Table of Contents
Advertisement
Quick Links
939AGP-EC/939AGP-G-EC
USER'S MANUAL
M/B For Socket 939 AMD Athlon64
Processor
NO. G03939AGPECR110
Rev:1.0
Release date: April 2005
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
Advertisement
Table of Contents
Related Manuals for JETWAY 939AGPECR110
Summary of Contents for JETWAY 939AGPECR110
- Page 1 939AGP-EC/939AGP-G-EC USER'S MANUAL M/B For Socket 939 AMD Athlon64 Processor NO. G03939AGPECR110 Rev:1.0 Release date: April 2005 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
-
Page 2: Table Of Contents
TABLE OF CONTENT USER’S NOTICE........................ii MANUAL REVISION INFORMATION ................ii COOLING SOLUTIONS ......................ii CHAPTER 1 INTRODUCTION OF 939AGP-EC/939AGP-G-EC MOTHERBOARD FEATURE OF MOTHERBOARD ..................1 1-1.1 SPECIAL FEATURES OF MOTHERBOARD............2 SPECIFICATION........................3 PERFORMANCE LIST ......................4 LAYOUT DIAGRAM & JUMPER SETTING ..............5 CHAPTER 2 HARDWARE INSTALLATION HARDWARE INSTALLATION STEPS ................ -
Page 3: User's Notice
USER’S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER. THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE 939AGP-EC/939AGP-G-EC MOTHER-BOARD AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE. -
Page 4: Chapter 1 Introduction Of 939Agp-Ec/939Agp-G-Ec Motherboard
Chapter 1 Introduction of 939AGP-EC/939AGP-G-EC Motherboard 1-1 Feature of motherboard The 939AGP-EC/939AGP-G-EC motherboard is design for use 64bit AMD Athlon64 (K8) Processor in 939 Pin HyperTrnsport Processor with the VIA K8T800 Pro Chipset delivers a high performance and professional desktop platform solution. Which utilize the Socket 939 design and the memory size expandable to 4.0GB. -
Page 5: 1-1.1 Special Features Of Motherboard
1-1.1 Special Features of motherboard CPU Thermal Throttling Technology ---( The CPU Overheat Protection Technology) To prevent the increasing heat from damage of CPU or accidental shutdown while at high workload, the CPU Thermal Throttling Technology will force CPU to enter idle mode from 87.5% to 12.5% according to preset CPU operating temperature in BIOS (from 20℃... -
Page 6: Specification
1-2 Specification Spec Description Design ATX form factor 4 layers PCB size: 30.4x24.3cm Chipset VIA K8T800 Pro North Bridge Chipset VIA VT8237 South Bridge Chipset Support 64bit AMD Athlon64 939-Pin package utilizes Flip- CPU Socket 939 Chip Pin Grid Array package processor Support CPU Frequency 1GHz Support up to 3800+ processor Reserves support for future AMD Athlon64 939-pin processors... -
Page 7: Performance List
1-3 Performance List The following performance data list is the testing result of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users (the different Hardware & Software configuration will result in different benchmark testing results.) Performance Test Report AMD K8 ATHLON 64 3400+ Support... -
Page 8: Layout Diagram & Jumper Setting
1-4 Layout Diagram & Jumper Setting 10/100M Giga LAN Surrback PRINT Line-IN CEN/LFE PS/2 Mouse Line-OUT MIC-IN PS/2 Keyboard Surround COM2 COM1 USB1 ATX 12V Power Connector PS2 KB/Mouse Port DDR Socket X4 PC99 Back Panel ATX Power Connector CPU FAN CPU Socket USB Port/ 10/100M LAN Connector USB Port/ Giga LAN Connector... - Page 9 Jumpers Jumper Name Description Page CMOS RAM Clear JBAT 3-pin Block Keyboard/USB0,1 Power On 3-pin Block Enabled/Disabled On board RealTek LAN Enabled/Disabled 3-pin Block USB Power On Enabled/Disabled 3-pin Block Connectors Connector Name Description Page ATXPWR ATX Power Connector 24-pin Block P.13 ATX12V ATX 12V Power Connector...
