VQP Queries Number of queries sent by the client to the VMPS. VQP Responses Number of responses sent to the client from the VMPS.
Page 714: Show Vtp
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show vtp show vtp Use the show vtp user EXEC command to display general information about the VLAN Trunking Protocol (VTP) management domain, status, and counters. show vtp {counters | password | status} [ | {begin | exclude | include} expression] Syntax Description counters Display the VTP statistics for the switch.
Page 715 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show vtp Table 2-38 describes each field in the display. Table 2-38 show vtp counters Field Descriptions Field Description Summary advertisements Number of summary advertisements received by this switch on its trunk received ports.
Page 716 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show vtp Table 2-38 show vtp counters Field Descriptions (continued) Field Description Number of V1 summary Number of Version 1 errors. errors Version 1 summary errors increment whenever a switch in VTP V2 mode receives a VTP Version 1 frame.
Page 717 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show vtp Table 2-39 show vtp status Field Descriptions (continued) Field Description VTP Operating Mode Displays the VTP operating mode, which can be server, client, or transparent. Server: a switch in VTP server mode is enabled for VTP and sends advertisements.
Page 718 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands show vtp Cisco Catalyst Blade Switch 3120 for HP Command Reference 2-688 OL-12248-03...
Page 719: Shutdown
2 V ] Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands shutdown shutdown Use the shutdown interface configuration command on the switch stack or on a standalone switch to disable an interface. Use the no form of this command to restart a disabled interface. shutdown no shutdown Syntax Description...
Page 720: Shutdown Vlan
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands shutdown vlan shutdown vlan Use the shutdown vlan global configuration command on the switch stack or on a standalone switch to shut down (suspend) local traffic on the specified VLAN. Use the no form of this command to restart local traffic on the VLAN.
Page 721: Small-Frame Violation Rate
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands small-frame violation rate small-frame violation rate Use the small-frame violation rate pps interface configuration command on the switch stack or on a standalone switch to configure the rate (threshold) for an interface to be error disabled when it receives VLAN-tagged packets that are small frames (67 bytes or less) at the specified rate.
Page 722 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands small-frame violation rate Related Commands Command Description errdisable detect cause small-frame Allows any switch port to be put into the error-disabled state if an incoming frame is smaller than the minimum size and arrives at the specified rate (threshold).
Page 723: Snmp-Server Enable Traps
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands snmp-server enable traps snmp-server enable traps Use the snmp-server enable traps global configuration command on the switch stack or on a standalone switch to enable the switch to send Simple Network Management Protocol (SNMP) notifications for various traps or inform requests to the network management system (NMS).
Page 724 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands snmp-server enable traps dot1x [auth-fail-vlan | (Optional) Enable IEEE 802.1x traps. The keywords have these meanings: guest-vlan | auth-fail-vlan—(Optional) Generate a trap when the port moves to the •...
Page 725 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands snmp-server enable traps (Optional) Enable Protocol-Independent Multicast (PIM) traps. The [invalid-pim-message | keywords have these meanings: neighbor-change | invalid-pim-message—(Optional) Enable invalid PIM message traps. • rp-mapping-change] neighbor-change—(Optional) Enable PIM neighbor-change traps. •...
Page 726 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands snmp-server enable traps Defaults The sending of SNMP traps is disabled. Command Modes Global configuration Command History Release Modification 12.2(40)EX1 This command was introduced. 12.2(46)SE The dot1x [ auth-fail-vlan | guest-vlan | no-auth-fail-vlan | no-guest-vlan ] keywords were added.
Page 727: Snmp-Server Host
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands snmp-server host snmp-server host Use the snmp-server host global configuration command on the switch stack or on a standalone switch to specify the recipient (host) of a Simple Network Management Protocol (SNMP) notification operation. Use the no form of this command to remove the specified host.
Page 728 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands snmp-server host community-string Password-like community string sent with the notification operation. Though you can set this string by using the snmp-server host command, we recommend that you define this string by using the snmp-server community global configuration command before using the snmp-server host command.
Page 729 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands snmp-server host Though visible in the command-line help strings, the ru-ctrl keyword is not supported on Note nonstacking-capable switches. Defaults This command is disabled by default. No notifications are sent. If you enter this command with no keywords, the default is to send all trap types to the host.
Page 730 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands snmp-server host the snmp-server host command for that host must be enabled. Some notification types cannot be controlled with the snmp-server enable traps command. For example, some notification types are always enabled.
Page 731: Snmp Trap Mac-Notification
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands snmp trap mac-notification snmp trap mac-notification Use the snmp trap mac-notification interface configuration command on the switch stack or on a standalone switch to enable the Simple Network Management Protocol (SNMP) MAC address notification trap on a specific Layer 2 interface.
Page 732 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands snmp trap mac-notification Related Commands Command Description clear mac address-table notification Clears the MAC address notification global counters. mac address-table notification Enables the MAC address notification feature. show mac address-table notification Displays the MAC address notification settings for all interfaces or on the specified interface when the interface keyword is appended.
Page 733: Spanning-Tree Backbonefast
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree backbonefast spanning-tree backbonefast Use the spanning-tree backbonefast global configuration command on the switch stack or on a standalone switch to enable the BackboneFast feature. Use the no form of the command to return to the default setting.
Page 734: Spanning-Tree Bpdufilter
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree bpdufilter spanning-tree bpdufilter Use the spanning-tree bpdufilter interface configuration command on the switch stack or on a standalone switch to prevent an interface from sending or receiving bridge protocol data units (BPDUs). Use the no form of this command to return to the default setting.
Page 735 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree bpdufilter Related Commands Command Description show running-config Displays the operating configuration. For syntax information, use this link to the Cisco IOS Release 12.2 Command Reference listing page: http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/prod _command_reference_list.html Select the Cisco IOS Commands Master List, Release 12.2 to...
Page 736: Spanning-Tree Bpduguard
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree bpduguard spanning-tree bpduguard Use the spanning-tree bpduguard interface configuration command on the switch stack or on a standalone switch to put an interface in the error-disabled state when it receives a bridge protocol data unit (BPDU).
Page 737 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree bpduguard Related Commands Command Description show running-config Displays the operating configuration. For syntax information, use this link to the Cisco IOS Release 12.2 Command Reference listing page: http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/prod _command_reference_list.html Select the Cisco IOS Commands Master List, Release 12.2 to...
Page 738: Spanning-Tree Cost
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree cost spanning-tree cost Use the spanning-tree cost interface configuration command on the switch stack or on a standalone switch to set the path cost for spanning-tree calculations. If a loop occurs, spanning tree considers the path cost when selecting an interface to place in the forwarding state.
Page 739 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree cost Related Commands Command Description show spanning-tree interface Displays spanning-tree information for the specified interface. interface-id spanning-tree port-priority Configures an interface priority. spanning-tree vlan priority Sets the switch priority for the specified spanning-tree instance. Cisco Catalyst Blade Switch 3120 for HP Command Reference 2-709 OL-12248-03...
Page 740: Spanning-Tree Etherchannel Guard Misconfig
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree etherchannel guard misconfig spanning-tree etherchannel guard misconfig Use the spanning-tree etherchannel guard misconfig global configuration command to display an error message when the switch detects an EtherChannel misconfiguration. Use the no form of this command to disable the feature.
Page 741 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree etherchannel guard misconfig Related Commands Command Description errdisable recovery cause Enables the timer to recover from the EtherChannel channel-misconfig misconfiguration error-disabled state. show etherchannel summary Displays EtherChannel information for a channel as a one-line summary per channel-group.
Page 742: Spanning-Tree Extend System-Id
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree extend system-id spanning-tree extend system-id Use the spanning-tree extend system-id global configuration command on the switch stack or on a standalone switch to enable the extended system ID feature. spanning-tree extend system-id Note Though visible in the command-line help strings, the no version of this command is not supported.
Page 743 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree extend system-id Related Commands Command Description show spanning-tree summary Displays a summary of spanning-tree interface states. spanning-tree mst root Configures the MST root switch priority and timers based on the network diameter.
Page 744: Spanning-Tree Guard
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree guard spanning-tree guard Use the spanning-tree guard interface configuration command on the switch stack or on a standalone switch to enable root guard or loop guard on all the VLANs associated with the selected interface. Root guard restricts which interface is allowed to be the spanning-tree root port or the path-to-the root for the switch.
Page 745 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree guard ports. When the switch is operating in MST mode, BPDUs are not sent on nonboundary interfaces if the interface is blocked by loop guard in all MST instances. On a boundary interface, loop guard blocks the interface in all MST instances.
Page 746: Spanning-Tree Link-Type
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree link-type spanning-tree link-type Use the spanning-tree link-type interface configuration command on the switch stack or on a standalone switch to override the default link-type setting, which is determined by the duplex mode of the interface, and to enable rapid spanning-tree transitions to the forwarding state.
Page 747 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree link-type Related Commands Command Description clear spanning-tree detected-protocols Restarts the protocol migration process (force the renegotiation with neighboring switches) on all interfaces or on the specified interface. show spanning-tree interface Displays spanning-tree state information for the specified...
