Philips CMP200 User Manual

Register your product and get support at
www.philips.com/welcome
A
CMP200
B
EN User manual
RU Руководство пользователя
2. Your car power amplifier
English
Congratulations on your purchase, and welcome to Philips! To fully
1. Important
benefit from the support that Philips offers, register your product at
www.philips.com/welcome.
Safety Introduction
With the amplifier, you can enjoy high quality sound performance with
• Read and understand all instructions before you use the apparatus. If damage
powerful bass and beats.
is caused by failure to follow instructions, the warranty does not apply.
• This unit is designed for negative ground (earth) 12 V DC operation only.
• Use only the supplied mounting hardware for a safe and secure installation. What's in the box
• Do not connect any active speakers (with built-in amplifier) to the speaker
Check and identify the contents of your package:
terminals of the unit. Doing so may damage the active speakers.
• To ensure safe driving, adjust the volume to a safe and comfortable level. Amplifier
a
• To avoid short circuit, do not expose the apparatus to rain or water.
b Screw_4x25mm (x4)
• Never expose the apparatus to direct sunlight, naked flames or heat.
• Clean the apparatus with soft, damp cloth. Never use substances such as
c Fuse (x2)
alcohol, chemicals or household cleaners on the apparatus.
d Hi input connector (x1)
Notice
Overview of the main unit
Environmental information
OUTPUT L/R
a
All unnecessary packaging has been omitted. We have tried to make the
Connect additional amplifier for additional speakers.
•
packaging easy to separate into three materials: cardboard (box), polystyrene
b INPUT L/R
foam (buffer) and polyethylene (bags, protective foam sheet.)
Your system consists of materials which can be recycled and reused if • Connect car audio with RCA cable.
disassembled by a specialized company. Please observe the local regulations
HI INPUT
c
regarding the disposal of packaging materials, exhausted batteries and old
• Connect car audio with the supplied high input connector.
equipment.
d INPUT LEVEL
Any changes or modifications made to this device that are not expressly Adjust input level (0.3V to 6V).
•
approved by Philips Consumer Lifestyle may void the user's authority to
PROTECT
e
operate the equipment.
• Light in red when the PROTECTOR is activated.
POWER
f
2009 © Koninklijke Philips Electronics N.V. All rights reserved.
Specifications are subject to change without notice. Trademarks are the property of Koninklijke Philips • Light in blue when power is turned on.
Electronics N.V. or their respective owners. Philips reserves the right to change products at any time
FREQ
without being obliged to adjust earlier supplies accordingly. g
• Adjust frequency of HPF or LPF from 30Hz to 400Hz.
C
a b
c d
D
a
i h g fe d c b a
b
L R
j k l
HPF/OFF/LPF
h
• Select High-pass-filter (HPF), Low-pass-filter(LPF) or OFF (flat)
mode.
BASS BOOST
i
• Boost the frequencies at around 45Hz to a maximum of 12dB.
j POWER (GND/REM/+12V)
• Connect +12V DC power cable, ground wire and remote wire.
Fuse: 30Ax2
k
SPEAKER OUTPUT
l
• Connect to speakers or subwoofers.
A
3. Installation
Installation
C
You can mount the amplifier either under a seat or on the rear tray.
Note
• To avoid interference, do not place the amplifier too close to the car audio or
B
antenna.
• The supplied mounting screws are 25mm long. Make sure that the mounting
board is thicker than 25mm.
1
Place the unit on the location for installation.
2
Mark the positions of the four screw holes.
3 Drill the holes with driller of approximately 4mm in diameter.
4
Mount the unit with the supplied screws.
Connect speakers
Note
• Use speakers with an impedance of 2 to 8 ohm (4 to 8 ohm when used as a
bridged amplifier).