-
Page 10: Chapter 2 Hardware Installation
Chapter 2 Hardware installation 2-1 Hardware installation Steps Before using your computer, you had better complete the following steps: 1. Check motherboard jumper setting 2. Install CPU and Fan 3. Install System Memory (DIMM) 4. Install Expansion cards 5. Connect IDE and Floppy cables, Front Panel /Back Panel cable 6. -
Page 11: Install Cpu
(2) On Board RealTek LAN function Enabled/Disabled: JP2 (for 939AGP-G-EC only) 1-2 closed On Board LAN Enabled 2-3 closed On Board LAN Disabled (Default) On Board RealTek LAN Setting (3) Keyboard/USB Power On function Enabled/Disabled: JP1, JP3 1-2 closed KB/USB Power ON Disable 2-3 closed KB/USB Power ON Enabled (Default) Keyboard/USB Power On Setting... -
Page 12: About Intel Amd K8 939-Pin Cpu
Sound (interface) - the interface between the sound card or integrated sound connectors and speakers, MIC, game controllers, and MIDI sound devices. LAN (interface) - Local Area Network - the interface to your local area network. BIOS (Basic Input/Output System) - the program logic used to boot up a computer and establish the relationship between the various components. -
Page 13: Install Memory
2-4 Install Memory This motherboard provides four 184-pin DDR DUAL INLINE MEMORY MODULES (DIMM) sites for DDR memory expansion available from minimum memory size of 128MB to maximum memory size of 4.0GB DDR SDRAM. Valid Memory Configurations Bank 184-Pin DIMM Total Memory Bank 0, 1 (DIMM1) DDRDDR266/DDR333/DDR400... -
Page 14: Expansion Card
2-5 Expansion Cards WARNING! Turn off your power when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. 2-5-1 Procedure For Expansion Card Installation 1. Read the documentation for your expansion card and make any necessary hardware or software setting for your expansion card such as jumpers. -
Page 15: Interrupt Request Table For This Motherboard
2-5-3 Interrupt Request Table For This Motherboard Interrupt request are shared as shown the table below: INT A INT B INT C INT D INT E INT F INT G INT H Slot 1 Slot 2 Slot 3 Slot 4 Slot 5 Onboard USB 1 Onboard USB 2... -
Page 16: Connectors, Headers
2-6 Connectors, Headers 2-6-1 Connectors (1) Power Connector (24-pin block) : ATXPWR ATX Power Supply connector. This is a new defined 24-pins connector that usually comes with ATX case. The ATX Power Supply allows to use soft power on momentary switch that connect from the front panel switch to 2-pins Power On jumper pole on the motherboard. - Page 17 PS/2 Mouse & PS/2 Keyboard Connector: PS2KBMS The connectors for PS/2 keyboard and PS/2 Mouse. USB Port connector: USB0/USB1 The connectors are 4-pin connector that connect USB devices to the system board. LAN Port connector: UL1/USBLAN This connector is standard RJ45 connector for Network The UL1 support 10M/100Mb/s data transfer rate (for 939AGP-EC only) The USBLAN support 10M/100M/1G b/s data transfer rate ( for 939AGP-G-EC only) Parallel Port Connector (25-pin female): PARALLEL...
- Page 18 Floppy drive Connector (34-pin block): FDD This connector supports the provided floppy drive ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to the floppy drives. Pin 1 Floppy Drive Connector (10) Primary IDE Connector (40-pin block): IDE1 This connector supports the provided IDE hard disk ribbon cable.
-
Page 19: Headers
Two hard disks can be connected to each connector. The first HDD is referred to as the “Master” and the second HDD is referred to as the “Slave”. For performance issues, we strongly suggest you don’t install a CD-ROM or DVD-ROM drive on the same IDE channel as a hard disk. - Page 20 USB Port Headers (9-pin) : USB2/USB3 These headers are used for connecting the additional USB port plug. By attaching an option USB cable, your can be provided with two additional USB plugs affixed to the back panel. USB2 USB3 Pin 1 P in 1 USB Port Headers Speaker connector: SPEAK...
- Page 21 FAN Headers (3-pin) : SFAN1, SFAN2, CPUFAN These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different. The red wire should be positive, while the black should be ground. Connect the fan’s plug to the board taking into consideration the polarity of connector.
-
Page 22: Starting Up Your Computer
2-7 Starting Up Your Computer 1. After all connection are made, close your computer case cover. 2. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V 240V or 110V 120V depending on your country’s voltage used. -
Page 23: Chapter 3 Introducing Bios
Chapter 3 Introducing BIOS The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization. -
Page 24: The Main Menu
3-3 The Main Menu Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen. The Main Menu allows you to select from fourteen setup functions and two exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu. -
Page 25: Standard Cmos Features
Load Optimized Defaults Use this menu to load the BIOS default values these are setting for optimal performances system operations for performance use. Load Standard Defaults Use this menu to load the BIOS default values for the stable performance system operation that are factory settings for normal use. -
Page 26: Advanced Bios Features
Time The time format is <hour><minute><second>. Primary Master/Primary Slave Secondary Master/Secondary Slave Press PgUp/<+> or PgDn/<–> to select Manual, None, Auto type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. - Page 27 Anti-Virus Protection Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep. Disabled (default) No warning message to appear when anything attempts to access the boot sector or hard disk partition table.