Page 748: Spanning-Tree Loopguard Default
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree loopguard default spanning-tree loopguard default Use the spanning-tree loopguard default global configuration command on the switch stack or on a standalone switch to prevent alternate or root ports from becoming designated ports because of a failure that leads to a unidirectional link.
Page 749 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree loopguard default Related Commands Command Description show running-config Displays the operating configuration. For syntax information, use this link to the Cisco IOS Release 12.2 Command Reference listing page: http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/prod_co mmand_reference_list.html Select the Cisco IOS Commands Master List, Release 12.2 to...
Page 750: Spanning-Tree Mode
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree mode spanning-tree mode Use the spanning-tree mode global configuration command on the switch stack or on a standalone switch to enable per-VLAN spanning-tree plus (PVST+), rapid PVST+, or multiple spanning tree (MST) on your switch.
Page 751 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree mode Related Commands Command Description show running-config Displays the operating configuration. For syntax information, use this link to the Cisco IOS Release 12.2 Command Reference listing page: http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/prod_comm and_reference_list.html Select the Cisco IOS Commands Master List, Release 12.2 to navigate...
Page 752: Spanning-Tree Mst Configuration
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree mst configuration spanning-tree mst configuration Use the spanning-tree mst configuration global configuration command on the switch stack or on a standalone switch to enter multiple spanning-tree (MST) configuration mode through which you configure the MST region.
Page 753 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree mst configuration When you map VLANs to an MST instance, the mapping is incremental, and VLANs specified in the command are added to or removed from the VLANs that were previously mapped. To specify a range, use a hyphen;...
Page 754: Spanning-Tree Mst Cost
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree mst cost spanning-tree mst cost Use the spanning-tree mst cost interface configuration command on the switch stack or on a standalone switch to set the path cost for multiple spanning-tree (MST) calculations. If a loop occurs, spanning tree considers the path cost when selecting an interface to put in the forwarding state.
Page 755 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree mst cost Related Commands Command Description show spanning-tree Displays MST information for the specified interface. interface interface-id spanning-tree mst Configures an interface priority. port-priority spanning-tree mst priority Configures the switch priority for the specified spanning-tree instance.
Page 756: Spanning-Tree Mst Forward-Time
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree mst forward-time spanning-tree mst forward-time Use the spanning-tree mst forward-time global configuration command on the switch stack or on a standalone switch to set the forward-delay time for all multiple spanning-tree (MST) instances. The forwarding time specifies how long each of the listening and learning states last before the interface begins forwarding.
Page 757: Spanning-Tree Mst Hello-Time
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree mst hello-time spanning-tree mst hello-time Use the spanning-tree mst hello-time global configuration command on the switch stack or on a standalone switch to set the interval between hello bridge protocol data units (BPDUs) sent by root switch configuration messages.
Page 758: Spanning-Tree Mst Max-Age
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree mst max-age spanning-tree mst max-age Use the spanning-tree mst max-age global configuration command on the switch stack or on a standalone switch to set the interval between messages that the spanning tree receives from the root switch.
Page 759: Spanning-Tree Mst Max-Hops
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree mst max-hops spanning-tree mst max-hops Use the spanning-tree mst max-hops global configuration command on the switch stack or on a standalone switch to set the number of hops in a region before the bridge protocol data unit (BPDU) is discarded and the information held for an interface is aged.
Page 760: Spanning-Tree Mst Port-Priority
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree mst port-priority spanning-tree mst port-priority Use the spanning-tree mst port-priority interface configuration command on the switch stack or on a standalone switch to configure an interface priority. If a loop occurs, the Multiple Spanning Tree Protocol (MSTP) can find the interface to put in the forwarding state.
Page 761 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree mst port-priority Related Commands Command Description show spanning-tree mst interface Displays MST information for the specified interface. interface-id spanning-tree mst cost Sets the path cost for MST calculations. spanning-tree mst priority Sets the switch priority for the specified spanning-tree instance.
Page 762: Spanning-Tree Mst Pre-Standard
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree mst pre-standard spanning-tree mst pre-standard Use the spanning-tree mst pre-standard interface configuration command to configure a port to send only prestandard bridge protocol data units (BPDUs). spanning-tree mst pre-standard no spanning-tree mst pre-standard Syntax Description This command has no arguments or keywords.
Page 763: Spanning-Tree Mst Priority
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree mst priority spanning-tree mst priority Use the spanning-tree mst priority global configuration command on the switch stack or on a standalone switch to set the switch priority for the specified spanning-tree instance. Use the no form of this command to return to the default setting.
Page 764: Spanning-Tree Mst Root
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree mst root spanning-tree mst root Use the spanning-tree mst root global configuration command on the switch stack or on a standalone switch to configure the multiple spanning-tree (MST) root switch priority and timers based on the network diameter.
Page 765 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree mst root When you enter the spanning-tree mst instance-id root secondary command, because of support for the extended system ID, the software changes the switch priority from the default value (32768) to 28672.
Page 766: Spanning-Tree Port-Priority
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree port-priority spanning-tree port-priority Use the spanning-tree port-priority interface configuration command on the switch stack or on a standalone switch to configure an interface priority. If a loop occurs, spanning tree can find the interface to put in the forwarding state.
Page 767 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree port-priority This example shows how to set the port-priority value on VLANs 20 to 25: Switch(config-if)# spanning-tree vlan 20-25 port-priority 0 You can verify your settings by entering the show spanning-tree interface interface-id privileged EXEC command.
Page 768: Spanning-Tree Portfast (Global Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree portfast (global configuration) spanning-tree portfast (global configuration) Use the spanning-tree portfast global configuration command on the switch stack or on a standalone switch to globally enable bridge protocol data unit (BPDU) filtering on Port Fast-enabled interfaces, the BPDU guard feature on Port Fast-enabled interfaces, or the Port Fast feature on all nontrunking interfaces.
Page 769 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree portfast (global configuration) Enabling BPDU filtering on an interface is the same as disabling spanning tree on it and can result in Caution spanning-tree loops. Use the spanning-tree portfast bpduguard default global configuration command to globally enable BPDU guard on interfaces that are in a Port Fast-operational state.
Page 770 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree portfast (global configuration) Related Commands Command Description show running-config Displays the operating configuration. For syntax information, use this link to the Cisco IOS Release 12.2 Command Reference listing page: http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/prod _command_reference_list.html...
Page 771: Spanning-Tree Portfast (Interface Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree portfast (interface configuration) spanning-tree portfast (interface configuration) Use the spanning-tree portfast interface configuration command on the switch stack or on a standalone switch to enable the Port Fast feature on an interface in all its associated VLANs. When the Port Fast feature is enabled, the interface changes directly from a blocking state to a forwarding state without making the intermediate spanning-tree state changes.
Page 772 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree portfast (interface configuration) Examples This example shows how to enable the Port Fast feature on a port: Switch(config)# interface gigabitethernet2/0/2 Switch(config-if)# spanning-tree portfast You can verify your settings by entering the show running-config privileged EXEC command. Related Commands Command Description...
Page 773: Spanning-Tree Transmit Hold-Count
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree transmit hold-count spanning-tree transmit hold-count Use the spanning-tree transmit hold-count global configuration command to configure the number of bridge protocol data units (BPDUs) sent every second. Use the no form of this command to return to the default setting.
Page 774: Spanning-Tree Uplinkfast
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree uplinkfast spanning-tree uplinkfast Use the spanning-tree uplinkfast global configuration command on the switch stack or on a standalone switch to accelerate the choice of a new root port when a link or switch fails or when the spanning tree reconfigures itself.
Page 775 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree uplinkfast Do not enable the root guard on interfaces that will be used by the UplinkFast feature. With UplinkFast, the backup interfaces (in the blocked state) replace the root port in the case of a failure. However, if root guard is also enabled, all the backup interfaces used by the UplinkFast feature are placed in the root-inconsistent state (blocked) and prevented from reaching the forwarding state.
Page 776: Spanning-Tree Vlan
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree vlan spanning-tree vlan Use the spanning-tree vlan global configuration command on the switch stack or on a standalone switch to configure spanning tree on a per-VLAN basis. Use the no form of this command to return to the default setting.
Page 777 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree vlan Defaults Spanning tree is enabled on all VLANs. The forward-delay time is 15 seconds. The hello time is 2 seconds. The max-age is 20 seconds. The primary root switch priority is 24576. The secondary root switch priority is 28672.
Page 778 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands spanning-tree vlan Examples This example shows how to disable the STP on VLAN 5: Switch(config)# no spanning-tree vlan 5 You can verify your setting by entering the show spanning-tree privileged EXEC command. In this instance, VLAN 5 does not appear in the list.
Page 779: Speed
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands speed speed Use the speed interface configuration command on the switch stack or on a standalone switch to specify the speed of a 10/100 Mb/s or 10/100/1000 Mb/s port. Use the no or default form of this command to return the port to its default value.
