Related Manuals for Siemens SIMATIC NET RUGGEDCOM RS900F
Summary of Contents for Siemens SIMATIC NET RUGGEDCOM RS900F
- Page 1 All manuals and user guides at all-guides.com Installation Manual SIMATIC NET Rugged Ethernet Switches RUGGEDCOM RS900F Edition 02/2020 https://www.siemens.com...
- Page 2 All manuals and user guides at all-guides.com Preface Introduction Installing the Device SIMATIC NET Device Management Rugged Ethernet Switches RUGGEDCOM RS900F Communication Ports Technical Specifications Installation Manual Certification 02/2020 C79000-G8976-1350-04...
- Page 3 Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommend- ed or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
- Page 4 Accessing Documentation ....................... v Disclaimer of Liability ......................v Registered Trademarks ......................v Training ..........................vi Customer Support ........................vi Contacting Siemens ....................... vii Introduction ........................... 1 Feature Highlights ....................1 Description ......................2 Required Tools and Materials ................. 3 Decommissioning and Disposal ................
- Page 5 All manuals and user guides at all-guides.com Table of Contents Failsafe Alarm Relay Specifications ..............26 Supported Networking Standards ................ 26 Copper Ethernet Port Specifications ..............26 Fiber Optic Ethernet Port Specifications ............... 27 Operating Environment ..................27 Mechanical Specifications ..................27 Dimension Drawings ...................
- Page 6 However, deviations between the product and the documentation may exist. Siemens shall not be liable for any errors or omissions contained herein or for conse- quential damages in connection with the furnishing, performance, or use of this ma- terial.
- Page 7 Siemens Sales representative. Customer Support Customer support is available 24 hours, 7 days a week for all Siemens customers. For technical support or general information, contact Siemens Customer Support through any of the following methods: Online Visit http://www.siemens.com/automation/support-request...
- Page 8 All manuals and user guides at all-guides.com Preface Contacting Siemens Contacting Siemens Address Siemens AG Industry Sector 300 Applewood Crescent Concord, Ontario Canada, L4K 5C7 Telephone Toll-free: 1 888 264 0006 Tel: +1 905 856 5288 Fax: +1 905 856 1995 E-Mail ruggedcom.info.i-ia@siemens.com...
- Page 9 All manuals and user guides at all-guides.com Preface Contacting Siemens viii RUGGEDCOM RS900F Installation Manual, 02/2020, C79000-G8976-1350-04...
- Page 10 All manuals and user guides at all-guides.com Introduction The RUGGEDCOM RS900F is a 9-port utility-grade, fully managed Ethernet switch specifically designed to operate reliably in electrically harsh and climatically demand- ing environments. The RUGGEDCOM RS900F provides a high level of immunity to electromagnetic in- terference and heavy electrical surges typical of environments found on plant floors and curb-side traffic control cabinets.
- Page 11 All manuals and user guides at all-guides.com Introduction 1.2 Description • 20 AWG Galvanized Steel • DIN or panel mounting options provide secure mechanical reliability • [Optional] Conformal coated printed circuit boards Universal Power Supply Options • Fully integrated power supply •...
- Page 12 All manuals and user guides at all-guides.com Introduction 1.3 Required Tools and Materials Power Supply Terminal Block Figure 1.1 RUGGEDCOM RS900F POWER LED Illuminates green when power is supplied to the device. ALARM LED Illuminates red when an alarm condition exists. Console Port The serial console port is for interfacing directly with the device and accessing initial management functions.
- Page 13 Siemens also does not recommend using copper Ethernet ports to interface with de- vices in the field across distances that could produce high levels of ground potential rise (i.e.
- Page 14 NOTICE Worn, damaged or missing seals must be replaced immediately. Replacement seals are available for purchase from Siemens. For more information, contact a Siemens Sales representative. There are three ways to determine if a security seal has been tampered with: •...
- Page 15 All manuals and user guides at all-guides.com Introduction 1.6 Tamper-Evident Security Seals RUGGEDCOM RS900F Installation Manual, 02/2020, C79000-G8976-1350-04...
- Page 16 This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void. Changes or modifications not expressly approved by Siemens AG could invalidate specifications, test results, and agency approvals, and void the user's authority to operate the equipment.
