NEC 4650NX - SuperScript Color Laser Printer Quick Start

NEC0
UNPACKING THE PRINTER
1.
Open the top of the packing box.
R emove the Accessory kit and the
Starter kit.
IMPORTANT! Pick the location for your
printer carefully. Make sure it has good
ventilation and that the surface is level. For
more information see Chapter 2 of the
SuperScript 4650 Series User's Guide.
VERIFYING THE BOX CONTENTS

4650 Series Printer

Starter Kit
Includes a standard 250-sheet
Paper Tray 1 and a power cord.
•
NEC Paper Sample Pack
•
Software Envelope
•
SuperScript 4650 Series CD
•
SuperScript 4650 Series User's Guide
•
SuperScript Color Laser Network
Guide (4650N or 4650NX only)
ADDING THE PAPER TRAY 2 UNIT (4650NX ONLY)
1. R emove the Paper Tray 2 Unit from its
packaging.
NOTE: Paper Tray 2
will increase the
printer's height by
4 inches.
6.
F acing the back of
the printer, locate
the Connector
Cable at the rear of
the Paper Tray 2
Unit. Make sure
the cable is
extending past the
INSTALLING THE BELT CARTRIDGE
1. Open the F ront Cover using the 2. Open the Top Cover by sliding
Front Cover Release Latch. the Top Cover Release Button
forward.
INSTALLING THE FUSER OIL BOTTLE & CLEANING ROLLER
1. 2.
P ush the Fuser Roller Release Mak e sure the Lock Tabs are in
Tabs backward and pull out the the open position.
orange Tension Release Pins.
WARNING!
result if fuser oil accidently spills inside the
printer.
INSTALLING THE TONER MODULES
1. The color labels inside the front of the
printer indicate where to place each of
the color Toner Modules.
LOADING LETTER PAPER
1.
Remove Paper Tray 1.
PRINTING A STARTUP PAGE
1.
Connect the Power
Cord to the back of
the printer.
2.
T urn the large plastic box screws at the bottom of the
box to the left (A) and pull out to remove (B).
Using your thumb and finger , remove the plastic
screw sleeves from the box (C).
A B C
Accessory Kit
Belt Cartridge
Fuser Oil Bottle
2.
L ocate the packet of brackets and thumb
screws and set aside. Extend the
Connector Cable away from the unit.
Connector Cable
Screw Hole
7. R emove the Cable
Connector Doors from
both the printer and the
Paper Tray 2 Unit. Set the
doors aside.
3. Flip up the Belt Car tridge
Locking Levers inside the top of
the printer.
3.
R emove the Fuser Oil Bottle
from its plastic bag and set into
place with the shunt valve down
and the labeled side facing the
front.
Damage to internal parts may
Keep printer level at all times.
2. Begin with the Cyan Toner Module.
R emove from its plastic bag and rock
gently three or four times.
R emove the tape from the Module.
R emove (but
save) the packing
face plate.
2.
Squeeze on both sides of the length tab
and slide it into place. The outside of the
tab should match letter size (LTR) marked
on the inside of the tray.
2.
Turn on the Power button located on the
lower left front corner of the printer.
4 6 5 0
3.
Lif t off the outer box. Open the
plastic bag that contains the
printer and slide it down. Do not
attempt to lift the printer by its
plastic bag!
1 Black Toner Module
1 Cyan Toner Module
1 Magenta Toner Module
1 Yellow Toner Module
Fuser Cleaning Roller
Fuser Oil Syringe (save for future use)
3. S et the Paper Tray 2 Unit next to the
printer. Carefully align the Paper Tray 2
Unit to the printer.
K eeping the printer
level, have two
people lift the printer
up and onto the
Paper Tray 2 Unit.
8. Plug the P aper Tray 2 unit
Connector Cable into the
printer socket.
4. R emove the Tension Release
Pins and the black protective
sheet from the Belt Cartridge.
Be careful not to scratch the
shiny green surface.
4.
R emove the Fuser Cleaning
Roller from its plastic bag. Place