Page 780 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands speed For guidelines on setting the switch speed and duplex parameters, see the “Configuring Interface Characteristics” chapter in the software configuration guide for this release. Examples This example shows how to set speed on a port to 100 Mb/s: Switch(config)# interface gigabitethernet1/0/17 Switch(config-if)# speed 100 This example shows how to set a port to autonegotiate at only 10 Mb/s:...
Page 781: Srr-Queue Bandwidth Limit
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands srr-queue bandwidth limit srr-queue bandwidth limit Use the srr-queue bandwidth limit interface configuration command on the switch stack or on a standalone switch to limit the maximum output on a port. Use the no form of this command to return to the default setting.
Page 782 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands srr-queue bandwidth limit Related Commands Command Description mls qos queue-set output buffers Allocates buffers to the queue-set. mls qos srr-queue output cos-map Maps class of service (CoS) values to egress queue or maps CoS values to a queue and to a threshold ID.
Page 783: Srr-Queue Bandwidth Shape
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands srr-queue bandwidth shape srr-queue bandwidth shape Use the srr-queue bandwidth shape interface configuration command on the switch stack or on a standalone switch to assign the shaped weights and to enable bandwidth shaping on the four egress queues mapped to a port.
Page 784 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands srr-queue bandwidth shape Examples This example shows how to configure the queues for the same port for both shaping and sharing. Because the weight ratios for queues 2, 3, and 4 are set to 0, these queues operate in shared mode. The bandwidth weight for queue 1 is 1/8, which is 12.5 percent.
Page 785: Srr-Queue Bandwidth Share
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands srr-queue bandwidth share srr-queue bandwidth share Use the srr-queue bandwidth share interface configuration command on the switch stack or on a standalone switch to assign the shared weights and to enable bandwidth sharing on the four egress queues mapped to a port.
Page 786 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands srr-queue bandwidth share Examples This example shows how to configure the weight ratio of the SRR scheduler running on an egress port. Four queues are used. The bandwidth ratio allocated for each queue in shared mode is 1/(1+2+3+4), 2/(1+2+3+4), 3/(1+2+3+4), and 4/(1+2+3+4), which is 10 percent, 20 percent, 30 percent, and 40 percent for queues 1, 2, 3, and 4.
Page 787: Stack-Mac Persistent Timer
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands stack-mac persistent timer stack-mac persistent timer Use the stack-mac persistent timer global configuration command on the switch stack or on a standalone switch to enable the persistent MAC address feature. When this feature is enabled, if the stack master changes, the stack MAC address does not change for approximately four minutes, for an indefinite time period, or for a configured time value.
Page 788 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands stack-mac persistent timer Examples This examples shows how to enable persistent MAC address: Switch(config)# stack-mac persistent timer You can verify your settings by entering the show running-config privileged EXEC command. If enabled, stack-mac persistent timer is shown in the output.
Page 789: Storm-Control
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands storm-control storm-control Use the storm-control interface configuration command on the switch stack or on a standalone switch to enable broadcast, multicast, or unicast storm control and to set threshold levels on an interface. Use the no form of this command to return to the default setting.
Page 790 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands storm-control level pps pps Specify the rising and falling suppression levels as a rate in packets per second at [pps-low] which traffic is received on the port. pps—Rising suppression level, up to 1 decimal place. The range is 0.0 to •...
Page 791 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands storm-control If you configure the action to be taken as shutdown (the port is error-disabled during a storm) when a packet storm is detected, you must use the no shutdown interface configuration command to bring the interface out of this state.
Page 792: Switch
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switch switch Use the switch privileged EXEC on a stack member to disable or enable the specified stack port on the member. switch stack-member-number stack port port-number {disable | enable} Note This command is supported only on stacking-capable switches.
Page 793 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switch Examples This example shows how to disable stack port 2 on member 4: Switch# switch 4 stack port 2 disable Related Commands Command Description show switch Displays information about the switch stack and the stack members. Cisco Catalyst Blade Switch 3120 for HP Command Reference 2-763 OL-12248-03...
Page 794: Switch Priority
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switch priority switch priority Use the switch priority global configuration command on the stack master to change the stack member priority value. switch stack-member-number priority new-priority-value Note This command is supported only on stacking-capable switches. Syntax Description stack-member-number Specify the current stack member number.
Page 795: Switch Provision
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switch provision switch provision Use the switch provision global configuration command on the stack master to provision (to supply a configuration to) a new switch before it joins the switch stack. Use the no form of this command to delete all configuration information associated with the removed switch (a stack member that has left the stack).
Page 796 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switch provision When you use this command, memory is allocated for the provisioned configuration. When a new switch Caution type is configured, the previously allocated memory is not fully released. Therefore, do not use this command more than approximately 200 times, or the switch will run out of memory and unexpected behavior will result.
Page 797: Switch Renumber
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switch renumber switch renumber Use the switch renumber global configuration command on the stack master to change the stack member number. switch current-stack-member-number renumber new-stack-member-number Note This command is supported only on stacking-capable switches. Syntax Description current-stack-member-number Specify the current stack member number.
Page 798 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switch renumber Related Commands Command Description reload Reloads the stack member and puts a configuration change into effect. session Accesses a specific stack member. switch priority Changes the stack member priority value. show switch Displays information about the switch stack and its stack members.
Page 799: Switchport
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport switchport Use the switchport interface configuration command with no keywords on the switch stack or on a standalone switch to put an interface that is in Layer 3 mode into Layer 2 mode for Layer 2 configuration. Use the no form of this command to put an interface in Layer 3 mode.
Page 800 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport The switchport command without keywords is not used on platforms that do not support Cisco-routed Note ports. All physical ports on such platforms are assumed to be Layer 2-switched interfaces. You can verify the switchport status of an interface by entering the show running-config privileged EXEC command.
Page 801: Switchport Access
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport access switchport access Use the switchport access interface configuration command on the switch stack or on a standalone switch to configure a port as a static-access or dynamic-access port. If the switchport mode is set to access, the port operates as a member of the specified VLAN.
Page 802 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport access These restrictions apply to dynamic-access ports: The software implements the VLAN Query Protocol (VQP) client, which can query a VMPS such • as a Catalyst 6000 series switch. The switches are not VMPS servers. The VMPS server must be configured before a port is configured as dynamic.
Page 803: Switchport Autostate Exclude
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport autostate exclude switchport autostate exclude Use the switchport autostate exclude interface configuration command to exclude an interface from the VLAN interface (switch virtual interface) line state up or down calculation. Use the no form of this command to return to the default setting.
Page 804 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport autostate exclude Administrative Native VLAN tagging: enabled Voice VLAN: none Administrative private-vlan host-association: none Administrative private-vlan mapping: none Administrative private-vlan trunk native VLAN: none Administrative private-vlan trunk Native VLAN tagging: enabled Administrative private-vlan trunk encapsulation: dot1q Administrative private-vlan trunk normal VLANs: none Administrative private-vlan trunk associations: none...
Page 805: Switchport Backup Interface
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport backup interface switchport backup interface Use the switchport backup interface interface configuration command on a Layer 2 interface on the switch stack or on a standalone switch to configure Flex Links, a pair of interfaces that provide backup to each other.
Page 806 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport backup interface Usage Guidelines With Flex Links configured, one link acts as the primary interface and forwards traffic, while the other interface is in standby mode, ready to begin forwarding traffic if the primary link shuts down. The interface being configured is referred to as the active link;...
Page 807 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport backup interface Related Commands Command Description show interfaces [interface-id] Displays the configured Flex Links and their status on the switch or switchport backup for the specified interface. Cisco Catalyst Blade Switch 3120 for HP Command Reference 2-777 OL-12248-03...
Page 808: Switchport Block
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport block switchport block Use the switchport block interface configuration command on the switch stack or on a standalone switch to prevent unknown multicast or unicast packets from being forwarded. Use the no form of this command to allow forwarding unknown multicast or unicast packets.
Page 809: Switchport Host
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport host switchport host Use the switchport host interface configuration command on the switch stack or on a standalone switchto optimize a Layer 2 port for a host connection. The no form of this command has no affect on the system. switchport host Syntax Description This command has no arguments or keywords.
Page 810: Switchport Mode
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport mode switchport mode Use the switchport mode interface configuration command on the switch stack or on a standalone switch to configure the VLAN membership mode of a port. Use the no form of this command to reset the mode to the appropriate default for the device.
Page 811 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport mode When you enter dynamic desirable mode, the interface becomes a trunk interface if the neighboring interface is set to trunk, desirable, or auto mode. To autonegotiate trunking, the interfaces must be in the same VLAN Trunking Protocol (VTP) domain. Trunk negotiation is managed by the Dynamic Trunking Protocol (DTP), which is a point-to-point protocol.
Page 812 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport mode Examples This example shows how to configure a port for access mode: Switch(config)# interface gigabitethernet2/0/1 Switch(config-if)# switchport mode access This example shows how set the port to dynamic desirable mode: Switch(config)# interface gigabitethernet2/0/1 Switch(config-if)# switchport mode dynamic desirable This example shows how to configure a port for trunk mode:...