- Page 17 2.2 Installing the Device in Hazardous Locations Verify all items are included. NOTICE If any item is missing or damaged, contact Siemens for assistance. Installing the Device in Hazardous Locations The RUGGEDCOM RS900F is designed to comply with the safety standards for Class I, Division 2, Zone 2 hazardous locations where concentrations of flammable gases, va- pors or liquids may be present, as opposed to normal operating environments.
- Page 18 All manuals and user guides at all-guides.com Installing the Device 2.3 Mounting the Device Sample Hazardous Location Label The following is an example of the RUGGEDCOM RS900F hazardous location label: Figure 2.1 Compliance Label (Example) Mounting the Device The RUGGEDCOM RS900F is designed for maximum mounting and display flexibility. It can be equipped with adapters that allow it to be attached to a DIN rail or panel.
- Page 19 All manuals and user guides at all-guides.com Installing the Device 2.3.1 Mounting the Device on a DIN Rail Mounting the Device To mount the device to a DIN rail, do the following: Hook the top teeth of the adapter onto the DIN rail. Note The adapter features a sliding release with a slot at the bottom for a flathead screwdriver.
- Page 20 All manuals and user guides at all-guides.com Installing the Device 2.3.2 Mounting the Device to a Panel Removing the Device To remove the device from a DIN rail, do the following: Insert a flathead screwdriver into the slot of the sliding release and move it down.
- Page 21 All manuals and user guides at all-guides.com Installing the Device 2.4 Connecting the Failsafe Alarm Relay Place the device against the panel and align the adapters with the mounting holes. Screw Panel Mount Adapter Figure 2.4 Panel Mounting Secure the adapters to the panel with #6-32 screws. Connecting the Failsafe Alarm Relay The failsafe relay can be configured to latch based on alarm conditions.
- Page 22 All manuals and user guides at all-guides.com Installing the Device 2.5 Connecting Power Connect a failsafe device to the terminal block. Normally Closed Common Normally Open Figure 2.5 Failsafe Alarm Relay Wiring Connecting Power The RUGGEDCOM RS900F supports power input from a single high AC/DC or low DC power supply.
- Page 23 All manuals and user guides at all-guides.com Installing the Device 2.5.1 Connecting High AC/DC Power 2.5.1 Connecting High AC/DC Power To connect a high AC/DC power supply to the device, do the following: NOTICE Electrical hazard – risk of damage to equipment Do not connect AC power cables to terminals for DC power.
- Page 24 All manuals and user guides at all-guides.com Installing the Device 2.5.1 Connecting High AC/DC Power Connect the positive wire from the power source to the positive/live (+/L) termi- nal on the terminal block. Positive/Live (+/L) Terminal Negative/Neutral (-/N) Terminal Surge Ground Terminal Braided Ground Cable Figure 2.6 Terminal Block Wiring...
- Page 25 All manuals and user guides at all-guides.com Installing the Device 2.5.2 Connecting Low DC Power ± ± ± ± Positive Terminal Negative Terminal Surge Ground Terminal Braided Ground Cable Figure 2.7 Terminal Block Wiring – Dual DC Power Supply Inputs Connect the negative wire from the power source to the negative/neutral (-/N) terminal on the terminal block.
- Page 26 All manuals and user guides at all-guides.com Installing the Device 2.5.2 Connecting Low DC Power Connect the positive wire from the power source to the positive terminal on the terminal block. ± ± Positive Terminal Negative Terminal Surge Ground Terminal Braided Ground Cable Figure 2.8 Terminal Block Wiring –...
- Page 27 All manuals and user guides at all-guides.com Installing the Device 2.5.2 Connecting Low DC Power [Optional] If a redundant connection is required, repeat Step 2 Step 3 connect the secondary power inputs. ± ± ± ± Positive Terminal Negative Terminal Surge Ground Terminal Braided Ground Cable Figure 2.9 Terminal Block Wiring –...
- Page 28 All manuals and user guides at all-guides.com Device Management This section describes how to connect to and manage the device. Connecting to the Device The following describes the various methods for accessing the RUGGEDCOM RS900F console and Web interfaces on the device. For more detailed instructions, refer to the RUGGEDCOM RS900F User Guide for the RUGGEDCOM RS900F.
- Page 29 All manuals and user guides at all-guides.com Device Management 3.2 Configuring the Device The serial console port implements RS232 DCE (Data Communication Equipment) on a DB9 connector. The following is the pin-out for the port: Name Description Reserved (Do Not Connect) Transmit Data Receive Data Reserved (Do Not Connect)
- Page 30 All manuals and user guides at all-guides.com Communication Ports The RUGGEDCOM RS900F can be equipped with various types of communication ports to enhance its abilities and performance. Ports 1 to 6 Ports 7 and 8 Port 9 Figure 4.1 Port Assignment Port Type 1 to 6...
