Table of Contents
Advertisement
Destination Names" (page 422) and "Setting a Logical
V/K Pair" (page 386).
Colors of lit cross-point buttons
In a single cross-point button row, only the last pressed
button is active, and is lit amber or red.
Color of button
Button state
when lit
Amber
Low tally
Selected signal is not included in the final
output image
Red
High tally
Selected signal is included in the final
output image
Note
When second delegation mode is enabled on the AUX bus
control block, 4th row cross-point buttons are lit green in
the low tally state.
Cross-point indicators
When lit, these indicate the logical V/K pair color linked
to the video signal logical V/K pair assigned to buttons on
the 3rd row of the cross-point control block/AUX bus
control block (AUX bus operation mode).
The color of the cross-point indicators does not change
even if a 3rd row button is lit red or amber.
Cross-Point Hold
Setting cross-point hold enables you to recall an effect
timeline or snapshot while keeping the current cross-point
selection unchanged.
You can set cross-point hold for each cross-point button
row.
To set cross-point hold, press the [XPT HOLD] button,
turning it on, for the 1st row to 4th row assigned to the
cross-point pad/function button section.
In a cross-point control block on the ICP-X7000, you can
also set cross-point hold for each bus using the [XPTHLD
XXX] button (where "XXX" is the bus name) assigned to
the cross-point pad.
Note
When the switcher bank operation mode is set to multi
program 2 mode, the following cross-point hold setting
buttons function as buttons for the side (main or sub)
selected by the [MAIN] button/[SUB] button. When both
the [MAIN] button and [SUB] button are selected,
settings are applied on both main and sub.
• [XPT HOLD] button: 1st row to 4th row cross-point
hold (only when the background A bus, background B
bus, or utility 2 bus is assigned to a button row)
• [XPTHLD A] button: Cross-point hold for the
background A bus
• [XPTHLD B] button: Cross-point hold for the
background B bus
• [XPTHLD UTL2] button: Cross-point hold for the
utility 2 bus.
Key bus cross-point hold
For a key bus, the cross-point hold operation mode
specified in the Home > Setup > Switcher > Custom >
Key/Wipe menu (19103.43) is applied.
The following three operation modes can be set.
Key disable: Mode which maintains cross-point selection
state and key settings information
Key disable (including key state): Mode which maintains
cross-point selection state, key setting information,
and the key inserted/removed (on/off) state
Cross-point hold: Mode which maintains cross-point
selection state only
For details, see "Setting the Cross-Point Hold Operation
Mode" (page 400).
Bus override
This function allows you to temporarily set cross-point
hold for specific cross-point buttons only.
It is enabled for background A bus and background B bus
cross-point buttons only.
When you press and hold a cross-point button and recall
a snapshot, the cross-point selection state is maintained
for the pressed button only. The cross-point selection
state is maintained while the button is pressed, even when
executing an effect timeline.
Selecting a Key Fill Signal/Key
Source Signal
You can select a key fill signal and key source signal
using the following methods.
To select a key fill signal
• Press a cross-point button in the cross-point button row
assigned with the key bus.
• In key bus mode and free assign mode, press and hold a
key bus delegation button in the cross-point pad/
function button section and press a cross-point button in
the 1st row.
• In key/AUX bus delegation mode, press a key bus
delegation button in the 1st row and press a cross-point
button in the 2nd row.
• On the Flexi Pad control block in key operation mode,
press and hold a key delegation button in the memory
recall section and press a cross-point button in the 1st
row in the cross-point control block.
• In key bus mode and free assign mode, press and hold
the [SPLT] button in the key control block and press a
94
Advertisement
Table of Contents