Page 813: Switchport Mode Private-Vlan
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport mode private-vlan switchport mode private-vlan Use the switchport mode private-vlan interface configuration command on the switch stack or on a standalone switch to configure a port as a promiscuous or host private VLAN port. Use the no form of this command to reset the mode to the appropriate default for the device.
Page 814 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport mode private-vlan For more information about private-VLAN interaction with other features, see the software configuration guide for this release. We strongly recommend that you enable spanning tree Port Fast and bridge-protocol-data-unit (BPDU) guard on isolated and community host ports to prevent STP loops due to misconfigurations and to speed up STP convergence.
Page 815: Switchport Nonegotiate
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport nonegotiate switchport nonegotiate Use the switchport nonegotiate interface configuration command on the switch stack or on a standalone switch to specify that Dynamic Trunking Protocol (DTP) negotiation packets are not sent on the Layer 2 interface.
Page 816 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport nonegotiate Examples This example shows how to cause a port to refrain from negotiating trunking mode and to act as a trunk or access port (depending on the mode set): Switch(config)# interface gigabitethernet2/0/1 Switch(config-if)# switchport nonegotiate You can verify your setting by entering the show interfaces interface-id switchport privileged EXEC...
Page 817: Switchport Port-Security
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport port-security switchport port-security Use the switchport port-security interface configuration command without keywords on the switch stack or on a standalone switch to enable port security on the uplink interface. Use the keywords to configure secure MAC addresses, sticky MAC address learning, a maximum number of secure MAC addresses, or the violation mode.
Page 818 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport port-security vlan [vlan-list] (Optional) For trunk ports, you can set the maximum number of secure MAC addresses on a VLAN. If the vlan keyword is not entered, the default value is used.
Page 819 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport port-security Command History Release Modification 12.2(40)EX1 This command was introduced. Usage Guidelines A secure port has the following limitations: A secure port can be an access port or a trunk port; it cannot be a dynamic access port. •...
Page 820 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport port-security Sticky secure MAC addresses have these characteristics: When you enable sticky learning on an interface by using the switchport port-security • mac-address sticky interface configuration command, the interface converts all the dynamic secure MAC addresses, including those that were dynamically learned before sticky learning was enabled, to sticky secure MAC addresses and adds all sticky secure MAC addresses to the running configuration.
Page 821 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport port-security Related Commands Command Description clear port-security Deletes from the MAC address table a specific type of secure address or all the secure addresses on the switch or an interface. show port-security address Displays all the secure addresses configured on the switch.
Page 822: Switchport Port-Security Aging
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport port-security aging switchport port-security aging Use the switchport port-security aging interface configuration command on the switch stack or on a standalone switch to set the aging time and type for secure address entries or to change the aging behavior for secure addresses on a particular port.
Page 823 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport port-security aging Examples This example sets the aging time as 2 hours for absolute aging for all the secure addresses on the port: Switch(config)# interface gigabitethernet1/0/1 Switch(config-if)# switchport port-security aging time 120 This example sets the aging time as 2 minutes for inactivity aging type with aging enabled for configured secure addresses on the port: Switch(config)# interface gigabitethernet1/0/2...
Page 824: Switchport Priority Extend
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport priority extend switchport priority extend Use the switchport priority extend interface configuration command on the switch stack or on a standalone switch to set a port priority for the incoming untagged frames or the priority of frames received by the IP phone connected to the specified port.
Page 825 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport priority extend Related Commands Command Description show interfaces Displays the administrative and operational status of a switching (nonrouting) port. switchport voice vlan Configures the voice VLAN on the port. Cisco Catalyst Blade Switch 3120 for HP Command Reference 2-795 OL-12248-03...
Page 826: Switchport Private-Vlan
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport private-vlan switchport private-vlan Use the switchport private-vlan interface configuration command on the switch stack or on a standalone switch to define a private-VLAN association for an isolated or community port or a mapping for a promiscuous port.
Page 827 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport private-vlan The secondary_vlan_list parameter cannot contain spaces. It can contain multiple comma-separated items. Each item can be a single private-VLAN ID or a hyphenated range of private-VLAN IDs. The list can contain one isolated VLAN and multiple community VLANs.
Page 828: Switchport Protected
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport protected switchport protected Use the switchport protected interface configuration command on the switch stack or on a standalone switch to isolate unicast, multicast, and broadcast traffic at Layer 2 from other protected ports on the same switch.
Page 829 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport protected Related Commands Command Description show interfaces Displays the administrative and operational status of a switching (nonrouting) switchport port, including port blocking and port protection settings. switchport block Prevents unknown multicast or unicast traffic on the interface.
Page 830: Switchport Trunk
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport trunk switchport trunk Use the switchport trunk interface configuration command on the switch stack or on a standalone switch to set the trunk characteristics when the interface is in trunking mode. Use the no form of this command to reset a trunking characteristic to the default.
Page 831 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport trunk remove removes the defined list of VLANs from those currently set instead of replacing the list. • Valid IDs are from 1 to 1005; extended-range VLAN IDs are valid in some cases. You can remove extended-range VLANs from the allowed VLAN list, but you cannot Note remove them from the pruning-eligible list.
Page 832 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport trunk Allowed VLAN: To reduce the risk of spanning-tree loops or storms, you can disable VLAN 1 on any individual • VLAN trunk port by removing VLAN 1 from the allowed list. When you remove VLAN 1 from a trunk port, the interface continues to send and receive management traffic, for example, Cisco Discovery Protocol (CDP), Port Aggregation Protocol (PAgP), Link Aggregation Control Protocol (LACP), Dynamic Trunking Protocol (DTP), and VLAN Trunking Protocol (VTP) in VLAN 1.
Page 833: Switchport Voice Detect
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport voice detect switchport voice detect Use the switchport voice detect interface configuration command on the switch stack or on a standalone switch to detect and recognize a Cisco IP phone. Use the no form of this command to return to the default setting.
Page 834: Switchport Voice Vlan
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport voice vlan switchport voice vlan Use the switchport voice vlan interface configuration command on the switch stack or on a standalone switch to configure voice VLAN on the port. Use the no form of this command to return to the default setting.
Page 835 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands switchport voice vlan When you enable port security on an interface that is also configured with a voice VLAN, set the maximum allowed secure addresses on the port to two. When the port is connected to a Cisco IP phone, the IP phone requires one MAC address.
Page 836: System Env Temperature Threshold Yellow
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands system env temperature threshold yellow system env temperature threshold yellow Use the system env temperature threshold yellow global configuration command on the switch stack or on a standalone switch to configure the difference between the yellow and red temperature thresholds that determines the value of yellow threshold.
Page 837 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands system env temperature threshold yellow Examples This example sets 15 as the difference between the yellow and red thresholds: Switch(config)# system env temperature threshold yellow 15 Switch(config)# Related Commands Command Description show env...
Page 838: System Mtu
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands system mtu system mtu Use the system mtu global configuration command on the switch stack or on a standalone switch to set the maximum packet size or maximum transmission unit (MTU) size for Gigabit Ethernet (10/100/1000) ports, for 10-Gigabit ports, or for routed ports.
Page 839 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands system mtu The upper limit of the system routing MTU value is based on the switch or switch stack configuration and refers to the currently applied system jumbo MTU value. If you enter a value that is outside the allowed range for the specific type of interface, the value is not accepted.
Page 840: Test Cable-Diagnostics Tdr
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands test cable-diagnostics tdr test cable-diagnostics tdr Use the test cable-diagnostics tdr privileged EXEC command on the switch stack or on a standalone switch to run the Time Domain Reflector (TDR) feature on an interface. test cable-diagnostics tdr interface interface-id Syntax Description interface-id...
Page 841: Traceroute Mac
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands traceroute mac traceroute mac Use the traceroute mac privileged EXEC command on the switch stack or on a standalone switch to display the Layer 2 path taken by the packets from the specified source MAC address to the specified destination MAC address.
Page 842 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands traceroute mac The Layer 2 traceroute feature is not supported when multiple devices are attached to one port through hubs (for example, multiple CDP neighbors are detected on a port). When more than one CDP neighbor is detected on a port, the Layer 2 path is not identified, and an error message appears.
Page 843 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands traceroute mac This example shows the Layer 2 path when the switch cannot find the destination port for the source MAC address: Switch# traceroute mac 0000.0011.1111 0000.0201.0201 Error:Source Mac address not found. Layer2 trace aborted.
Page 844: Traceroute Mac Ip
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands traceroute mac ip traceroute mac ip Use the traceroute mac ip privileged EXEC command on the switch stack or on a standalone switch to display the Layer 2 path taken by the packets from the specified source IP address or hostname to the specified destination IP address or hostname.
Page 845 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands traceroute mac ip The Layer 2 traceroute feature is not supported when multiple devices are attached to one port through hubs (for example, multiple CDP neighbors are detected on a port). When more than one CDP neighbor is detected on a port, the Layer 2 path is not identified, and an error message appears.