-
Page 28: Advanced Chipset Features
Security Option This category allows you to limit access to the system and Setup, or just to Setup. The system will not boot and access to Setup will be denied if the System correct password is not entered at the prompt. Setup (default) The system will boot, but access to Setup will be denied if the correct password is not entered prompt. -
Page 29: Dram Timing Settings
3-6-1 DRAM Timing Settings Phoenix – AwardBIOS CMOS Setup Utility DRAM Timing Settings Auto Configuration Auto Item Help x DRAM CAS Latency CL=2.5 x RAS Active Time x RAS to CAS Delay Menu Level >> x RAS Precharge Time x DRAM Bank Interleaving Enabled Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help... -
Page 30: Pci Timing Settings
3-6-3 PCI Timing Settings Phoenix – AwardBIOS CMOS Setup Utility PCI Timing Settings Item Help PCI Master 1 WS Write Disabled PCI Master 1 WS Read Disabled CPU to PCI Post Write Enabled Menu Level >> PCI Delay Transaction Disabled VLink Data Rate Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help... -
Page 31: Integrated Peripherals
3-7 Integrated Peripherals Phoenix – AwardBIOS CMOS Setup Utility Integrated Peripherals > OnChip IDE Function Press Enter Item Help > OnChip Device Function Press Enter > OnChip SuperIO Function Press Enter Init Display First PCI Slot Menu Level > Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults... -
Page 32: Onchip Device Function
OnChip IDE Channal0/Channel1 The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Enabled to activate each channel separately. The settings are: Enabled and Disabled. Primary/Secondary Master/Slave PIO The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports. -
Page 33: Onchip Super Io Function
Onboard AC97 Audio Device This item allows you to decide to enable/disable the chipset family to support AC97 Audio. The settings are: Enabled, Disabled. USB 2.0 Support Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB peripherals. -
Page 34: Power Management Setup
SPP/EPP/ECP/ECP+EPP To operate the onboard parallel port as Standard Parallel Port only, choose “SPP.” To operate the onboard parallel port in the EPP modes simultaneously, choose “EPP.” By choosing “ECP”, the onboard parallel port will operate in ECP mode only. Choosing “ECP+EPP”... -
Page 35: Pm Wake Up Events
3-8-1 Wake up Events Phoenix – AwardBIOS CMOS Setup Utility Wake Up Events Item Help LPT & COM LPT/COM HDD & FDD PCI Master Menu Level >> Wake-Up on Ring Disabled Wake-Up on PCI PME Disabled PS2 KB Wake up Selection Hot Key Wake-Up on Hot Key (PS2 KB) Disabled... -
Page 36: Irq Resources
IRQ Resources When resources are controlled manually, assign each system interrupt a type, depending on the type of device using the interrupt. Please refer to section 3-9-1 PCI/VGA Palette Snoop Leave this field at Disabled. The settings are Enabled, Disabled. 3-9-1 IRQ Resources Phoenix –... -
Page 37: Smart Fan Configurations
Shutdown Temperature This item can let users setting the Shutdown temperature, when CPU temperature over this setting the system will auto shutdown to protect CPU. Show PC Health in Post During Enabled, it displays information list below. The choice is either Enabled or Disabled CPU Thermal Throttling Temp This item allows you to activate the CPU Thermal Throttling function when the CPU temperature is over the value which you set to low down the CPU temperature when at high... -
Page 38: Miscellaneous Control
3-11 Miscellaneous Control This section is for setting CPU Frequency/Voltage Control. Phoenix – AwardBIOS CMOS Setup Utility Miscellaneous Control Auto Detect PCI Clock Enabled Item Help Spread Spectrum Disabled Linear PCIExpress Clock ** Current CPU Clock 200Mhz ** Menu Level > CPU Clock at Next Boot ** Current DRAM Clock 200MHZ **... -
Page 39: Load Standard/Optimized Defaults
3-12 Load Standard/Optimized Defaults Load Standard Defaults When you press <Enter> on this item, you get confirmation dialog box with a message similar Load Standard Defaults (Y/N)? N Pressing <Y> loads the BIOS default values for the most stable, minimal-performance system operations. -
Page 40: Chapter 4 Driver & Free Program Installation
