Maintenance - Makita LM001J Instruction Manual

MAINTENANCE

WARNING:
Always be sure that the lock
key and battery cartridge are removed from the
mower before storing or carrying the mower or
attempting to perform inspection or maintenance.
WARNING:
Always remove the lock key when
the mower is not in use. Store the lock key in a
safe place out of reach of children.
WARNING:
Wear gloves when performing
inspection or maintenance.
WARNING:
Always wear the safety goggles or
safety glasses with side shields when performing
inspection or maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Maintenance
1.
Remove the lock key and battery cartridge, and
then close the battery cover.
2. Put the mower on its side. Clean grass clippings
accumulated on the underside of mower deck.
3. Pour water toward the bottom of the machine to
which the blade is attached.
NOTICE:
Do not wash the machine with high
pressure water.
4. Check all nuts, bolts, screws, etc. for tightness.
5.
Inspect moving parts for damage, breakage, and wear.
Damaged or missing parts should be repaired or replaced.
6. Store the mower in a safe place out of the reach of children.
Carrying the mower
CAUTION:
Before carrying the mower, make
sure that the battery cartridge and lock key are
removed.
When carrying the mower, hold the rear grip and the
lower holding part at the front of the machine with two
people as shown in the figure.
► Fig.35: 1. Lower holding part 2. Rear grip
Storing
CAUTION:
When putting the machine in the
upright position, place the machine on a flat and
stable surface. If the machine is placed on an unsta-
ble surface, the machine may fall over and cause an
injury.
Store mower indoors in a cool, dry and locked place.
Don't store the mower and charger in locations where
the temperature may reach or exceed 40 °C.
1. Remove the battery cartridge and lock key.
2. Turn the knob 90° while pulling the knob on the
lower handle to release the locking pin. Perform the
same procedure on the other side, and then fold the
handle.
► Fig.36: 1. Knob
NOTE: Supporting the handle makes it easier to
release the locking pin when pulling the knob.
3. Turn the knob on both sides 90°. Make sure that
the knobs are securely fixed.
► Fig.37: 1. Knob
NOTICE:
Be careful not to pinch the cord when
folding the handle.
4. Loosen the thumb nuts on both sides, and then
fold the upper handle as shown in the figure.
► Fig.38: 1. Thumb nut 2. Upper handle
5.
Place the machine in the upright position.
NOTE: When putting the mower in the upright posi-
tion, do not hold the handle only, but hold the mower
body and handle.
6.
Store the grass basket as shown in the figure.
► Fig.39: 1. Grass basket
► Fig.40: 1. Grass basket
Removing or installing the mower
blade
WARNING:
onds after releasing the switch. Do not start any
operation until the blade comes to a complete
stop.
WARNING:
battery cartridge when removing or installing the
blade. Failure to remove the lock key and battery
cartridge may cause a serious injury.
WARNING:
dling the blade.
NOTICE:
When removing or installing the
mower blade, use the box wrench included in the
machine package.
Removing the mower blade
1. Put the mower on its side so that the mowing
height adjusting lever comes to the lower side.
2. To lock the blade, insert the pin into the hole on
the mower body as far as it will go.
3. Turn the bolt counterclockwise with box wrench 17.
► Fig.41: 1. Mower blade 2. Pin 3. Box wrench
4.
Remove the bolt, and then mower blade.
► Fig.42: 1. Blade support 2. Mower blade 3. Bolt
4. Protrusion
NOTICE:
When installing the mower blade, make
sure that the protrusions on the blade support fit
in the holes in the mower blade.
19 ENGLISH
The blade coasts for a few sec-
Always remove the lock key and
Always wear gloves when han-