Connecting The Units; Connecting The Power Cord; When Connecting To Separately Sold Power Amp - Pioneer AVH-P6800DVD Installation Manual

Connecting the Units

Connecting the Units

Connecting the power cord

Note:
IP-BUS input
16 cm
Depending on the kind of vehicle, the
function of 3* and 5* may be different.
In this case, be sure to connect 2* to 5*
Violet/white
and 4* to 3*.
Refer to Fig. 4.
1*
3* 2* This product
Blue
Multi-CD player
(sold separately)
5* 4* IP-BUS cable
Connect leads of the same
C a p ( 1 * ) color to each other.
When not using this terminal,
Fuse holder (10 A)
do not remove the cap.
Yellow (3*) Yellow (2*)
Back-up To terminal always supplied
(or accessory) with power regardless of
ignition switch position.
Fuse resistor
Red (5*) Red (4*)
Accessory To electric terminal controlled
(or back-up) by ignition switch (12 V DC)
ON/OFF.
Orange/white
To lighting switch terminal
Black (ground)
To vehicle (metal) body.
ISO connector
Note:
Speaker leads
In some vehicles, the ISO connector
White: Front left +
may be divided into two. In this case,
White/black: Front left ≠
be sure to connect to both connectors.
Front right +
Gray:
Gray/black: Front right ≠
When you connect the separately sold multi-channel
Green: Rear left + or Subwoofer +
processor (DEQ-P6600) to this unit, do not
Green/black: Rear left ≠ or Subwoofer ≠
connect anything to the speaker leads and system
Rear right + or Subwoofer +
Violet:
remote control (blue/white).
Violet/black: Rear right ≠ or Subwoofer ≠
AUX input jack
20 cm
Antenna cable
15 cm
Yellow/black
If you use a cellular telephone, connect it via the
Audio Mute lead on the cellular telephone. If not,
keep the Audio Mute lead free of any connections.
Connection method
1. Clamp the lead. 2. Clamp firmly firmly f with
needle-nosed
pliers.
Note:
• The position of the parking brake switch depends
on the vehicle model. For details, consult the
vehicle Owner's Manual or dealer.
Light green
Used to detect the ON/OFF status of the parking brake.
This lead must be connected to the power supply side of the parking
brake switch.
Blue/white
To system control terminal of the power amp
Power supply side
(max. 300 mA 12 V DC).
Ground side
Blue/white (6*) Blue/white (7*)
To Auto-antenna relay control terminal
(max. 300 mA 12 V DC).
The pin position of the ISO connector will differ
depending on the type of vehicle. Connect 6* and
7* when Pin 5 is an antenna control type. In
another type of vehicle, never connect 6* and 7*.

When connecting to separately sold power amp

This product
Blue/white
To system control terminal of the power amp
(max. 300 mA 12 V DC).
When you connect the separately sold
multi-channel processor (e.g. DEQ-P6600)
to this unit, do not connect anything to the
speaker leads and system remote control
(blue/white).
Note :
Parking brake
When you connect the multi-channel processor
switch
to this unit, a separately sold power amp must
be connected to the multi-channel processor.
Note :
Change the initial setting of this product
(refer to the Operation Manual).
The subwoofer output of this unit is monaural.
Fig. 2
Subwoofer output
or non fading output
(SUBWOOFER OUTPUT or
NON-FADING OUTPUT)
23cm
Front output
(FRONT OUTPUT)
15cm
Connecting cords
with RCA pin plugs
Rear output
(sold separately)
(REAR OUTPUT)
15cm
System remote control
Blue/white
+
Front speaker
≠
+
Rear speaker
≠
Left
+
Subwoofer
≠
<ENGLISH> <ENGLISH>
Power amp
(sold separately)
Power amp
(sold separately)
Power amp
(sold separately)
+
Front speaker
≠
+
Rear speaker
≠
Right
+
Subwoofer
≠
Perform these connections when using the
optional amplifier.
Fig. 3