Specifications; Additional Safety Rules - Makita HR3850B Instruction Manual

ENGLISH
1 Side grip
2 Grip base
3 Red dot (Tool holder)
4 Red dot (Tool retainer)
5 Tool retainer
6 Press in
7 Turn 180°
8 Change lever

SPECIFICATIONS

Model
Capacities
Tungsten-carbide bit ....................................................................... 35 mm
Core bit ........................................................................................... 79 mm
–1
No load speed (min ) ....................................................................... 440
Blows per min. ................................................................................... 3,300
Overall length .................................................................................... 400 mm
Net weight .......................................................................................... 5.8 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can be operated on single-phase AC/DC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed
Safety instructions.

ADDITIONAL SAFETY RULES

1. Wear a hard hat (safety helmet), safety glasses
and/or face shield. It is also highly recom-
mended that you wear a dust mask, ear pro-
tectors and thickly padded gloves.
2. Be sure the bit is secured in place before
operation.
3. Under normal operation, the tool is designed
to produce vibration. The screws can come
loose easily, causing a breakdown or accident.
Check tightness of screws carefully before
operation.
4. In cold weather or when the tool has not been
used for a long time, let the tool warm up for
several minutes by operating it under no load.
This will loosen up the lubrication. Without
proper warm-up, hammering operation is dif-
ficult.
Explanation of general view
9 For rotation with hammering
10 For hammering only
11 Wing bolt
12 Depth gauge
13 Switch trigger
14 Core bit
15 Adapter
16 Center bit
5. Always be sure you have a firm footing.
6. Hold the tool firmly with both hands.
7. Keep hands away from moving parts.
8. Do not leave the tool running. Operate the tool
9. Do not point the tool at any one in the area
10. When drilling or chipping into walls, floors or
11. Do not touch the bit or parts close to the bit
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Side grip (auxiliary handle) (Fig. 1 & 2)
For maximum control and safer operation, always use
the side grip with this tool. The side grip swings
around to either side, allowing easy handling of the
tool in any position. Loosen the side grip by turning it
counterclockwise, swing it to the desired position and
then tighten it by turning clockwise. (Fig. 1)
The side grip can also be installed in the position
shown in Fig. 2. Remove the side grip from the grip
base by turning the side grip counterclockwise. Screw
the side grip on either side of the tool, whichever is
convenient.
17 Rod
18 Hex wrench
19 Rear cover
20 Screwdriver
21 Brush holder cap
22 Lock nut wrench
23 Crank cap
24 Hammer grease
HR3520B
Be sure no one is below when using the tool in
high locations.
only when hand-held.
when operating. The bit could fly out and
injure someone seriously.
wherever "live" electrical wires may be
encountered, DO NOT TOUCH ANY METAL
PARTS OF THE TOOL!
Hold the tool by the insulated grasping sur-
faces to prevent electric shock if you drill or
chip into a "live" wire.
immediately after operation; they may be
extremely hot and could burn your skin.
HR3850B HR3850K
38 mm 38 mm
118 mm 118 mm
240 240
2,900 2,900
442 mm 455 mm
7.5 kg 7.5 kg
5