Page 846: Trust
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands trust trust Use the trust policy-map class configuration command on the switch stack or on a standalone switch to define a trust state for traffic classified through the class policy-map configuration or the class-map global configuration command.
Page 847 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands trust If you specify trust ip-precedence, QoS uses the IP precedence value from the ingress packet and the IP-precedence-to-DSCP map. For non-IP packets that are tagged, QoS uses the received CoS value; for non-IP packets that are untagged, QoS uses the default port CoS value.
Page 848: Udld
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands udld udld Use the udld global configuration command on the switch stack or on a standalone switch to enable aggressive or normal mode in the UniDirectional Link Detection (UDLD) and to set the configurable message timer time.
Page 849: Udld Reset
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands udld The no udld port interface configuration command followed by the udld port or udld port • aggressive interface configuration command to re-enable UDLD on the specified interface •...
Page 850: Udld Port
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands udld port udld port Use the udld port interface configuration command on the switch stack or on a standalone switch to enable the UniDirectional Link Detection (UDLD) on an individual interface or prevent a fiber-optic interface from being enabled by the udld global configuration command.
Page 851 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands udld port You can use these commands to reset an interface shut down by UDLD: The udld reset privileged EXEC command to reset all interfaces shut down by UDLD •...
Page 852: Udld Reset
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands udld reset udld reset Use the udld reset privileged EXEC command to reset all interfaces disabled by the UniDirectional Link Detection (UDLD) and permit traffic to begin passing through them again (though other features, such as spanning tree, Port Aggregation Protocol (PAgP), and Dynamic Trunking Protocol (DTP) still have their normal effects, if enabled).
Page 853: Vlan (Global Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vlan (global configuration) vlan (global configuration) Use the vlan global configuration command on the switch stack or on a standalone switch to add a VLAN and to enter the config-vlan mode. Use the no form of this command to delete the VLAN. Configuration information for normal-range VLANs (VLAN IDs 1 to 1005) is always saved in the VLAN database.
Page 854 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vlan (global configuration) If you enter an invalid VLAN ID, you receive an error message and do not enter config-vlan mode. Entering the vlan command with a VLAN ID enables config-vlan mode. When you enter the VLAN ID of an existing VLAN, you do not create a new VLAN, but you can modify VLAN parameters for that VLAN.
Page 855 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vlan (global configuration) name vlan-name: names the VLAN with an ASCII string from 1 to 32 characters that must be unique • within the administrative domain. The default is VLANxxxx where xxxx represents four numeric digits (including leading zeros) equal to the VLAN ID number.
Page 856 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vlan (global configuration) Table 2-40 for valid commands and syntax for different media types. Table 2-40 Valid Commands and Syntax for Different Media Types Media Type Valid Syntax Ethernet name vlan-name, media ethernet, state {suspend | active}, said said-value, mtu mtu-size, remote-span, tb-vlan1 tb-vlan1-id, tb-vlan2 tb-vlan2-id...
Page 857 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vlan (global configuration) Table 2-41 VLAN Configuration Rules (continued) Configuration Rule VTP v2 mode is enabled, and you Specify a bridge number. Do not leave this field blank. are configuring a TrBRF VLAN media type.
Page 858 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vlan (global configuration) Related Commands Command Description show vlan Displays the parameters for all configured VLANs or one VLAN (if the VLAN ID or name is specified) in the administrative domain. vlan (VLAN Configures normal-range VLANs in the VLAN database.
Page 859: Vlan (Vlan Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vlan (VLAN configuration) vlan (VLAN configuration) Use the vlan VLAN configuration command on the switch stack or on a standalone switch to configure VLAN characteristics for a normal-range VLAN (VLAN IDs 1 to 1005) in the VLAN database. You access VLAN configuration mode by entering the vlan database privileged EXEC command.
Page 860 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vlan (VLAN configuration) media {ethernet | fddi | (Optional) Specify the VLAN media type. Table 2-42 lists the valid fd-net | tokenring | tr-net} syntax for each media type. ethernet is Ethernet media type (the default).
Page 861 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vlan (VLAN configuration) Table 2-42 shows the valid syntax options for different media types. Table 2-42 Valid Syntax for Different Media Types Media Type Valid Syntax Ethernet vlan vlan-id [name vlan-name] media ethernet [state {suspend | active}] [said said-value] [mtu mtu-size] [tb-vlan1 tb-vlan1-id] [tb-vlan2 tb-vlan2-id] FDDI vlan vlan-id [name vlan-name] media fddi [state {suspend | active}]...
Page 862 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vlan (VLAN configuration) Table 2-43 VLAN Configuration Rules (continued) Configuration Rule VTP v2 mode is enabled, and you Specify a bridge number. Do not leave this field blank. are configuring a TrBRF VLAN media type.
Page 863 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vlan (VLAN configuration) Command History Release Modification 12.2(40)EX1 This command was introduced. Usage Guidelines You can only use this command mode for configuring normal-range VLANs, that is, VLAN IDs 1 to 1005.
Page 864 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vlan (VLAN configuration) When the no vlan vlan-id state form is used, the VLAN state returns to the default (active). • When the no vlan vlan-id stp type form is used, the VLAN spanning-tree type returns to the default •...
Page 865: Vlan Access-Map
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vlan access-map vlan access-map Use the vlan access-map global configuration command on the switch stack or on a standalone switch to create or modify a VLAN map entry for VLAN packet filtering. This entry changes the mode to the VLAN access-map configuration.
Page 866 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vlan access-map You can use the no vlan access-map name [number] command with a sequence number to delete a single entry. In global configuration mode, use the vlan filter interface configuration command to apply the map to one or more VLANs.
Page 867: Vlan Database
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vlan database vlan database Use the vlan database privileged EXEC command on the switch stack or on a standalone switch to enter VLAN configuration mode. From this mode, you can add, delete, and modify VLAN configurations for normal-range VLANs and globally propagate these changes by using the VLAN Trunking Protocol (VTP).
Page 868 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vlan database When you have modified VLAN or VTP parameters, you can use these editing buffer manipulation commands: • abort: exits the mode without applying the changes. The VLAN configuration that was running before you entered VLAN configuration mode continues to be used.
Page 869 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vlan database VLAN ISL Id: 1002 Name: fddi-default Media Type: FDDI VLAN 802.10 Id: 101002 State: Operational MTU: 1500 Bridge Type: SRB Ring Number: 0 Translational Bridged VLAN: 1 Translational Bridged VLAN: 1003 <output truncated>...
Page 870: Vlan Dot1Q Tag Native
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vlan dot1q tag native vlan dot1q tag native Use the vlan dot1q tag native global configuration command on the switch stack or on a standalone switch to enable tagging of native VLAN frames on all IEEE 802.1Q trunk ports. Use the no form of this command to return to the default setting.
Page 871 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vlan dot1q tag native Related Commands Command Description show vlan dot1q tag native Displays IEEE 802.1Q native VLAN tagging status. Cisco Catalyst Blade Switch 3120 for HP Command Reference 2-841 OL-12248-03...
Page 872: Vlan Filter
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vlan filter vlan filter Use the vlan filter global configuration command on the switch stack or on a standalone switch to apply a VLAN map to one or more VLANs. Use the no form of this command to remove the map. vlan filter mapname vlan-list {list | all} no vlan filter mapname vlan-list {list | all} Syntax Description...
Page 873 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vlan filter Related Commands Command Description show vlan access-map Displays information about a particular VLAN access map or all VLAN access maps. show vlan filter Displays information about all VLAN filters or about a particular VLAN or VLAN access map.
Page 874: Vmps Reconfirm (Privileged Exec)
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vmps reconfirm (privileged EXEC) vmps reconfirm (privileged EXEC) Use the vmps reconfirm privileged EXEC command on the switch stack or on a standalone switch to immediately send VLAN Query Protocol (VQP) queries to reconfirm all dynamic VLAN assignments with the VLAN Membership Policy Server (VMPS).
Page 875: Vmps Reconfirm (Global Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vmps reconfirm (global configuration) vmps reconfirm (global configuration) Use the vmps reconfirm global configuration command on the switch stack or on a standalone switch to change the reconfirmation interval for the VLAN Query Protocol (VQP) client. Use the no form of this command to return to the default setting.
Page 876: Vmps Retry
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vmps retry vmps retry Use the vmps retry global configuration command on the switch stack or on a standalone switch to configure the per-server retry count for the VLAN Query Protocol (VQP) client. Use the no form of this command to return to the default setting.
Page 877: Vmps Server
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vmps server vmps server Use the vmps server global configuration command on the switch stack or on a standalone switch to configure the primary VLAN Membership Policy Server (VMPS) and up to three secondary servers. Use the no form of this command to remove a VMPS server.
Page 878 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vmps server Related Commands Command Description show vmps Displays VQP and VMPS information. Cisco Catalyst Blade Switch 3120 for HP Command Reference 2-848 OL-12248-03...
Page 879: Vtp (Global Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vtp (global configuration) vtp (global configuration) Use the vtp global configuration command on the switch stack or on a standalone switch to set or modify the VLAN Trunking Protocol (VTP) configuration characteristics. Use the no form of this command to remove the settings or to return to the default settings.
Page 880 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vtp (global configuration) Defaults The default filename is flash:vlan.dat. The default mode is server mode. No domain name or password is defined. No password is configured. Pruning is disabled. The default version is Version 1.
Page 881 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vtp (global configuration) Follow these guidelines when setting VTP mode: The no vtp mode command returns the switch to VTP server mode. • The vtp mode server command is the same as no vtp mode except that it does not return an error •...
Page 882 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vtp (global configuration) If you are configuring a Token Ring bridge relay function (TrBRF) or Token Ring concentrator relay • function (TrCRF) VLAN media type, you must use Version 2. •...
