Advertisement
Quick Links
NIGHT VISION IR DOME CAMERA
VDC-350PIV-V
VDC-350NIV-V
User Guide
1.PLASTIC ANCHOR: insert into the SCREW hole of the
installation location(to strengthen the installation).
2.ASSY SCREW TAPPING：use for installation on the
ceiling or wall.
3. L WRENCH：for body cover and camera base
assembly.
6. Installation
1.Drill a hole in the place where the camera is
installed. Completely insert the PLASTIC ANCHOR
provided. then lead the power and video cables pass
through the hole.
2.Disassemble the body cover and camera base
from dome camera .
3.Fasten the dome camera base on the wall or the
ceiling.
Wall
Ceiling
NIGHT VISION IR DOME CAMERA
1. Features
The camera adopts advanced Digital Signal
Processor(DSP) technology,Enhances picture
quality greatly to horizontal resolution of
540TVL. Provides clearer and more vivid image.
Latest DSP controls for BLC, white balance,
and gain control.
Integrated efficient powerful IR LED array can
capture high-resolution picture even in complete
darkness. Night view distance up to10~15m.
Light control design. Auto light detection for IR
LED switch control.
The camera is equipped with a Vari-focal lens,
f=4~9mm.
Manual pan /tilt mechanism,3-Axis Rotation.
Accept 12VDC power supply.
Anda polygon dome shield, which can bear up to
120 pounds impact and won't be destroyed. It
has excellent sealing performance and can also
be installed by outdoor .
Polygon material made dome shield possesses
high light permeate rate, strong shock resistance
capability. The whole Aluminum base can stand
lasting shock and high temperature.
NIGHT VISION IR DOME CAMERA
4. Adjusting the Camera Direction
Camera body moves in three ways: pan, tilt and rotate.
Adjust the direction so that the lens is pointing at the
target.
5. Use the lever to adjust the view angle and focus.
Rotate 180°
Tilt 90°
Pan360°
6
.
T
urn the dome cover to adjust until the lens point at
the window, screw tightly and complete the installation.
Close
7. Connecting Low Voltage Power & Video Signal
The wiring harness have a BNC connector to accept
video signal ,the other connectors to accept the low
voltage power. For mounting directly to a wall or ceiling,
run power and video lines to the target location.
VIDEO
12VDC
NIGHT VISION IR DOME CAMERA
4
2. Safety Precautions
The installation should be made by qualified service
personnel or system installers and should confirm
to all local codes.
1.Power supply
(1) use with a 12VDC regulated power supply
(2) To prevent fire or electrical shock, UL listed class
2 wiring should be used for the 12VDC input terminal.
(3) Be used to connect each lead to the appropriate
terminal. Wrong connection may cause malfunction
and/or damage to the video camera.
2.Operating and storage locations
(1).Do not attempt to point the camera at the sun or
other extremely bright objects that cause smear to
appear no matter the camera is power on or not.
It leads to damage of the CCD(Charge Coupled
Device).
(2).When camera is installed next to equipment,
such as wireless communication device, it emits a
strong electromagnetic field, some irregularity such
as noise on the monitor screen may happen.
(3).Be sure to use a ceiling board having enough
strength to support this camera.
(4).Assemble the camera's main parts and lens
quickly in a sanitary place.
(5).Do not pull the cable, it may cause disconnection.
(6).Do not touch the inside of camera even if
something is wrong.
(7).Before installation, make sure to disconnect the
power supply first, check the ground connection,
and then install it.
(8).Operating temperature range:-10℃~+50℃,(14°F~122°F);
Storage temperature range:-20℃~+60℃,(-4°F~140°F).
(9). Be sure to use proper screws which cameras can
be beared on the material firmly.
1
NIGHT VISION IR DOME CAMERA
7. Self-Check Points
Before Consulting After-Sales Services
CONDITIONS
CHECKING POINTS
Screen
*Make sure whether power is connected correctly.
not turned on
*Check if the cable is connected correctly.
*If dust is seen through the monitor screen after
Screen not clear
fixing lens, dissemble the lens and clear off the
View angle
or is spread
dust on the surface of CCD withblower or soft cloth.
adjustment lever
Focus
adjustment lever
8. Specifications
Model
VDC-350PIV-V
Image Sensor
1/3'' SUPER HAD II CCD
Signal System
PAL
Effective Pixels
752(H)x582(V)
540TV Lines(Color), 600TV Lines(B/W )
Resolution
Minimum Illumination
0.1Lux/F1.2(IR LED OFF), 0Lux (IR LED On)
Shutter Speed
1/50-1/100,000SEC
S/N Ratio
More Than 50dB
Automatic
White Balance
AGC/BLC
Automatic
0.45
Gamma Correc tion
Sync Model
INT
Varifocal lens, f=4-9mm
Lens
IR LED
Wave Length 850nm, x 21pcs IR LED
10~15m
IR Beam Distanc e
NIGHT VISION IR DOME CAMERA
5
3. Handling of the Unit
(1) Never attempt to disassemble or modify the camera.
(2) If an abnormality should occur, immediately turn off
the power and consult your dealer.
4. Parts Description
Dome cover (transparent)
Camera body
IR-LED
Front View
5. Cover Removal and Attachment
To remove the body cover and camera body,
disassemble it with the L WRENCH provided in your
ACCESSORY set. (Rotating clockwise will close it
and rotating anti-clockwise will release it.)
Acecessories
1. PLASTIC
2. ASSY SCREW
TAPPING
ANCHOR
NIGHT VISION IR DOME CAMERA
2
IR LED Driv e
On: 1~3Lux; Off: 5~6Lux
Video output
1.0Vp-p, 75Omh, Sync Negative Polarity
DC12V Regulated
Power Input
Power Consumption
150mA(IR LED OFF)+150mA(IR LED ON)
-10℃ ～ +50℃, RH90% MAX (non-c ondensing)
Operating Temperature
Body
Aluminum
1000g
Weight
All data and specifications subject to change
without notice.
9. Type Number Overview
Model(12VDC)
VDC-350PIV-V
VDC-350NIV-V
Signal system PAL
NTSC
IR NIGHT VISION DOME CAMERA
768(H)x494(V)
10. Dimension Outline
1/60-1/100,000SEC
146mm
6
NIGHT VISION IR DOME CAMERA
Mounting Holes
Wire hole
Body cover
Camera base
BOTTOM View
3. L WRENCH
3
VDC-350NIV-V
NTSC
6
7
Advertisement
