Table of Contents
Advertisement
1. Load the cassette tape into Deck II.
2. Set Deck | to the stop mode.
3. Use the FUNCTION switch to set to TAPE.
4. Hold down the
REC (@) switch first and then press the
PLAY
(>) switch to start erasing.
¢ Press the STOP/EJECT switch to stop erasing at any
time.
¢ TAPE COPYING
possible.
NORMAL SPEED COPYING
e The REC indicator will flash.
NOTE:
¢ When setting the FUNCTION Switch to TAPE and listen-
ing to playback from Deck |, set the volume and graphic
equalizer controls.
7. To stop while making
a copy, press the STOP/EJECT
switches on both decks.
HIGH SPEED COPYING
1. Perform the preliminary operations on page
10.
2. Press the STOP/EJECT switch; then load the original cas-
sette tape into Deck | and the cassette tape to be used for
recording into Deck II. Close the casette doors.
3. Press the SYNCHRO switch of the COPY MODE switches.
¢ The SYNCHRO
indicator will light.
* Tape copying is possible regardless of the FUNCTION
switch setting; however, the sound from the speakers
will be that of the selected program source.
4. Press
the HIGH
SPEED
switch
of the COPY
MODE
switches.
¢ The HIGH SPEED indicator will light.
5. Hold down the REC (@) switch and then press the PLAY
(>) switch of Deck Il.
¢ The REC indicator will flash.
¢ The tape will remain stopped.
NOTE:
Make sure that both the
SYNCHRO and HIGH SPEED indicators
are lit. High speed copying is not possible unless both are lit so
press the
STOP/EJECT
switch, return to item 3 and repeat the
operation.
6. Press the PLAY (>) switch of Deck |.
¢ The REC indicator will light.
¢ The SYNCHRO and HIGH SPEED indicators will flash (it
will continue to flash when PAUSE is used with the re-
mote control).
7. To stop while making a copy, press the STOP/EJECT
switches on both decks.
NOTE:
©
When using in the same roomas a television set, position for
enough away from the set to avoid interference, or turn off
power to the television set.
©
Beat may occur and be included in recordings when copying .
while receiving AM broadcasts. In such cases, set the BEAT
CUT switch
on the rear panel to the side where beat is less.
There is no need to operate the BEAT CUT switch except for
AM broadcasts.
When Deck | is stopped while copying, restart from step 6.
When Deck II is stopped, restart from the beginning.
NOTE:
Pressing Pause from the remote control, operating the Deck |
switches {except PLAY switch) cancels the Deck If pause mode
and enters the
SYNCHRO REC STANDBY mode. Playing Deck
lin this status restarts SYNCHRO REC.
13
RX-1180, RX-1190
UNATTENDED RECORDING (Deck II only)
1.
ah
Wh
NO
Set the POWER switch to the standby position and con-
nect the power cord to the outlet on the audio timer.
. Set the POWER
switch to ON.
. Load a tape for recording in the Deck Il.
. Select the DOLBY NR switch.
. Press the TUNER FUNCTION switch and tune in the sta-
tion to be recorded.
. Turn down the volume control to minimum position.
. Set the audio timer so that the power comes on at the
desired time. (Power to the components should be off at
this point.)
. Hold down the REC (@) switch and then press the PLAY
(>) switch of Deck I.
. Power will be turned on automatically at the preset time,
and recording will start.
WAKE-UP PLAYBACK (Deck I and Il)
1.
oR
WN
oO
. Set the POWER switch to ON.
. Select the DOLBY NR switch.
. Load the tape which is to be played back.
required when timer playback starts.
. Press the PLAY (C>) switch.
MIXING KNOW-HOW
Mixing involves combining the signals from two input sources
(a microphone and a tape, for example)
SINGING ALONG
WITH A PROGRAM
SOURCE
Operate after setting the MIXING LEVEL control tominimum.
BWN
>
an
oD
©
. Perform the preliminary operations on page
1¢.
. Plug a microphone into the MIC jack.
. Adjust the volume to a suitable level.
. Set the MIXING LEVEL control to the center position.
¢ If howling occurs (a high-pitched sound fromthe speak-
ers), take the following steps.
(1) Move the microphone away from the speakers.
(2) Lower the volume.
. Select the desired program source using the FUNCTION
switches.
. Start playback of the program source.
. Adjust the overall volume.
. Using the MIXING LEVEL control, adjust the sound balance
between the microphone and the program souce.
. Sing along with the program using the microphone.
NOTE:
Recording of mixed sound is not possible.
When not using the MIXING function, be sure to se the MIX-
ING LEVEL control to SOURCE and remove the mcrophone
plug from the MIC jack.
14
Advertisement
Table of Contents