• Match the "left", "right", "+" and "-" terminals correctly. Revised polarity may
degrade sound quality.
c
4 ohm speaker
Динамик 4 Ом
E
a
Left speaker
Л
L R Right speaker
П а
4 ohm speaker
Динамик 4 Ом
L R
White
Б
4 ohm speaker 4 ohm speaker Б
White / Black
Динамик 4 Ом Динамик 4 Ом
Option 1: Mono bridged mode: connect 1 speaker
Option 2: Stereo mode: connect 2 speakers
Option 3: Tri-mode: connect 3 speakers
Connect car audio
E
Option 1: High level input connection
Connect the amplifier to your car audio with the supplied High level
input connector.
Option 2: Line input connection
b
Connect the amplifier to the car audio with a RCA cable (not supplied).
Option 3: Line output connection
c
Connect the amplifier to another amplifier.
Connect power
F
1
Make the power connection as illustrated below:
• Connect the ground wire from the car to the
Connect the remote wire from the car audio to the
•
√ With this connection, you can turn on/off the amplifier
with the car audio.
• Connect the power wire from the car battery to the
socket.
Tip
• If your car audio does not have remote output, connect the remote input
terminal (REM) to the accessory power supply.
D
4. Use your power amplifier
Select crossover frequency mode
You can select crossover frequency mode as below:
b
L R
4 ohm speaker
Динамик 4 Ом
8 ohm speaker
Динамик 8 Ом
c
Car audio unit
А
а
Grey
С
/ С /
Grey / Black
a HPF (high-pass-filter) mode Select this mode when mid-range speakers and
tweeters are connected for high frequency output.
b
LPF (Low-pass-filter) mode Select this mode when woofer and subwoofer is
c
connected for low frequency output.
OFF (flat) mode Select this mode when tri-mode speaker connection
is used.
1
Slide HPF/OFF/LPF to the selected positon.
a
Adjust frequency
You can adjust frequency of HPF or LPF from 30HZ to 400Hz.
Note
• When the HPF/OFF/LPF switch is set at OFF position, the frequency adjustment
does not work.
1
Rotate FREQ to select frequency.
Adjust input level
GND socket.
REM socket.
You can adjust the input voltage from 0.3V to 6V.
1
Rotate INPUT LEVEL to adjust input voltage.
+12V
Adjust bass boost
You can punch extra bass for 0 to 12dB.
1
Rotate BASS BOOST to punch for extra bass.
About the protector indicator
The amplifier has a built-in protection circuit to protect the transistors
and speakers when:
The unit is overheated. Or
•
• A DC current is generated. Or
• The battery voltage is over low or over high. Or
• The speaker terminals are short circuited.
F
Car audio unit
А
L R
а
to a metal point of the car
LINE OUT
К а а а
Л
less than 450 mm (18 in)
Remote output М 450 (18
В а ДУ
Car audio unit
А
Fuse (60 A)
а
П а а (60 А)
+12 V car battery
А а
G
When the PROTECT indicator lights up in red, the unit shuts down
automatically. If this happens, please:
1 Take out the disc or tape and turn off the car audio.
2 Check the cause of the malfunction (see above).
3
If the amplifier has overheated, wait until the unit cools down
before use.
Replace fuse
G
If there is no power, the fuse may be damaged and need to be replaced.
1
Pull out the damaged fuse.
2
Replace the fuse with the supplied fuses or to buy two fuses
that matches the voltage of the damaged fuse (30Ax2).
If the fuse gets damaged immediately after it has been replaced, there
may be an internal malfunction. In such case, consult your Philips dealer.
5. Product information
Note
• Product information is subject to change without prior notice.
Power Output (RMS)
- 4 ohm 125Wx2
- 4 ohm (bridged) 380Wx1
- 2 ohm 190Wx2
Total harmonic distortion
0.01%
Signal to noise ratio 106dB
Channel separation 50dB
Frequency response 5-100kHz
Input sensitivity 300mV-6V
Input impedance 22k ohm
Fuse rating 30Ax2
Dimensions (DxWxH) 54.4x336.5x240.2mm
)
+12 В