Table of Contents
Advertisement
Quick Links
MODEL NO=
113,201170
Serial
Number ...................................
Model and serial
number
may be found
on the back
of the cabinet,
You should
record both
model and serial number
in a safe place for
future use,,
CAUTmON:
Read
GENERAL
and
ADDITIONAL
SAFETY
iNSTRUCTIONS
carefully
Sold by SEARS,
Part No. 61445
ROEBUCK
300 AMP
HiGH
FREQUENC
Y
ARC STABILIZER
A TTA CHMENT
® assembly
® operating
® repair parts
AND
CO., Chicago,
IL. 60684
U.S.A.
Printed in USA
Advertisement
Table of Contents
Related Manuals for Craftsman 113.201170
Summary of Contents for Craftsman 113.201170
- Page 1 MODEL NO= 113,201170 Serial Number ........Model and serial number may be found on the back of the cabinet, You should record both model and serial number in a safe place for future use,, 300 AMP HiGH FREQUENC CAUTmON: ARC STABILIZER A TTA CHMENT Read GENERAL...
- Page 2 SAFETY iNSTRUCTiONS TO OPERATOR FOR ALL ARC WELDING OPERATIONS power supply and obtain help frorn a qualified Protect yourself and others Failure to follow these electrician instructions may result in serious personal injury FUMES GASES BE DANGEROUS drop or insert objects through YOUR...
-
Page 3: Arc Stabilizer Attachment Is Connected
Vent hollow castings containers before 2 Inspect "ON-OFF" switch tever for cracks heating, cutting, or welding, They may explode broken parts from expansion trapped boiling 3.. inspect electrode holder jaw insulators liquids. cracks or broken parts d When not welding, place the electrode holder... -
Page 4: Table Of Contents
ARC STABILIZER if the Craftsman Arc Stabilizer fails to perform properly, due to a defect in material or workmanship, within one year from the date of purchase, Sears will repair it free of charge. This warranty applies only while this product is in use in the United States°... -
Page 5: Arc Stabilizer
aNSTALLATJON installations using a High Frequency Arc Stabilizer Arc (GTAW) process and AC welding current can Attachment will produce some radio frequency cause welder overheating. Install High Frequency radiation and will impose some high vottages on the Arc Stabilizers only with welders recommended welder, The following installation instructions... -
Page 6: Work Cable Assembly
WORK CABLE {SUPPLIED WITH ARC STABILIZER) Install the work clamp previously removed from your welder work cable on the new work cable supplied with your Stabilizer according instructions provided with your welder or work clamp The work cable supplied has terminals bolted connections on both end&... -
Page 7: Connections
ARC WELDER H_GH FREQUENCY DO NOT REVERSE ARC STABiLiZER THESE CONNECTIONS 'TOGTAWTORO._'\ JACK JACK GROUND CABLE CONNECTION WORK CABLE 2 FEET LONG ELECTRODE ELECTRODE CABLE CABLE WORK CABLE DETAIL WORK CABL_ CONNECTION CONNECTIONS TO AN AC WELDER OR AC/DC WELDER CONNECTIONS TO A DC OR AC/DC WELDER... - Page 8 POWER SUPPLY The conduit enclosing the Arc Stabilizer power Connect the Arc Stabilizer toa 115volt, 60hz, singte supply conductors must extend to the receptacle phase, 15 or' 20 ampere grounding receptacle.. into which the High Frequency Arc Stabilizer wiring must comply with the National Electric Code plugged,.
-
Page 9: Owners Manual
CERTIFICATION FCC Regulations interpret radio frequency radiation measurements High Frequency Stabilized Welding installations are required to meet radio frequency The FCC requires that the signed certificate radiation limits given Federal placed in a location where is conveniently Communications Commission (FCC) Rules and available inspection... -
Page 10: Maintenance
MAINTENANCE Cables, Plugs, and Electrode Holder or GTAW Torch The high frequency voltage generated by a High Frequency Stabilizer tends to arc through cracks, holes,and damp or weakened insulation in welding cables, jacks, plugs, electrode holders or GTAW torches. This can increase the risk of shock from the up to 80 volts AC or 100 volts DC welding voltage. - Page 11 Cleaning the Metal Before welding begun, it is important that Cleaning may be accomplished with liquid cleaners surfaces to be welded are clean Oil, grease, paint, and vapor, or mechanical methods, Liquid cleaners, rust, dirt or other contaminants should be removed such as naphtha, mineral spirits, alcohol, acetone, in order...
- Page 12 STAINLESS STEEL AC-HF DC-SP TUNGSTEN WELDING WELDING SHIELDING FILLER ME3`AL TYPE OF ELECTRODE CURRENT CURRENT GAS-ARGON THICKNESS WELD JOINT DIAMETER (AMPS) (AMPS) CU, FT,/HR. DIAMETER 3/64 (_046-) Square Groove t/16" (.052") 65-100 50-80 1/16 '_ (.062"') 3/64" (,046) Fillet 1/16" (.062") 65-100 50-80 1/16"...
-
Page 13: (Stick Welding)
5, To startthe actualweldingprocess,movethe torchin smallcirclesabove theworkuntilapool of moltenmetalis obtained.If no filler metalis required, t he weldis madebygraduallymoving (1) DEVELOP THE PUDDLE _=__ the torch along parts to be weldedto melt adjoiningedges progressively.Oscillationof DIRECTION _"""-_ {2) MOVE TORCH the torch is not required., OF WELD /WORK PIECE... - Page 14 Connect Arc Stabilizer and welder to the performance with AC connected to different same phase of the power system. welder, phases of a three phase system.. PARTS LIST FOR CRAFTSMAN 300 AMP HIGH FREQUENCY ARC STABILIZER ATTACHMENT MODEL 113,201170 Part...
- Page 15 PARTS LIST FOR CRAFTSMAN 300 AMP HIGH FREQUENCY ARC STABILIZER ATTACHMENT MODEL 113.201170 !118...
-
Page 16: Repair Parts
300 AMP HiGH FREQUENCY ARC STABHLIZER ATTACHMENT SERVICE Now that you have purchased your High Frequency Stabilizer Attachment, should a need ever exist for repair parts or services, simply contact any Sears Service Center most Sears, Roebuck stores, Be sure provide atl pertinent factswhen...