Page 883: Vtp (Vlan Configuration)
Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vtp (VLAN configuration) vtp (VLAN configuration) Use the vtp VLAN configuration command on the switch stack or on a standalone switch to configure VLAN Trunking Protocol (VTP) characteristics. You access VLAN configuration mode by entering the vlan database privileged EXEC command.
Page 884 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vtp (VLAN configuration) Command Modes VLAN configuration Command History Release Modification 12.2(40)EX1 This command was introduced. Usage Guidelines If the VTP mode is transparent, the mode and domain name are saved in the switch running configuration file, and you can save the configuration in the switch startup configuration file by using the copy running-config startup-config privileged EXEC command.
Page 885 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vtp (VLAN configuration) Domain names are case sensitive. • After you configure a domain name, it cannot be removed. You can reassign it only to a different • domain.
Page 886 Chapter 2 Cisco Catalyst Blade Switch 3120 for HP Cisco IOS Commands vtp (VLAN configuration) Related Commands Command Description show vtp status Displays the VTP statistics for the switch and general information about the VTP management domain status. switchport trunk Configures the VLAN pruning-eligible list for ports in trunking mode.
Page 887: Appendix
Mode button. You should then see the boot loader Switch: prompt. The boot loader performs low-level CPU initialization, performs POST, and loads a default operating system image into memory. Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference OL-13271-03...
Page 888: Arp
Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands Use the arp boot loader command to display the contents the Address Resolution Protocol (ARP) table. arp [ip_address] Syntax Description ip_address (Optional) Show the ARP table or the mapping for a specific IP address.
Page 889: Boot
Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands boot boot Use the boot boot loader command to load and boot an executable image and to enter the command-line interface. boot [-post | -n | -p | flag] filesystem:/file-url ...
Page 890 Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands boot Related Commands Command Description Sets the BOOT environment variable to boot a specific image when the BOOT keyword is appended to the command. Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference...
Page 891: Cat
Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands Use the cat boot loader command to display the contents of one or more files. cat filesystem:/file-url ... Syntax Description filesystem: Alias for a flash file system. Use flash: for the system board flash device.
Page 892: Copy
Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands copy copy Use the copy boot loader command to copy a file from a source to a destination. copy [-b block-size] filesystem:/source-file-url filesystem:/destination-file-url Syntax Description -b block-size (Optional) This option is used only for internal development and testing.
Page 893 Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands delete delete Use the delete boot loader command to delete one or more files from the specified file system. delete filesystem:/file-url ... Syntax Description filesystem: Alias for a flash file system. Use flash: for the system board flash device.
Page 894: Dir
Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands Use the dir boot loader command to display a list of files and directories on the specified file system. dir filesystem:/file-url ... Syntax Description filesystem: Alias for a flash file system. Use flash: for the system board flash device.
Page 895 Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands Table A-1 dir Field Descriptions (continued) Field Description <date> Last modification date. env_vars Filename. Related Commands Command Description mkdir Creates one or more directories. rmdir Removes one or more directories.
Page 896: Flash_Init
Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands flash_init flash_init Use the flash_init boot loader command to initialize the flash file system. flash_init Syntax Description This command has no arguments or keywords. Defaults The flash file system is automatically initialized during normal system operation.
Page 897: Format
Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands format format Use the format boot loader command to format the specified file system and destroy all data in that file system. format filesystem: Syntax Description filesystem: Alias for a flash file system.
Page 898: Fsck
Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands fsck fsck Use the fsck boot loader command to check the file system for consistency. fsck [-test | -f] filesystem: Syntax Description -test (Optional) Initialize the file system code and perform extra POST on flash memory.
Page 899: Help
Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands help help Use the help boot loader command to display the available commands. help Syntax Description This command has no arguments or keywords. Command Modes Boot loader...
Page 900: Memory
Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands memory memory Use the memory boot loader command to display memory heap utilization information. memory Syntax Description This command has no arguments or keywords. Command Modes...
Page 901 Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands memory Table A-2 memory Field Descriptions (continued) Field Description Stack Beginning and ending address of the area in memory allocated to the software to store automatic variables, return addresses, and so forth.
Page 902: Mgmt_Clr
Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands mgmt_clr mgmt_clr Use the mgmt_clr boot loader command to clear the Ethernet management port statistics. mgmt_clr Syntax Description This command has no arguments or keywords. Command Modes...
Page 903: Mgmt_Init
Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands mgmt_init mgmt_init Use the mgmt_init boot loader command to initialize the Ethernet management port. mgmt_init Syntax Description This command has no arguments or keywords. Command Modes...
Page 904: Mgmt_Show
Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands mgmt_show mgmt_show Use the mgmt_show boot loader command to display the Ethernet management port statistics. mgmt_show Syntax Description This command has no arguments or keywords. Command Modes...
Page 905: Mkdir
Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands mkdir mkdir Use the mkdir boot loader command to create one or more new directories on the specified file system. mkdir filesystem:/directory-url ... Syntax Description filesystem: Alias for a flash file system.
Page 906: More
Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands more more Use the more boot loader command to display the contents of one or more files. more filesystem:/file-url ... Syntax Description filesystem: Alias for a flash file system. Use flash: for the system board flash device.
Page 907: Rename
Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands rename rename Use the rename boot loader command to rename a file. rename filesystem:/source-file-url filesystem:/destination-file-url Syntax Description filesystem: Alias for a flash file system. Use flash: for the system board flash device.
Page 908: Reset
Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands reset reset Use the reset boot loader command to perform a hard reset on the system. A hard reset is similar to power-cycling the switch, clearing the processor, registers, and memory.
Page 909: Rmdir
Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands rmdir rmdir Use the rmdir boot loader command to remove one or more empty directories from the specified file system. rmdir filesystem:/directory-url ... Syntax Description filesystem: Alias for a flash file system.
Page 910: Set
Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands Use the set boot loader command to set or display environment variables, which can be used to control the boot loader or any other software running on the switch.
Page 911 Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands Defaults The environment variables have these default values: MANUAL_BOOT: No (0) BOOT: Null string ENABLE_BREAK: No (Off or 0) (the automatic boot process cannot be interrupted by pressing the Break key on the console).
Page 912: Unset
Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands For stacking-capable switches, the SWITCH_NUMBER environment variable can also be set by using the switch current-stack-member-number renumber new-stack-member-number global configuration command. For stacking-capable switches, the SWITCH_PRIORITY environment variable can also be set by using the switch stack-member-number priority priority-number global configuration command.
Page 913 Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands type type Use the type boot loader command to display the contents of one or more files. type filesystem:/file-url ... Syntax Description filesystem: Alias for a flash file system. Use flash: for the system board flash device.
Page 914 Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands unset unset Use the unset boot loader command to reset one or more environment variables. unset variable ... Syntax Description variable Use one of these keywords for variable: MANUAL_BOOT—Decides whether the switch automatically or manually...
Page 915 Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands unset Usage Guidelines Under normal circumstances, it is not necessary to alter the setting of the environment variables. The MANUAL_BOOT environment variable can also be reset by using the no boot manual global configuration command.
Page 916: Version
Appendix A Cisco Catalyst Blade Switch 3130 and 3032 for Dell Boot Loader Commands version version Use the version boot loader command to display the boot loader version. version Syntax Description This command has no arguments or keywords. Command Modes...
Page 917: Appendix
Cisco technical support staff. It is best to use the debug commands during periods of lower network traffic and fewer users. Debugging during these periods decreases the likelihood that increased debug command processing overhead will affect system use. Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference OL-13271-03...
Page 918: A P P E N D I X B Cisco Catalyst Blade Switch 3130 And 3032 For Dell Debug Commands
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug auto qos debug auto qos Use the debug auto qos privileged EXEC command to enable debugging of the automatic quality of service (auto-QoS) feature. Use the no form of this command to disable debugging.
Page 919 Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug auto qos 21:29:42: mls qos srr-queue input cos-map queue 2 threshold 1 2 21:29:42: mls qos srr-queue input cos-map queue 2 threshold 2 4 6 7...
Page 920: Debug Backup
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug backup debug backup Use the debug backup privileged EXEC command to enable debugging of the Flex Links backup interface. Use the no form of this command to disable debugging.
Page 921: Debug Cisp
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug cisp debug cisp Use the debug cisp global configuration command to enable debugging message exchanges and events on a Client Information Signalling Protocol (CISP)-enabled interface.Use the no form of this command to disable debugging.
Page 922: Debug Dot1X
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug dot1x debug dot1x Use the debug dot1x privileged EXEC command to enable debugging of the IEEE 802.1x authentication feature. Use the no form of this command to disable debugging.
Page 923: Debug Dtp
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug dtp debug dtp Use the debug dtp privileged EXEC command to enable debugging of the Dynamic Trunking Protocol (DTP) activity. Use the no form of this command to disable debugging.
Page 924: Debug Eap
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug eap debug eap Use the debug eap privileged EXEC command to enable debugging of the Extensible Authentication Protocol (EAP) activity. Use the no form of this command to disable debugging.
