Before using your tumble dryer, please read this manual carefully and keep it for future reference. Tumble Dryer OWNER’S MANUAL BCD71 Read This Manual Inside you will find many helpful hints on how to use and maintain your tumble dryer properly. Just a little...
Page 2
Dear Customer, Congratulations on purchasing your new product from Think Appliances. To register your parts and labour warranty (some conditions apply please refer to your warranty card for more details) please contact out Customer Care team on: 1800 444 357 Our Customer Care centre is there to ensure you get the most out of your appliance.
Safety information Dry Care Symbols Please pay attention to use the drying machine if the materials of your clothes can not be dried by it or contain the symbols as follows: Normal Not tumble dry normal Do not dry Drip dry In the shade Line dry / hang to dry Dry flat...
Safety information Injury danger 1.Please do not disassemble and install the dryer under no instruction or supervision. 2.Please do not stack this dryer on washing machine without stacking kits. 3.Please do not lean on the opened door of the dryer. 4.Please do not put any pyrotoxin on the dryer, such as the candle, electric cooker.
Installation Installation Position 1.Please install the dryer on solid and flat ground. 2.Please do not place the dryer on the slope, soft carpet or wooden floor. 3.Please do not install the dryer outdoors, to prevent the dryer from being frozen to damage of machine parts Level Adjusting If the floor is obviously uneven, it needs to be adjusted.
Part Description Part Description Control Panel Container Door Power Cord Lint filter Maintenance flap Condenser Accessories The following parts are optional for specific models. If your dryer has following parts, please install them following the instruction below . Condensing drain hose(optional) Hose holder(optional)
Part Description 200cm Quick start 1. Open the door and 9.Unplug the power cord load the laundry 8.Turn the knob to “OFF” 2 Close the machine door 7. Clean the lint filter and 3 Plug the power cord empty container 6.
Attention & Advice Attention Before the first cycle, the dust and grease may remain in this dryer during the period of manufacture and transportation, to avoid contaminating your clothes, please follow these steps: a)Put some clean rags into the drum. b)Plug the power.
Operation Instruction Programme selector 1.Rotate the programme knob to select the desired programme. 【 】 【 】 【 】 2.Select the Delay , Anti-Crease or Gentle functions for additional option. 【 】 3.Press the Start/Pause key. The Drying procedure stops The buzzer will prompt from the dryer when finishing the cycle.
Specialty drying function Specialty drying function 1. Instruction of the moisture sensor This function can automatically sense the moisture of clothes, and will automatically adjust the time of drying procedure according to how much clothes you put into the dryer. This function will automatically activate during the drying procedure except the “Warm”...
Page 14
Special drying function icon and no key can effect to the dryer. Under the start state of the child lock button, the【Delay/Light】and 【Anti-Crease】buttons shall be pressed at the same time for over 3 seconds to release the child lock function. 5.
Cleaning and routine maintenance Clean the lint filter Leave the dryer to cool down. 1.Open the machine door. 2.Take out the lint filter, pull upward to take it out. 3.Clean the lint filter; wipe off the scrap threads accumulated on the lint filter. 4.Reinstall the lint filter.
Alarm function Alarm function Alarm Problem Alarm Reason Buzzer Alarm Release Water tank full or pump Check the water tank and pump. “ ”Is flashing error “ ”Is flashing Air flow block Check the filter and the air folw Heater problem Check the heater and the thermostat “...
Precautions Precautions Repairs may be carried out by customer service of authorised technicians only! Before you call customer service, please check whether you can correct the fault yourself. A technician will charge you for advice, even during the warranty period. Problem Solution The mains plug is inserted.