1. Manuals
  2. Brands
  3. Accent Manuals
  4. Indoor Furnishing
  5. DUO II
  6. Assembly and instruction manual

Accent DUO II Assembly And Instruction Manual

Electric single desk
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
DUO II ELECTRIC
SINGLE DESK
ASSEMBLY AND
INSTRUCTION GUIDE

Advertisement

Table of Contents
loading

Related Manuals for Accent DUO II

Summary of Contents for Accent DUO II

  • Page 1 DUO II ELECTRIC SINGLE DESK ASSEMBLY AND INSTRUCTION GUIDE...
  • Page 2 TABLE OF CONTENTS Assembly Instructions User Instructions 7-13 Care and Maintenance Tools Required Battery Drill 4mm Hex Bit #2 Square Drive Bit www.accentworkspaces.co.nz...
  • Page 3 DUO II ELECTRIC SINGLE DESK A. ASSEMBLY DIAGRAM 0800 126 826 | support@accentworkspaces.co.nz...

  • Page 4: Packing List

    B. PACKING LIST HARDWARE SECTION QUANTITY Foot 2pcs Lifting Column (Motor) Upper Side Support 2pcs Steel Hanger Extendable Tube Framework 2pcs Transmission Tube Hex Bar Lifting Column ACCESSORY PACKAGE QUANTITY Screw ST6x23 15pcs Bolt M6x10 5pcs Bolt M6x16 8pcs Glide 4pcs Cable Ties 2pcs...
  • Page 5 C. HOW TO INSTALL THE DESK STEP 2 STEP M6x10 4pcs Install the lifting column, insert the screw into the keyhole of the lifting column and pull to one side, Take out the framework, release the M6x10 bolt with 4MM hex wrench. then fasten the M6x10 with a 4mm hex wrench.
  • Page 6 STEP 6 STEP M6x10 4pcs Our control box and AC adaptor are pre-fixed to the Install upper side support. bracket, hang the bracket to frame and put on desktop. STEP STEP ST6x23 14pcs Tighten Check the Transmission tube is connected to both legs.
  • Page 7 DUO II ELECTRIC SINGLE DESK USER INSTRUCTIONS SECTION PAGE Parts List Technical Specifications Directions of use Trouble Shooting Warranty Changing between CM and Inch – 1UN Setting Handset Display Brightness - 2BR Adjust Upward Sensitivity - 3FU Adjust Downward Sesitivity - 4FD...

  • Page 8: Parts List

    A. PARTS LIST HARDWARE SECTION QUANTITY Lifting Column 2pcs Handset Control Box AC Adaptor Power Cord B. TECHNICAL SPECIFICATIONS Input 110~240VAC Output Power 24VDC Load Capacity 800N Speed 20mm/s Stroke 450mm Min Install Dimension 700mm Operation Temperature 0-400C Duty Cycle Max.22% or 5min on and 18min off www.accentworkspaces.co.nz...

  • Page 9: Direction For Use

    C. DIRECTION FOR USE 1. Correctly connect the Control Box, Handset, Power Cord, Lifting Column & Patch Cord. (Picture 1). Plug the power cord into 110~220VAC outlet the LCD display will display will display current height. Reset (Initialization): Press and hold the down button, the handset will display “rES” and the desk will begin to lower, until to the lowest height then slightly rise.

  • Page 10: Warranty Notice

    4. Low Voltage protection (E08) Power Voltage is too low for the controller, this is a safety cut out protection. System will recover as soon as voltage returns to normal. 5. High Voltage protection (E09) Power Voltage is too high for the controller, this is a safety cut out protection. System will recover as soon as voltage returns to normal.
  • Page 11 H. ADJUST UPWARD SENSITIVITY-3FU 1. Keep pressing Button “M” for 3 seconds. Handset will display “S---”, then release pressing Button “M” and press Button “M” again to enter, the code “1Un” will then appear. 2. Press button “Up”/“Down” to be “3Fu”. Then press button “M” to enter, this will display current upward sensitivity level (L5).
  • Page 12 K. SWITCHING BETWEEN MODES-6HC 1. Keep pressing Button “M” for 3 seconds. Handset will display “S---”, then release pressing button “M” and press button “M” again to enter, the code “1Un” will then appear. 2. Press button “Up”/“Down” to be “6Hc”, then press button “M” to enter, this will display current mode: “001”.

  • Page 13: Handset Lock

    3. Please press “up” and “down” to select your favorite fatigue mode, then press button “M” to preserve. 4. You can press “UP” button to begin fatigue test, also you can quit the fatigue test by unplugging the power cord. O.

  • Page 14: Care And Maintenance

    FACTSHEET CARE & MAINTENANCE GENERAL CARE – INFORMATION • Avoid scourers and abrasives as they will damage the surface. • Don’t place hot objects, electrical appliances or pots straight from the oven or cooker onto your laminate surface. • Don’t cut on the laminate surface. •...
  • Page 15 Don’t hesitate to reach out to us if you have any queries or need assistance, give our SCAN TO REGISTER team a call on 0800 826 126. Thank you again for choosing Accent Group products. Best regards, The Accent Group Team...
  • Page 16 Version #011123 0800 126 826 support@accentworkspaces.co.nz 22 Hood Street Wellsford, Auckland 0900 New Zealand...

Table of Contents