Page 925: Debug Etherchannel
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug etherchannel debug etherchannel Use the debug etherchannel privileged EXEC command to enable debugging of the EtherChannel/PAgP shim. This shim is the software module that is the interface between the Port Aggregation Protocol (PAgP) software module and the port manager software module.
Page 926: Debug Fastethernet
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug fastethernet debug fastethernet Use the debug fastethernet privileged EXEC command to enable debugging of the Ethernet management port. Use the no form of this command to disable debugging.
Page 927: Debug Ip Dhcp Snooping
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug ip dhcp snooping debug ip dhcp snooping Use the debug ip dhcp snooping privileged EXEC command to enable debugging of DHCP snooping. Use the no form of this command to disable debugging.
Page 928: Debug Ip Verify Source Packet
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug ip verify source packet debug ip verify source packet Use the debug ip verify source packet privileged EXEC command to enable debugging of IP source guard. Use the no form of this command to disable debugging.
Page 929: Debug Interface
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug interface debug interface Use the debug interface privileged EXEC command to enable debugging of interface-related activities. Use the no form of this command to disable debugging.
Page 930: Debug Ip Igmp Filter
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug ip igmp filter debug ip igmp filter Use the debug ip igmp filter privileged EXEC command to enable debugging of Internet Group Management Protocol (IGMP) filter events. Use the no form of this command to disable debugging.
Page 931: Debug Ip Igmp Max-Groups
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug ip igmp max-groups debug ip igmp max-groups Use the debug ip igmp max-groups privileged EXEC command to enable debugging of Internet Group Management Protocol (IGMP) maximum groups events. Use the no form of this command to disable debugging.
Page 932: Debug Ip Igmp Snooping
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug ip igmp snooping debug ip igmp snooping Use the debug igmp snooping privileged EXEC command to enable debugging of Internet Group Management Protocol (IGMP) snooping activity. Use the no form of this command to disable debugging.
Page 933: Debug Lacp
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug lacp debug lacp Use the debug lacp privileged EXEC command to enable debugging of Link Aggregation Control Protocol (LACP) activity. Use the no form of this command to disable debugging.
Page 934: Debug Lldp Packets
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug lldp packets debug lldp packets Use the debug lldp packets privileged EXEC command to enable debugging of Link Layer Discovery Protocol (LLDP) packets. Use the no form of this command to disable debugging.
Page 935: Debug Mac-Notification
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug mac-notification debug mac-notification Use the debug mac-notification privileged EXEC command to enable debugging of MAC notification events. Use the no form of this command to disable debugging.
Page 936: Debug Matm
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug matm debug matm Use the debug matm privileged EXEC command to enable debugging of platform-independent MAC address management. Use the no form of this command to disable debugging.
Page 937: Debug Matm Move Update
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug matm move update debug matm move update Use the debug matm move update privileged EXEC command to enable debugging of MAC address-table move update message processing.
Page 938: Debug Monitor
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug monitor debug monitor Use the debug monitor privileged EXEC command to enable debugging of the Switched Port Analyzer (SPAN) feature. Use the no form of this command to disable debugging.
Page 939: Debug Mvrdbg
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug mvrdbg debug mvrdbg Use the debug mvrdbg privileged EXEC command to enable debugging of Multicast VLAN Registration (MVR). Use the no form of this command to disable debugging.
Page 940: Debug Nmsp
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug nmsp debug nmsp Use the debug nmsp privileged EXEC command to the enable debugging of the Network Mobility Services Protocol (NMSP) on the switch. This command is available only when your switch is running the cryptographic (encrypted) software image.
Page 941: Debug Nvram
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug nvram debug nvram Use the debug nvram privileged EXEC command to enable debugging of NVRAM activity. Use the no form of this command to disable debugging.
Page 942: Debug Pagp
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug pagp debug pagp Use the debug pagp privileged EXEC command to enable debugging of Port Aggregation Protocol (PAgP) activity. Use the no form of this command to disable debugging.
Page 943: Debug Platform Acl
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform acl debug platform acl Use the debug platform acl privileged EXEC command to enable debugging of the access control list (ACL) manager. Use the no form of this command to disable debugging.
Page 944 Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform acl Related Commands Command Description show debugging Displays information about the types of debugging that are enabled. Cisco Catalyst Blade Switch 3130 and 3032 for Dell Command Reference...
Page 945: Debug Platform Backup Interface
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform backup interface debug platform backup interface Use the debug platform backup interface privileged EXEC command to enable debugging of the Flex Links platform backup interface. Use the no form of this command to disable debugging.
Page 946: Debug Platform Cisp
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform cisp debug platform cisp Use the debug platform cisp global configuration command to enable platform-level debugging of a switch that has one or more Client Information Signalling Protocol (CISP)-enabled interfaces. Use the no form of this command to disable debugging.
Page 947: Debug Platform Cli-Redirection Main
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform cli-redirection main debug platform cli-redirection main Use the debug platform cli-redirection main privileged EXEC command to enable debugging of the main (important) command-line interface (CLI) redirection events. Use the no form of this command to disable debugging.
Page 948: Debug Platform Configuration
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform configuration debug platform configuration Use the debug platform configuration privileged EXEC command to enable debugging of configuration file activity across the stack. Use the no form of this command to disable debugging.
Page 949: Debug Platform Cpu-Queues
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform cpu-queues debug platform cpu-queues Use the debug platform cpu-queues privileged EXEC command to enable debugging of platform central processing unit (CPU) receive queues. Use the no form of this command to disable debugging.
Page 950 Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform cpu-queues Usage Guidelines The undebug platform cpu-queues command is the same as the no debug platform cpu-queues command. On a stacking-capable switch, when you enable debugging, it is enabled only on the stack master. To enable debugging on a stack member, you can start a session from the stack master by using the session switch-number privileged EXEC command.
Page 951: Debug Platform Device-Manager
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform device-manager debug platform device-manager Use the debug platform device-manager privileged EXEC command to enable debugging of the platform-dependent device manager. Use the no form of this command to disable debugging.
Page 952: Debug Platform Dot1X
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform dot1x debug platform dot1x Use the debug platform dot1x privileged EXEC command to enable debugging of IEEE 802.1x events. On stacking-capable switches, this command enables debugging of stack-related IEEE 802.1x events.
Page 953: Debug Platform Etherchannel
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform etherchannel debug platform etherchannel Use the debug platform etherchannel privileged EXEC command to enable debugging of platform-dependent EtherChannel events. Use the no form of this command to disable debugging.
Page 954: Debug Platform Fallback-Bridging
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform fallback-bridging debug platform fallback-bridging Use the debug platform fallback-bridging privileged EXEC command to enable debugging of the platform-dependent fallback bridging manager. Use the no form of this command to disable debugging.
Page 955: Debug Platform Ip Arp Inspection
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform ip arp inspection debug platform ip arp inspection Use the debug platform ip arp inspection privileged EXEC command to debug dynamic Address Resolution Protocol (ARP) inspection events. Use the no form of this command to disable debugging.
Page 956: Debug Platform Ip Dhcp
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform ip dhcp debug platform ip dhcp Use the debug platform ip dhcp privileged EXEC command to debug DHCP events. Use the no form of this command to disable debugging.
Page 957: Debug Platform Ip Igmp Snooping
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform ip igmp snooping debug platform ip igmp snooping Use the debug platform ip igmp snooping privileged EXEC command to enable debugging of platform-dependent Internet Group Management Protocol (IGMP) snooping. Use the no form of this command to disable debugging.
Page 958 Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform ip igmp snooping rpc [cfg | l3mm | misc Display IGMP snooping remote procedure call (RPC) event debug messages. | vlan] The keywords have these meanings: cfg—(Optional) Display IGMP snooping RPC debug messages.
Page 959: Debug Platform Ip Multicast
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform ip multicast debug platform ip multicast Use the debug platform ip multicast privileged EXEC command to enable debugging of IP multicast routing. Use the no form of this command to disable debugging.
Page 960 Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform ip multicast Usage Guidelines The undebug platform ip multicast command is the same as the no debug platform ip multicast command. On a stacking-capable switch, when you enable debugging, it is enabled only on the stack master. To enable debugging on a stack member, you can start a session from the stack master by using the session switch-number privileged EXEC command.
Page 961: Debug Platform Ip Unicast
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform ip unicast debug platform ip unicast Use the debug platform ip unicast privileged EXEC command to enable debugging of platform-dependent IP unicast routing. Use the no form of this command to disable debugging.
Page 962 Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform ip unicast Command History Release Modification 12.2(40)EX1 This command was introduced. Usage Guidelines The undebug platform ip unicast command is the same as the no debug platform ip unicast command.
Page 963: Debug Platform Ip Wccp
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform ip wccp debug platform ip wccp Use the debug platform ip wccp privileged EXEC command to enable debugging of Web Cache Communication Protocol (WCCP). Use the no form of this command to disable debugging.
Page 964: Debug Platform Ipc
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform ipc debug platform ipc Use the debug platform ipc privileged EXEC command to enable debugging of the platform-dependent Interprocess Communication (IPC) Protocol. Use the no form of this command to disable debugging.
Page 965: Debug Platform Led
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform led debug platform led Use the debug platform led privileged EXEC command to enable debugging of light-emitting diode (LED) actions. Use the no form of this command to disable debugging.