Chapter 4 DRIVER & FREE PROGRAM INSTALLATION Check your package and there is A MAGIC INSTALL CD included. This CD consists of all DRIVERS you need and some free application programs and utility programs. In addition, this CD also include an auto detect software which can tell you which hardware is installed, and which DRIVERS needed so that your system can function properly. -
Page 41: Via 4In1 Install Via Service Pack 4 In 1 Driver
4-1 VIA 4IN1 Install VIA Service Pack 4 IN 1 Driver * The path of the file is X:\VIA\DRIVER\SETUP.EXE IDE : VIA ATAPI VENDOR SUPPORT DRIVER IS USED TO FIXED COMPATIBILITY ISSUE FOR IDE DEVICES AGPVXD : VIA AGPVXD DRIVER IS TO BE INSTALLED, IF YOU ARE USING AN AGP VGA CARD, VIAGART.VXD WILL PROVIDE SERVICE ROUTINES TO YOUR VGA DRIVER AND INTERFACE DIRECTLY TO HARDWARE, PROVIDING FAST GRAPHIC ACCESS... -
Page 42: Sound Install Alc Audio Codec Driver
7. Click NEXT to Install VIA AGP VXD Driver 8. Click NEXT to Install VIA IRQ Routing Mini port Driver 9. Click Finish to restart computer 4-2 SOUND install ALC Audio Codec Driver 1. Click SOUND when MAGIC INSTALL 2. Click NEXT When Realtek High Definition MENU appears Audio driver windows appear... -
Page 43: Lan Install Realtek 8110S Giga Ethernet Driver
3. Click FINISH and restart your computer 4. Manual Sound Effect Setting 5. Speaker configuration setting 6. SPDIF out setting 4-3 LAN install Realtek RTL8110S Gigabit Ethernet NIC Driver (for 939AGP-G-EC) 10. Click LAN when Magic Install Menu appear 11. Click finish, and select restart computer... -
Page 44: Lan2 Install Via 10/100Mb Lan Controller Driver
4-4 LAN2 Install VIA 10/100MB LAN Controller Driver (for 939AGP-EC) The VIA 10/100Mb PCI Ethernet Adapter Driver path is X:\VIA\LANDRV Click LAN when Magic Install Menu appear 2. Setup VIA 10/100Mb PCI Ethernet Driver Driver install Finish, Click Yes and Restart When windows ask VIA 10/100Mb PCI Computer Ethernet Adapter driver path, Change... -
Page 45: Sata Install Via Serial Ata Driver
3. Select Install USB Driver and Click NEXT Select FINISH and Restart your Computer 5. Check device working properly in Device Manager The Path of the file is X:\VIA\VIAUSB20\SETUP.EXE 4-6 SATA Install VIA Serial ATA 1. Click SATA when MAGIC INSTALL 2. - Page 46 3. When license agreement appear, choose I 4. Select you want to install driver agree and click NEXT 5. Review install driver and utility component, 6. Click FINISH and restart your computer then click NEXT Making SATA HDD driver diskette before Install WindowsXP/2000 If you only have Serial ATA HDDs on your system, before you install the Windows XP or Windows 2000, you will need to make a SATA HDD driver diskette before you start to install the Operating System.
-
Page 47: Pc-Cillin Install Pc-Cillin2004 Anti-Virus Program
4-7 PC-CILLIN Install PC-CILLIN 2004 Anti-virus program 1. Click PC-CILLIN when MAGIC INSTALL 2. Click NEXT when the "Trend Micro internet MENU appear security" installshield wizard windows appear 3. This is license agreement, select "I Accept 4. Click NEXT and Enter your Customer the terms"... -
Page 48: How To Disable On-Board Sound
7. After PC-CILLIN 2004 complete, Please register your information and we recommend select update item to download newest engine code and virus code Note : Please install ACROBAT READER, Before you read PC-CILLIN 2004 User Manual, the path at X:\acrobat\adberdr6_enu_full.exe 4-8 HOW TO DISABLE ON-BOARD SOUND Enter BIOS SETUP choose INTEGRATE PERIPHERALS choose ON-CHIP DEVICE FUNCTION choose AC97 SOUND DEVICE... -
Page 49: Pro Magic Plus Function Introduction
Pro Magic Plus- an instant system recovery software tailored to solve these problems for you. It combines various application tools (e.g. anti-virus, backup software, uninstall software, multi-boot software) to satisfy your needs of all sorts of system protections. What functions does Pro Magic Plus have? Instant System Restoration –... -
Page 50: System Requirements
NOTE: Functions of each version will differ from each other, and will be based on the function descriptions of each version. System Requirements ◇ First OS must be Windows 98 SE/ME/2000/XP ◇ Support Only Windows OS (No Linux) ◇ Windows server OS and Windows NT not supported ◇...