Page 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.
ID label (see below). This information is required for us to provide proper tech support, and it helps us determine if updated documenta- tion is available for your machine. Manufacture Date Serial Number Model G0888 (Mfd. Since 01/19)
Inlet Grinder Coolant Cups Mounting Plate Auxiliary Electrical Outlet Dust Collection Drawer LED ON/OFF Switch Air Filter Drawer Motor ON/OFF Switch To reduce your risk of serious injury, read this entire manual BEFORE using machine. Model G0888 (Mfd. Since 01/19)
Machine Data Sheet Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0888 DELUXE BENCH GRINDING STATION Product Dimensions: Weight ................................... 218 lbs. Width (side-to-side) x Depth (front-to-back) x Height ..............24-1/2 x 30-1/2 x 63-1/2 in.
Page 7
Two Onboard 115V Power Receptacles for Connection to Bench Grinders Built-In Mobile Base for Easy Movement Removable Clean-Out Drawer 12" LED Work Light Two Stainless-Steel Coolant Cups Work Table Mounted on Rubber Feet for Reduced Vibration Model G0888 (Mfd. Since 01/19) Page 2 of 2 Model G0888...
Never operate under the influence of drugs or injury or blindness from flying particles. Everyday alcohol, when tired, or when distracted. eyeglasses are NOT approved safety glasses. Model G0888 (Mfd. Since 01/19)
Page 9
Make sure they are properly installed, you experience difficulties performing the intend- undamaged, and working correctly BEFORE ed operation, stop using the machine! Contact our operating machine. Technical Support at (570) 546-9663. Model G0888 (Mfd. Since 01/19)
NEVER use near chemical fumes or within an Duct must be disconnected before service. Never enclosed spray booth. operate machine with filters or covers removed. Model G0888 (Mfd. Since 01/19)
Page 12
Two-prong outlets do not meet the grounding requirements for this machine. Do not modify or use an adapter on the plug provided—if it will not fit the outlet, have a qualified electrician install the proper outlet with a verified ground. -10- Model G0888 (Mfd. Since 01/19)
(or other have resolved any issues between Grizzly or the lifting equipment) rated for shipping agent. You MUST have the original pack- weight of this machine.
If you cannot find an item on this list, care- fully check around/inside the machine and packaging materials. Often, these items get lost in packaging materials while unpack- Figure 4. Fastener inventory. ing or they are pre-installed at the factory. -12- Model G0888 (Mfd. Since 01/19)
Only install in an Shadows, glare, or strobe effects that may distract access restricted location. or impede the operator must be eliminated. 30½" Min. 30" for Maintenance 24½" = Electrical Connection 42" Figure 5. Minimum working clearances. -14- Model G0888 (Mfd. Since 01/19)
⁄ "-20 x ⁄ " hex bolts and (8) ⁄ " flat washers (see Figure 7). Figure 9. Work light support mounted to dust inlet. Figure 7. Swivel casters attached to rear of stand. -15- Model G0888 (Mfd. Since 01/19)
Page 18
(see Figure 12). Power Support Hex Bolts Cord Grinder w/Washers Mounting Plate (1 of 4) Figure 10. Work light mounted to support. Rubber Feet (2 of 4) Figure 12. Grinder mounting plate installed. -16- Model G0888 (Mfd. Since 01/19)
Dust Hose Attach dust hoses to grinder and secure with (1 of 2) hose clamps (see Figure 13). Fasteners Mounting Plate Figure 13. Example of grinder fastened to mounting plate. -17- Model G0888 (Mfd. Since 01/19)
The motor should run smoothly and without any padlock used to lock the switch, test unusual problems or noises. the switch after installation to ensure that it is properly disabled. Figure 16. Lock shaft requirements. -18- Model G0888 (Mfd. Since 01/19)
When operation is complete, turn grinder ects. Regardless of the content in this sec- OFF, then turn grinding station OFF. tion, Grizzly Industrial will not be held liable for accidents caused by lack of training. -19- Model G0888 (Mfd. Since 01/19)
H3631 Figure 18. Half-mask respirator and disposable cartridge filters. T31561—Replacement Air Filter This pleated air filter is aluminum-framed and fits directly on the G0888 Deluxe Bench Grinding Station. Figure 20. Cowhide leather gloves. www.grizzly.com 1-800-523-4777 order online at...
Page 23
Cast iron handle provides employees operate for hours at a time. stabilizing mass for better control. H4978 T20446 H4979 Figure 22. Rotary-type dressing tools. Figure 24. Hearing protection. www.grizzly.com 1-800-523-4777 order online at or call -21- Model G0888 (Mfd. Since 01/19)
Lay out clean cardboard sheet, then gently lay machine on its back. Remove (12) hex bolts and washers from motor mounting plate (see Figure 27). Motor Mounting Plate Figure 27. Hex bolts and washers secure motor/ impeller assembly to stand. -24- Model G0888 (Mfd. Since 01/19)
(3) screws removed in Step 2. Re-attach dust hoses to inlet and secure with hose clamps. Position work light in clamps and tighten thumb screws to secure. -25- Model G0888 (Mfd. Since 01/19)
2. Clean filter; replace with new filter if performance collect dust does not improve (Page 23). or chips; poor 3. Clean dust inlet (Page 25). 3. Dust inlet is dirty/clogged. performance. 4. Leak in dust hose connection. 4. Seal leak. -26- Model G0888 (Mfd. Since 01/19)
Technical Support at (570) 546-9663. The photos and diagrams included in this section are best viewed in color. You can view these pages in color at www.grizzly.com. -27- Model G0888 (Mfd. Since 01/19)
SECTION 9: PARTS We do our best to stock replacement parts when possible, but we cannot guarantee that all parts shown are available for purchase. Call (800) 523-4777 or visit www.grizzly.com/parts to check for availability. Main 24-1 53-1 53-1 70-1...
Page 33
DUST HOSE 2-1/2" X 11" (RUBBER) P0888086 CORRUGATED SLEEVE 5' P0888048 HOSE CLAMP 2-1/2" P0888087 CUP HOLDER (RUBBER) P0888049 HOSE CLAMP 2-1/2" P0888088 CABLE TIE 6" BUY PARTS ONLINE AT GRIZZLY.COM! -31- Model G0888 (Mfd. Since 01/19) Scan QR code to visit our Parts Store.
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com. BUY PARTS ONLINE AT GRIZZLY.COM! -32- Model G0888 (Mfd.
WARRANTY & RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.