Advertisement
Before Starting
Tools You Will Need
For leveling
legs and Anti-Tip
Bracket:
Adjustable
wrench or channel lock pliers
5/16" Nutdriver
or Flat Head Screw Driver
•
Electric Drill & 1/8" Diameter
Drill Bit (5/32" Masonry
Drill Bit if installing in concrete)
For gas supply connection:
Pipe wrench
For burner
flame adjustment:
Phillips head _
and
blade-type
screwdrivers
For gas conversion
(LP/Propane
or Natural):
Open end wrench - 1/2"
Additional
Materials
You Will Need
Gas line shut-off
valve I_
Pipe joint sealant that resists action of LP/Propane
gas
A new flexible metal appliance conduit (112' NPT x 3/
4" or
1/2'
I,D.)
must
be design
certified
by CSA
International.
Because solid
pipe restricts moving
the
range we recommend
using a new flexible conduit
(4
to 5 foot length) for each new installation
and additional
reinstallations.
Always
use the (2) new flare union adapters
(112" NPT
x 3/4" or 1/2" I.D.) supplied
with
the
new
flexible
appliance
conduit for connection of the range.
Normal
Installation
Steps
1. Anti-Tip
Bracket
Installation
Instructions
Important
Safety
Warning
To reduce the risk of tipping of the range, the range must
be secu red to the floor by properly
installed anti-tip bracket
and screws packed with the range. Failure to install
the
anti-tip bracket will allow the range to tip over if excessive
weight
is placed on an open door or if a child climbs upon
it. Serious injury
might result from
spilled
hot liquids
or
from the range itself.
If range is ever moved to a different location, the anti-tip
brackets must also be moved and installed with the range.
Instructions are provided for installation in wood or cement
fastened to either the floor or wall. When installed to the
wall, make sure that screws completely penetrate dry wall
and are secured in wood or metal. When fastening to the
floor or wall, be sure that screws do not penetrate electrical
wiring or plumbing.
A.
B,
3
Locate the Bracket Using the Template-
(Bracket may
be located on either the left or right side of the range.
Use the information
below to locate the bracket
if
template is not available).
Mark the floor or wall where
left or right side of the range will be located.
If rear of
range is against the wall or no further than 1-1/4" from
wall when
installed, you may use the wall or floor
mount method.
If molding
is installed and does not
allow the bracket to fit flush against the wall, remove
molding
or mount
bracket to the floor. For wall mount,
locate the bracket
by placing
the back edge of the
template
against the rear wall and the side edge of
template on the mark made referencing the side of the
range. Place bracket
on top of template
and mark
location
of the screw holes in wall.
If rear of range is
further than 1-1/4" from the wall when installed, attach
bracket
to the floor.
For floor mount,
locate the
bracket by placing back edge of the template
where
the rear of the range will be located.
Mark the location
of the screw holes, shown
in template.
Drill Pilot Holes and Fasten Bracket - Drill a 1/8" pilot
hole where screws are to be located. If bracket is to be
mounted
to the wall, drill pilot hole at an approximate
20 ° downward
angle. If bracket is to be mounted
to
masonry or ceramic floors, drill a 5/32" pilot hole 1-3/
4' deep. The screws provided may be used in wood or
concrete material.
Use a 5/16' nut-driver or flat head
screwdriver to secure the bracket in place.
FASTEN BRACKET (WNJ. o n ng.oon_ MOUI_rnNG)
_I
1<--1-1/4" Max.
Leveling Leg _
h
,
' -
Floor Mount ._,v_
/--Anti-l"ip Bracket
FASTEN BRACKET (FLOOR M OUNTING ONLY)
Leveling Leg --
1-1/4"
Floor Mount
, Bracket
Advertisement
