Page 1
FIXED IR DOME CAMERA TK-T2101RU FIXED IR DOME CAMERA TK-T2101RE Instructions...
Page 3
Important Safety Information Warning and Operating Notes Installation and serving the camera should be performed only by qualified and experienced technicians to conform to all local codes and to maintain your warranty. WARNING! The use of CSA certified/ UL Listed Class 2 power adapters are required to ensure compliance. Note: This product is intended to be supplied by a Listed Direct Plug-In Power Unit marked “Class 2”...
TABLE OF CONTENTS 1. Introduction .................. 3 1.1 Before You Begin ----------------------------------------------------------------- 3 1.2 Dimensions ----------------------------------------------------------------------- 3 1.3 Names of Camera Parts --------------------------------------------------------- 4 1.4 Routine Maintenance ------------------------------------------------------------ 4 2. Installation ................... 5 2.1 Disassembling the Camera ------------------------------------------------------ 5 2.2 Connecting the wiring ----------------------------------------------------------- 6 2.3 Mounting the Camera ------------------------------------------------------------ 6 2.4 Optional Camera Settings ------------------------------------------------------- 7 2.5 Adjusting the Camera Position -------------------------------------------------- 8...
INTRODUCTION 1. Introduction The dome camera is ideal for indoor installation in commercial and residential environment. With 3-axis mount support, it provides flexible installation on a ceiling or wall even at an angle. 1.1 Before You Begin Please read this manual carefully before you install the dome camera. Keep this guide for future reference.
INTRODUCTION 1.3 Names of Camera Parts Figure 1-1 Camera parts 1. Conduit hole used for surface run power/video connector 2. Bottom case 3. Camera housing 4. Dome cover 5. IR board a. AC 24V / DC 12V power input connector (red +, black -) b.
INSTALLATION 2. Installation 2.1 Disassembling the Camera Before you mount and adjust the camera, follow these steps to disassemble the camera. 1. Insert a coin or flat tool to the side hole and twist to remove the dome cover. 2. Remove the dome cover (#2). 1.
INSTALLATION 2.2 Connecting the wiring Refer to Figure 1-1 to connect the video connect output connector (#b) and 24 VAC/12 VDC power connector (#a). Caution: For DC power supply use, make sure the polarity is correct to avoid malfunction and / or camera damage. 2.3 Mounting the Camera 1.
INSTALLATION 2.4 Optional Camera Settings Refer to Figure 2-3 to locate the OSD joystick control on the camera board. Use the joystick to access the OSD menu and configure the camera settings as required. To use the OSD joystick control: •...
INSTALLATION 2.5 Adjusting the Camera Position The dome camera has three axes for positioning the camera. While monitoring the picture on the monitor, adjust the camera position as follows: Horizontal Adjustment Rotate 3D assembly in the base. Do not turn assembly more than 360°...
INSTALLATION 2.7 Completing the Installation Once all adjustments are done, attach and secure the camera housing: 1. Use a soft, lint-free cloth to wipe the dome cover clean and remove fingerprints. 2. Assemble the dome cover (#2) and the bottom case (#1). Figure 2-5 Completing the installation...
OSD SETTINGS 3. OSD Settings Use the OSD menu to set up the camera for optimum performance. LENS AUTO PRIVACY SHUTTER/AGC AUTO DAY/NIGHT AUTO WHITE BAL BACKLIGHT CAMERA ID PICT ADJUST SYNC LANGUAGE ENGLISH MOTION DET CAMERA RESET NEXT BACK EXIT SAVE ALL EXIT...
OSD SETTINGS If SHUTTER/AGC is set to MANUAL, the submenu is shown as below. The shutter speed is a variable from 1/50(1/60)sec to 1/10000sec and the AGC is selectable depending on your environment condition. MODE SHUT+AGC SHUTTER 1/50(1/60) Recommended settings according to the application: 1.
OSD SETTINGS • PUSH: When selected in the appropriate position, the whole area will perform white balance. • PUSH LOCK: When selected in the appropriate position, WHITE BALANCE will perform once. 3.4 BACKLIGHT Set Backlight compensation function. It controls the light level to overcome sever backlight conditions.
OSD SETTINGS Note: If you enable MOTION DET function, then PRIVACY function will support 4 zones only. REA SEL BOTTOM LEFT RIGHT COLOR TRANSP 0.00 MOSAIC 3.9 DAY/NIGHT The camera will automatically switch to B/W mode when the illumination is under a certain threshold.