Black & Decker BHSMP2008 Original Instructions Manual page 11

Attaching the water tank
Slide the water tank (3) down using the ribs to locate
u
into the main unit (2), ensure that the water tank is firmly
seated to create a seal.
Switching on and off (Fig. E)
To switch the appliance on, press the ON/Off switch (1).
u
The white light (1c) will illuminate when the power is
on and the boiler is heating up. The green light (1b) will
illuminate when the boiler is up to temperature the user
must press the trigger on the steam handle (11b) to create
steam.
To switch the appliance off, press the ON/Off switch (1).
u
Caution! Never leave the steam mop in one spot on any
surface for any period of time.
Always place the steam mop supported in the upright position
when stationary and make sure the steam mop is turned off
when not in use.
Caution! Always empty the water tank after use.
Note! when first filled or after running dry, it can take up to 180
seconds for steam to be produced
Floor Worktop Surface
Wood/Laminate
Tile/Vinyl
Stone/Marble
Accessories
Grout Brush
Small Brush
Small Brush with copper bristles
Window / garment Squeegee
Wall paper atachment
Note: Always check you are using the correct setting of steam
before using your steam mop.
Steam user interface
This steam mop is fitted with a Steam user interface panel
which shows 3 indicator lights (1a, 1b and 1c). They are used
to select the correct operating mode for your particular cleaning
operation.
Turn unit on by pressing the On/Off switch (1).
u
White indicator light (1c) is illuminated when powered on
u
and boiler is heating up.
Green indicator light (1b) is illuminated when the unit is up
u
to temperature and ready to use.
User must slide the lock off button (11a) on the steam
u
handle (11) from the locked position.
Press the trigger (11b) on the steam handle (11) to create
u
steam.
After use always slide the lock off button (11a) on the
u
steam handle (11) back to the locked position.
Setting
Min/Low Steam setting
Mid Steam setting
Max/High Steam setting
Setting
Max/High Steam setting
Max/High Steam setting
Max/High Steam setting
Min/Low Steam setting
Max/High Steam setting
(Original instructions)
The left indicator light (1a) is illuminated when the water
u
tank (3) is empty, take out the water tank (3) and fill with
water.
To switch appliance off, press the on/off switch (1).
u
Note: Always check you are using the correct setting before
using your steam mop.
Attaching accessories to the steam handle
Warning! Inspect the seal between the connection point on
the steam handle and the accessories before
each use. If the seal malfunctions or is damaged, please
contact your nearest authorised repair agent.
Do not use the appliance.
Warning! The unit should be switched off before accessories
are fitted.
Attaching large accessories (Fig. F)
Accessories 7,8 and 9 can be attached directly to the end
u
of the steam handle.
Align the accessory and push firmly onto the steam
u
handle.
Make sure latching feature is locked into position to create
u
a seal
Important! All accessories must be attached to the steam
handle (11) for use.
Removing a large accessory
Press latch and pull accessory away from the steam
u
handle (11).
Warning! Allow the unit and all accessories to cool before
attempting to remove.
Attaching small brush accessories
Attach steam concentrator (8) to the steam nozzle
u
Small accesories 10,15,16 can be pushed directly onto
u
the steam concentrator (8).
Make sure the small accessory is pushed on to create a
u
seal and stays in position.
Removing a small accessory 10,15,16
Pull accesory away from the steam concentrator (8).
u
Warning! Allow the unit and all accessories to cool before
attempting to remove.
Fitting the squeegee onto the hand nozzle 12,
9 (Fig. I, J, K, L)
Fit the squeegee rear hooks (20) into the handle nozzle's
u
latches (18) as shown in figure K.
Push the handle nozzle down until the body is locked by
u
front peg of the squeegee (19) as shown in figure L.
ENGLISH
11