INTRODUCTION Foreword We are proud to offer the Model G0631 79" x 28" Downdraft Table. This machine is part of a grow- ing Grizzly family of fine woodworking machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s com-...
Identification Figure 1. Identification, Model G0631. A. Left Panel B. Center Panels C. Downdraft Plates D. Right Panel E. ON/OFF Switch Dust Drawer G. Outlet Plates G0631 79" x 28" Downdraft Table...
Page 9
If normal safety precautions are overlooked or ignored, serious personal injury may occur. G0631 79" x 28" Downdraft Table 5. EMPTYING DUST DRAWER. ing dust from the dust drawers, wear a respi- rator and safety glasses.
DO NOT connect the machine to the power source until instructed to do so. Amperage Draw Each Model G0631 motor draws the following amps under maximum load: Motor Draw ... 12 Amps Circuit Recommendations...
Safety Glasses (for each person) ... 1 • Phillips Screwdriver #2 ... 1 The Model G0631 was carefully packed when it left our warehouse. If you discover the machine is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice.
⁄ " NOTICE SUFFOCATION HAZARD! Immediately discard all plas- tic bags and packing materi- als to eliminate choking/suf- focation hazards for children and animals. G0631 79" x 28" Downdraft Table...
Serious personal injury may occur if safe moving methods are not used. To be safe, get assistance and use power equipment to move the shipping crate and remove the machine from the crate. G0631 79" x 28" Downdraft Table...
1" Filter Airflow Figure 5. Filters installed in filter bay (one side shown). G0631 79" x 28" Downdraft Table Install the downdraft plates as shown in Figure 6, placing the thinner center down- draft plate in the middle. Figure 6. Installing downdraft plates.
Page 16
"-20 x the handles on the outlet plates at the rear of the downdraft table as shown in Figure 11. Figure 11. Outlet plate handles mounted. Left Panel ⁄ Phillips head screws, mount Screws Handle G0631 79" x 28" Downdraft Table...
Connect EACH motor to a dedicated 110V circuit (see CIRCUIT REQUIREMENTS, Page 8). G0631 79" x 28" Downdraft Table Flip both paddle switches up to turn the downdraft table ON. Make sure that your hand stays poised over the switches in case you need to quickly turn the machine OFF.
OMMEND that you read books, trade maga- zines, or get formal training before begin- ning any projects. Regardless of the con- tent in this section, Grizzly Industrial will not be held liable for accidents caused by lack of training. -16-...
H5916—60 Grit 10 Pack Sandpaper for H3120 H5917—120 Grit 10 Pack for H3120 H5918—180 Grit 10 Pack for H3120 H5919—240 Grit 10 Pack for H3120 G0631 79" x 28" Downdraft Table H4938—16" x 25" x 2" (0.3 Micron) Filter for G0631 Figure 17. Model H4938.
Page 20
Model H3633 protects against organic vapor, sulfur dioxide, hydrogen chloride and chlorine. Model H3635 protects against all particulate H1298 aerosols. H0736 Figure 20. Half-mask respirator and disposable cartridge filters. G0631 79" x 28" Downdraft Table...
Clean/vacuum dust buildup from inside cabi- net and off motors. Cleaning Cleaning the Model G0631 is relatively easy. Vacuum excess sawdust, and wipe off the remain- ing dust with a dry cloth. If any resin has built up, use a resin dissolving cleaner to remove it.
1. Adjust fan balance or replace fan. 2. Inspect/replace stripped or damaged bolts/nuts, and re-tighten with thread locking fluid. Possible Solution 1. Empty collection drawer. 2. Knock dust off filter. If this has no effect, replace with new filter unit. G0631 79" x 28" Downdraft Table...
Electrical Components Figure 21. Right Switch wiring. Figure 23. Wiring for both motors. Figure 22. Left motor wiring. Figure 24. Right Motor Wiring. -21- G0631 79" x 28" Downdraft Table...
PTLW01 PN07 P0631035 PW06 PLN02 P0631038 PB09M PN03M G0631 79" x 28" Downdraft Table DESCRIPTION FLAT WASHER #10 PHLP HD SCR 10-24 X 3/8 SMALL DUST COLLECTING PLATE BIG DUST COLLECTING PLATE MOTOR 110V, 1HP RUBBER PAD PHLP HD SCR 10-24 X 3/8...
MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels. G0631 79" x 28" Downdraft Table...
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.