Deleting, Replacing, Or Editing Wireless Keys - Honeywell ADEMCO 6150RF Installation And Setup Manual

Step
Wireless Key Function Chart
6.
Function
(Cont'd)
Disarming
Arming Away
Arming Stay
Arming Maximum (Away Instant)
Arming Instant
Panic Alarm
Produces type of alarm [* & #]
programmed in control panel.
Manually Start a Relay Action
Manually Stop a Relay Action
Activate Relay as Programmed in
Control
Activate Relay as Programmed in
Control
Activate Access Control Relay for
Partition
n = Device Number programmed in panel to be controlled
Press the [✻] key.
Repeat step 6 for the rest of the loops of the wireless key.
7.
8. To program a button on the wireless key to control the on-board
relay, enter [5] (On-Board Relay Assignment).
9. Enter the loop number of the wireless key (1-4). Enter the relay
action (0 = no action; 1 = relay off; 2 = relay on; 3 = relay toggles on
and off; 4 = relay closes for 2 seconds).
Note: The relay action must be "0" for UL installations.
Press the [✻] key.
Repeat step 9 for the rest of the loops.
10.
When all loops have been programmed for the wireless key, press the
11.
[✻] key.
12. The 6150RF automatically displays the next available device number
(one that does not have a serial number).
If you want to program additional wireless keys, repeat steps 3
through 10. Otherwise, press the [#] key. This takes you back to the
main display, which alternately flashes "oo" and "- -."
Enter [0] (High Security Mode). To put the system into High-Security
13.
mode, enter [1]. Enter [0] to disable.
Press [✻] to exit the 6150RF Program mode.
14.
Note: Upon exiting the Program mode, the 6150RF alternately flashes "Ad," the 2-digit keypad address, and the 2-digit receiver
address. If either of these is incorrect, repeat steps 1 through 3 in the Programming for an Installation Without Local Wireless
Keys section.

Deleting, Replacing, or Editing Wireless Keys

Use the following procedure to delete, replace, or change any of the programming for a wireless key.
Step
1. Enter the Program mode by pressing the [1] and [3] keys
simultaneously for a few seconds within 30 seconds after applying
power.
Enter [5] (Wireless Key Editing). Enter the device number for the
2.
wireless key you want to edit. This must be a device that has its
serial number programmed in the 6150RF already.
To delete the serial number, press [✻], then press [9], and press [✻]
again.
To exit without deleting the serial number, press the [#] key.
Press the [✻] key to continue.
Action
Entry
1
2
3
4
7
# + 99
# + 7 (VISTA-10SE, VIA-30PSE)
# + 7 + n (VISTA-10P, VISTA-15P,
VISTA-20P, VISTA-20SE(HW))
# + 8 (VISTA-10SE, VIA-30PSE)
# + 8 + n (VISTA-10P, VISTA-15P,
VISTA-20P, VISTA-20SE(HW)
# + 71 (VISTA-40, VISTA-50P,
VISTA-128B)
# + 72 (VISTA-40, VISTA-50P,
VISTA-128B)
0 (VISTA-40, VISTA-50P, VISTA-
128B)
Action
- 6 -
Display
Default Loop Functions
Loop 4
Arm STAY
5 8 0 4
Loop 3
Arm AWAY
• •
• •
• •
• • •
• • • •
• • • •
•
•
5 8 0 4 B D / 5 8 0 4 B DV
NOTE: If the loop is defaulted with a function (e.g.,
Arm, Disarm) and also is assigned to activate
the on-board relay, the system performs
BOTH functions.
Flashes "o-."
Flashing "o" and the loop number.
Once the action is entered, displays "o" and
alternately flashes the loop number and the relay
action.
Flashes "d" followed by the device number.
Flashes "En" and "0" alternately OR "En" and
"1" if the keypad is in high-security mode
Display
Alternately flashes "oo" and two dashes.
Flashes the device number and a hyphen.
Once the device number is entered, alternately
flashes "d" with the device number; and the serial
number.
Loop 3
Arm AWAY
Loop 2
Disarm
Loop 1
Close on-board relay
for 2 seconds
Loop 2
Disarm
Loop 4
Arm STAY
Loop 1
Close on-board relay
for 2 seconds
SET
HOUSE
CODE