GE Profile Advantium PSB9100SFSS Dimension Manual

PSB9100SF
Suitable
bracing
GE Profile Series Advantium
™
21-5/8"
to support
over centerline
runners
of cabinet
(Must support 130 lbs.)
Advantium wall oven/GE Profile
dimensions and cabinet installation information (in inches)
Note: Cabinets
installed adjacent
to wall ovens must
have an adhesion
spec of at least a
194°F temperature
rating.
19-1/8"
Note: 2" minimum
between cutouts
when installed
above warming
drawer or single
wall oven.
Installation
Information:
Before installing,
consult installation
instructions packed
with product for current
dimensional data.
Note: Advantium wallovens can be installed below GE/GE Profile Series non-down-
draft gas and electric cooktops. It CANNOT be installed below induction or
Monogram (2GU3841385) gas cooktops.
Note: Advantium wall oven comes with two lower trim pieces. One is for use above
36-inch height installations and one is for use below 36-inch installations. Use of
the accessory drawer will replace the bottom trim piece for applicable installations.
Please see installation instructions for full details.
solid floor
26-3/4"
120V - 27 in. Wall Oven
®
A=Allow 1" overlap of oven over bottom edge of cutout.
B=Allow 11/16"-3/4" for overlap of oven over side edges of cutout.
Series cooking tower
™
4-3/16"
Cabinet width
A
B
21-1/2"
To back
of Control
26-3/4"
A
B
Conduit
(46" long)
Suitable
bracing
to support
runners
For answers to your Monogram
appliance questions, visit our website at
geappliances.com or call GE Answer Center
service, 800.626.2000.
Required
cutout location
36-3/4"
minimum
from floor
cabinet
width
Advantium Wall Oven Dimensions (in inches)and
Cabinet Installation (in inches)
Note: Cabinets installed adjacent
to wall ovens must have an adhesion
spec of at least 194° F temperature rating.
Junction box location (240-volt models only)
3" MIN between cutouts
recommended—2" MIN required
C L
2x4's or
equivalent
Construct Solid Bottom
solid floor
MIN 3/8" Plywood Supported by
2 x 4 or 1 x 2 Runners, all Four Sides.
(Must Support 150 lbs. for Advantium)
(Must Support 200 lbs. for Wall Oven)
9-1/4" cutout height
28-1/2" cutout width
2" MIN between cutouts
21-5/8"
over centerline
of cabinet
(Must support 130 lbs.)
1" Min. above toekick or adjust
to oven installation height
Cabinet width
19-1/8"
21-1/2"
To back
Suitable
of Control
bracing
26-3/4"
to support
runners
or GE
® ®
Conduit
(46" long)
®
3/8" Plywood
Supported by
2 x 4 or 1 x 2
Runners, all
Four Sides.
(Must Support
150 lbs.)
25-1/4"
Cutout width
21-1/2"
To Back of Control
A
Conduit
19-1/8"
(48-1/2"
Advantium Wall Oven Dimensions (in inches)and
long)
Cabinet Installation (in inches)
Note: Cabinets installed adjacent
26-3/4"
to wall ovens must have an adhesion
spec of at least 194° F temperature rating.
cabinet
width
A=Allow 1" overlap of oven over bottom edge of cutout.
B=Allow 11/16"-3/4" for overlap of oven over side edges of cutout.
C L
2x4's or
4-3/16"
equivalent
solid floor
Junction box location
A
B
3" MIN between cutouts
recommended—2" MIN required
21-5/8"
over centerline
A
B
of cabinet
Construct Solid Bottom
MIN 3/8" Plywood Supported by
(Must support 130 lbs.)
2 x 4 or 1 x 2 Runners, all Four Sides.
(Must Support 150 lbs. for Advantium)
Specification Revised 7/13
(Must Support 200 lbs. for Wall Oven)
9-1/4" cutout height
28-1/2" cutout width
4-3/16"
23-1/2"
Cutout depth
Junction box
location
(240-volt
models only)
B
17-1/2"
Cutout height
Construct Solid
Bottom Min.
Cutout widt
3/8" Plywood
Required
Supported by
cutout location
2 x 4 or 1 x 2
36-3/4"
Runners, all
minimum
Four Sides.
from floor
21-1/2"
(Must Support
To Back of Control
150 lbs.)
Conduit
19-1/8"
(48-1/2"
26-3/4"
(240-volt models only)
Listed by
Underwriters
Laboratories
A=Allow 1" overlap of oven over b
B=Allow 11/16"-3/4" for overlap o
240411
25-1/4"
A
long)
cabinet
width