in printer top with the exposed
part of the roller facing the
front.
3. Hold the module level and slide into
place along the racks in the printer.
3.
Squeeze the left side guide and
slide it to match your paper's
width. The inside of the tab
should match the desired size
on the tray.
3.
Indicator lights cycle
and messages
appear on the
Operator Panel.
Power Warning Online
Menu OnLine
Data OHT Label
Feed Item Media
Previous Next Select
4 6 5 0 N
Q U I C K S TA R T
4.
With one per son on each side of the printer, grasp the
printer at the hand grips where they are exposed by
notches in the foam padding. Place on a sturdy level
desk or table.
Paper Tray 2 Unit
(Additional 250-sheet paper tray
included only with the 4650NX)
4. L ocate the metal tab with screw hole on
each side of the Paper Tray 2 Unit.
Take a metal bracket
from the packet and
hold it at a slight
angle away from
you. Slide the bracket
up into the hole
beneath the printer.
9.
S witch the two Cable
Connector Doors. Place
the small door on the
printer and the large
door on the Paper Tray 2
Unit.
5. Slide the Belt Car tridge into the
guides.
Do not force it!
The flat side
of the Belt
Cartridge
faces front.
5.
T urn the Lock Tabs to the locked
position.
4. Repeat steps 2 and 3 for the remaining
Toner Modules.
4.
Fill the paper tray.
Do not overfill paper tray!
NOTE: Load and print only regular paper
(16 to 24 lb.) until you read Chapter 2 of
your User's Guide. Other media must be
selected on the Operator Panel.
4.
A Startup Page
prints and READY
GENERAL INFO
appears on the Printer Name: SuperScript 4650N
Software Version: 0.04
Build Time: 936928632
PostScript Version: 3010.108
PrintAgent Version: 1.008
Disk Resource Version: 0.0.4N
Operator Panel.
STORAGE
RAM Installed: 128 Megabytes
Disk Size: 1964.03 Megabytes
Disk Free: 1667.97 Megabytes
JOB OPTIONS
Number of Copies: 1
Print PS Errors: Enabled
Wait Timeout: 240 seconds
Job Timeout: Never
ENGINE INFO
Default Resolution: 600.0 X 600.0 DPI
Edge Smoothing: Disabled
Jam Recovery: Enabled
Tray 1: Letter
Tray 2: Legal
Pages Printed: 2182
PARALLEL PORT
Status: Enabled
Bi-di: Enabled
Personality: AutoSelect
NETWORK PORT
Status: Enabled
Personality: AutoSelect
Web Address: http://131.241.45.88
For sales information, call (800) NEC-INFO or visit our website at http://www.nectech.com. For supplies, call (800) 632-2326
and may be registered in certain jurisdictions. All other trademarks and registered trademarks are the property of their respective owners. ©1999 NEC Technologies, Inc. All rights reserved. NEC and the NEC logo are registered trademarks and SuperScript is a trademark of NEC Corporation. Adobe, PostScript and the PostScript logo are trademarks of Adobe Systems Incorporated or its subsidiaries
4 6 5 0 N X
The printer and packaging
weighs approximately 100
lbs. To set up the printer and
move it requires two adults.
Not included ...
To connect your printer, you need to
provide the proper parallel and/or
network cable.
IEEE 1284
Bidirectional Parallel Cable
Category 5 Twisted Pair Cable
with RJ-45 Connectors for
10/100Base-T Ethernet
5. Carefully align the hole in eac h metal
bracket with the corresponding screw
hole on the Paper
Tray 2 Unit. Insert
and tighten the
thumb screws.
10.
Snap on the
left and right
Paper Tray 2
Unit covers.
6.
Flip down the Belt Car tridge
Locking Levers.
6.
Close the Top
Cover of the
printer.
5. Close the Front Cover.
IMPORTANT! If you need to move the printer once the
accessories are installed, please see Appendix D of the
SuperScript 4650 Series User's Guide, "Moving Your
Printer. "
Instructions Continued
On Reverse Side