Cisco III - Supervisor Engine III Message Manual page 63

Chapter 2 Messages and Recovery Procedures
Error Message %C7600_SIP200_SPITX-3-DESCR_ERR_SPA2: SPAstatus=[hex],
syndrome=[hex], RdRspOvf=[int], RdRspTo=[int], OvfVal=[int], OvfCh=[int],
OvfDescHi=[hex], OvfDescLo=[hex], DisChk=[int], SeqErrVal=[int], SeqErrCh=[int]
Explanation
while processing a TX descriptor. This condition could cause packets to drop.
Recommended Action
Toolkit at
assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create
representative and provide the representative with the output of the show tech-support command
for the line card and the show platform hardware spi4 spa-id efc channel [channel-id] command
for the SPA.
Error Message %C7600_SIP200_SPITX-3-DESCR_ERR_SPA3: SPAstatus=[hex],
syndrome=[hex], RdRspOvf=[int], RdRspTo=[int], OvfVal=[int], OvfCh=[int],
OvfDescHi=[hex], OvfDescLo=[hex], DisChk=[int], SeqErrVal=[int], SeqErrCh=[int]
Explanation
while processing a TX descriptor. This condition could cause packets to drop.
Recommended Action
Toolkit at
assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create
representative and provide the representative with the output of the show tech-support command
for the line card and the show platform hardware spi4 spa-id efc channel [channel-id] command
for the SPA.
Error Message %C7600_SIP200_SPITX-3-DMA_SQERR: Syndrome=[hex], SPA=[int], Ch=[int],
RdSz=[int], RdOff=[int][chars]
Explanation
DMA operation. This condition could cause packets to drop.
Recommended Action
Toolkit at
assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create
representative and provide the representative with the output of the show tech-support command
for the line card and the show platform hardware spi4 spa-id efc channel [channel-id] command
for the SPA.
Error Message %C7600_SIP200_SPITX-3-EFC_ERR_SPA0: SPAstatus=[hex][chars]
Explanation
extended flow control bus interface. This condition could cause packets to drop.
Recommended Action
Toolkit at
assistance, open a case with the Technical Assistance Center via the Internet
OL-11469-02
The egress SPI4.2 device on the line card detected a sequence or FIFO overflow error
If this problem recurs, search for resolved software issues using the Bug
http://tools.cisco.com/Support/BugToolKit/
The egress SPI4.2 device on the line card detected a sequence or FIFO overflow error
If this problem recurs, search for resolved software issues using the Bug
http://tools.cisco.com/Support/BugToolKit/
The egress SPI4.2 device on the line card detected a sequence error while processing a
If this problem recurs, search for resolved software issues using the Bug
http://tools.cisco.com/Support/BugToolKit/
The egress data path device on the line card detected an error condition with the
If this problem recurs, search for resolved software issues using the Bug
http://tools.cisco.com/Support/BugToolKit/
Catalyst Supervisor Engine 32 PISA Cisco IOS System Message Guide, Release 12.2ZY
C7600_SIP200_SPITX Messages
under Product cat6000. If you still require
or contact your Cisco technical support
under Product cat6000. If you still require
or contact your Cisco technical support
under Product cat6000. If you still require
or contact your Cisco technical support
under Product cat6000. If you still require
2-33