Page 966: Debug Platform Matm
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform matm debug platform matm Use the debug platform matm privileged EXEC command to enable debugging of platform-dependent MAC address management. Use the no form of this command to disable debugging.
Page 967: Debug Platform Messaging Application
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform messaging application debug platform messaging application Use the debug platform messaging application privileged EXEC command to enable debugging of application messaging activity. Use the no form of this command to disable debugging.
Page 968: Debug Platform Phy
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform phy debug platform phy Use the debug platform phy privileged EXEC command to enable debugging of PHY driver information. Use the no form of this command to disable debugging.
Page 969 Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform phy Usage Guidelines The undebug platform phy command is the same as the no debug platform phy command. On a stacking-capable switch, when you enable debugging, it is enabled only on the stack master. To enable debugging on a stack member, you can start a session from the stack master by using the session switch-number privileged EXEC command.
Page 970: Debug Platform Pm
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform pm debug platform pm Use the debug platform pm privileged EXEC command to enable debugging of the platform-dependent port manager software module. Use the no form of this command to disable debugging.
Page 971 Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform pm stack-manager Display stack-manager related-events debug messages. This keyword is supported on the stacking-capable switches. sync Display operational synchronization and VLAN line-state event debug messages.
Page 972: Debug Platform Port-Asic
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform port-asic debug platform port-asic Use the debug platform port-asic privileged EXEC command to enable debugging of the port application-specific integrated circuit (ASIC) driver. Use the no form of this command to disable debugging.
Page 973: Debug Platform Port-Security
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform port-security debug platform port-security Use the debug platform port-security privileged EXEC command to enable debugging of platform-dependent port-security information. Use the no form of this command to disable debugging.
Page 974: Debug Platform Qos-Acl-Tcam
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform qos-acl-tcam debug platform qos-acl-tcam Use the debug platform qos-acl-tcam privileged EXEC command to enable debugging of the quality of service (QoS) and access control list (ACL) hardware memory manager software. Use the no form of this command to disable debugging.
Page 975: Debug Platform Remote-Commands
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform remote-commands debug platform remote-commands Use the debug platform remote-commands privileged EXEC command to enable debugging of remote commands. Use the no form of this command to disable debugging.
Page 976: Debug Platform Resource-Manager
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform resource-manager debug platform resource-manager Use the debug platform resource-manager privileged EXEC command to enable debugging of the resource manager software. Use the no form of this command to disable debugging.
Page 977: Debug Platform Snmp
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform snmp debug platform snmp Use the debug platform snmp privileged EXEC command to enable debugging of the platform-dependent Simple Network Management Protocol (SNMP) software. Use the no form of this command to disable debugging.
Page 978: Debug Platform Span
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform span debug platform span Use the debug platform span privileged EXEC command to enable debugging of the platform-dependent Switched Port Analyzer (SPAN) software. Use the no form of this command to disable debugging.
Page 979: Debug Platform Stack-Manager
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform stack-manager debug platform stack-manager Use the debug platform stack-manager privileged EXEC command to enable debugging of the stack manager software. Use the no form of this command to disable debugging.
Page 980: Debug Platform Supervisor-Asic
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform supervisor-asic debug platform supervisor-asic Use the debug platform supervisor-asic privileged EXEC command to enable debugging of the supervisor application-specific integrated circuit (ASIC). Use the no form of this command to disable debugging.
Page 981: Debug Platform Sw-Bridge
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform sw-bridge debug platform sw-bridge Use the debug platform sw-bridge privileged EXEC command to enable debugging of the software bridging function. Use the no form of this command to disable debugging.
Page 982: Debug Platform Tcam
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform tcam debug platform tcam Use the debug platform tcam privileged EXEC command to enable debugging of hardware memory access and lookups. Use the no form of this command to disable debugging.
Page 983 Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform tcam Syntax Description log l2 {acl {input | output} | Display Layer 2 field-based CAM look-up type debug messages. The local | qos} keywords have these meanings: acl {input | output}—Display input or output ACL look-up debug...
Page 984 Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform tcam Usage Guidelines The undebug platform tcam command is the same as the no debug platform tcam command. On a stacking-capable switch, when you enable debugging, it is enabled only on the stack master. To enable debugging on a stack member, you can start a session from the stack master by using the session switch-number privileged EXEC command.
Page 985: Debug Platform Udld
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform udld debug platform udld Use the debug platform udld privileged EXEC command to enable debugging of the platform-dependent UniDirectional Link Detection (UDLD) software. Use the no form of this command to disable debugging.
Page 986: Debug Platform Vlan
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug platform vlan debug platform vlan Use the debug platform vlan privileged EXEC command to enable debugging of the VLAN manager software. Use the no form of this command to disable debugging.
Page 987: Debug Pm
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug pm debug pm Use the debug pm privileged EXEC command to enable debugging of port manager (PM) activity. The port manager is a state machine that controls all the logical and physical interfaces. All features, such as VLANs, UniDirectional Link Detection (UDLD), and so forth, work with the port manager to provide switch functions.
Page 988 Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug pm Usage Guidelines The undebug pm command is the same as the no debug pm command. On a stacking-capable switch, when you enable debugging, it is enabled only on the stack master. To enable debugging on a stack member, you can start a session from the stack master by using the session switch-number privileged EXEC command.
Page 989: Debug Port-Security
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug port-security debug port-security Use the debug port-security privileged EXEC command to enable debugging of the allocation and states of the port security subsystem. Use the no form of this command to disable debugging.
Page 990: Debug Qos-Manager
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug qos-manager debug qos-manager Use the debug qos-manager privileged EXEC command to enable debugging of the quality of service (QoS) manager software. Use the no form of this command to disable debugging.
Page 991: Debug Spanning-Tree
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug spanning-tree debug spanning-tree Use the debug spanning-tree privileged EXEC command to enable debugging of spanning-tree activities. Use the no form of this command to disable debugging.
Page 992 Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug spanning-tree Command History Release Modification 12.2(40)EX1 This command was introduced. Usage Guidelines The undebug spanning-tree command is the same as the no debug spanning-tree command. On a stacking-capable switch, when you enable debugging, it is enabled only on the stack master. To enable debugging on a stack member, you can start a session from the stack master by using the session switch-number privileged EXEC command.
Page 993: Debug Spanning-Tree Backbonefast
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug spanning-tree backbonefast debug spanning-tree backbonefast Use the debug spanning-tree backbonefast privileged EXEC command to enable debugging of spanning-tree BackboneFast events. Use the no form of this command to disable debugging.
Page 994: Debug Spanning-Tree Bpdu
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug spanning-tree bpdu debug spanning-tree bpdu Use the debug spanning-tree bpdu privileged EXEC command to enable debugging of sent and received spanning-tree bridge protocol data units (BPDUs). Use the no form of this command to disable debugging.
Page 995: Debug Spanning-Tree Bpdu-Opt
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug spanning-tree bpdu-opt debug spanning-tree bpdu-opt Use the debug spanning-tree bpdu-opt privileged EXEC command to enable debugging of optimized spanning-tree bridge protocol data units (BPDUs) handling. Use the no form of this command to disable debugging.
Page 996: Debug Spanning-Tree Mstp
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug spanning-tree mstp debug spanning-tree mstp Use the debug spanning-tree mstp privileged EXEC command to enable debugging of the Multiple Spanning Tree Protocol (MSTP) software. Use the no form of this command to disable debugging.
Page 997 Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug spanning-tree mstp Usage Guidelines The undebug spanning-tree mstp command is the same as the no debug spanning-tree mstp command. On a stacking-capable switch, when you enable debugging, it is enabled only on the stack master. To enable debugging on a stack member, you can start a session from the stack master by using the session switch-number privileged EXEC command.
Page 998: Debug Spanning-Tree Switch
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug spanning-tree switch debug spanning-tree switch Use the debug spanning-tree switch privileged EXEC command to enable debugging of the software interface between the Spanning Tree Protocol (STP) software module and the port manager software module.
Page 999 Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug spanning-tree switch Usage Guidelines The undebug spanning-tree switch command is the same as the no debug spanning-tree switch command. On a stacking-capable switch, when you enable debugging, it is enabled only on the stack master. To enable debugging on a stack member, you can start a session from the stack master by using the session switch-number privileged EXEC command.
Page 1000: Debug Spanning-Tree Uplinkfast
Appendix B Cisco Catalyst Blade Switch 3130 and 3032 for Dell Debug Commands debug spanning-tree uplinkfast debug spanning-tree uplinkfast Use the debug spanning-tree uplinkfast privileged EXEC command to enable debugging of spanning-tree UplinkFast events. Use the no form of this command to disable debugging.

This manual is also suitable for:

Catalyst 3032

Dell Catalyst 3130 Command Reference Manual

CHAPTER 1 Using the Command-Line Interface

CHAPTER 2 Cisco Catalyst Blade Switch 3130 and 3032 for Dell Cisco IOS Commands

Class

This Command Has no Arguments or Keywords

Defaults no Default Is Defined

Delete

Dot1X

Dot1X Pae

Duplex

Command Show Energywise

Hw-Module

Ip Ssh

MDIX Auto

Mls Qos

Nmsp

Nsf

Police

Queue-Set

Reload

Session

Set

Setup

Show Boot

Show Cisp

Show Dtp

Show Eap

Show Env

Command Modes Privileged EXEC

Quick Links

Related Manuals for Dell Catalyst 3130

Summary of Contents for Dell Catalyst 3130