- Page 31 All manuals and user guides at all-guides.com Communication Ports 4.1 Copper Ethernet Ports WARNING Electric shock hazard – risk of serious personal injury and/or equipment inter- ference When shielded cables are used, make sure the shielded cables do not form a ground loop via the shield wire and the RJ45 receptacles at either end.
- Page 32 All manuals and user guides at all-guides.com Communication Ports 4.2 Fiber Optic Ethernet Ports Fiber Optic Ethernet Ports Fiber optic Ethernet ports are available with either MTRJ (Mechanical Transfer Reg- istered Jack), LC (Lucent Connector), SC (Standard or Subscriber Connector) or ST (Straight Tip) connectors.
- Page 33 All manuals and user guides at all-guides.com Communication Ports 4.2 Fiber Optic Ethernet Ports RUGGEDCOM RS900F Installation Manual, 02/2020, C79000-G8976-1350-04...
- Page 34 All manuals and user guides at all-guides.com Technical Specifications This section provides important technical specifications related to the device. Power Supply Specifications Note When determining cable lengths, make sure the minimum input voltage for the pow- er supply is provided at the power source. Hazardous Environments Power Sup- Input Range...
- Page 35 All manuals and user guides at all-guides.com Technical Specifications 5.2 Failsafe Alarm Relay Specifications Failsafe Alarm Relay Specifications Hazardous Environments Maximum Switching Voltage Rated Switching Current Isolation 30 VDC 1500 V for 1 minute 80 VDC 0.3 A 30 VAC Non-Hazardous Environment Maximum Switching Voltage Rated Switch- Isolation...
- Page 36 3 dBm. To convert from peak to average, subtract 3 dBm. • Maximum segment length is greatly dependent on factors such as fiber quality, and the number of patches and splices. Consult a Siemens sales associate when determining maximum segment distances. Operating Environment The RUGGEDCOM RS900F is rated to operate under the following environmental con- ditions.
- Page 37 All manuals and user guides at all-guides.com Technical Specifications 5.8 Dimension Drawings Dimension Drawings Note All dimensions are in millimeters, unless otherwise stated. 65.3 116.59 7.87 Figure 5.1 Overall Dimensions RUGGEDCOM RS900F Installation Manual, 02/2020, C79000-G8976-1350-04...
- Page 38 All manuals and user guides at all-guides.com Technical Specifications 5.8 Dimension Drawings 130.2 13.64 101.6 11.2 78.74 120.65 Figure 5.2 Panel and DIN Rail Mount Dimensions RUGGEDCOM RS900F Installation Manual, 02/2020, C79000-G8976-1350-04...
- Page 39 All manuals and user guides at all-guides.com Technical Specifications 5.8 Dimension Drawings RUGGEDCOM RS900F Installation Manual, 02/2020, C79000-G8976-1350-04...
- Page 40 All manuals and user guides at all-guides.com Certification The RUGGEDCOM RS900F device has been thoroughly tested to guarantee its confor- mance with recognized standards and has received approval from recognized regula- tory agencies. Approvals This section details the standards to which the RUGGEDCOM RS900F complies. 6.1.1 This device meets the requirements of the following Canadian Standards Association (CSA) standards under certificate 16.70065161:...
- Page 41 Explosive Atmospheres – Part 15: Equipment Protection by Type of Protection "n" 6.1.3 European Union (EU) This device is declared by Siemens AG to comply with essential requirements and other relevant provisions of the following EU directives: • EN 60950-1 Information Technology Equipment –...
- Page 42 Methods of Measurement The device is marked with a CE marking and can be used throughout the European community. A copy of the CE Declaration of Conformity is available from Siemens AG. For contact information, refer to "Contacting Siemens (Page vii)".
- Page 43 Information Technology Equipment – Safety – Part 1: General Requirements 6.1.8 RoHS This device is declared by Siemens AG to meet the requirements of the following Ro- HS (Restriction of Hazardous Substances) directives for the restricted use of certain hazardous substances in electrical and electronic equipment: •...
- Page 44 All manuals and user guides at all-guides.com Certification 6.2 EMC and Environmental Type Tests IEC 61000-6-2 • Electromagnetic Compatibility (EMC) – Part 6-2: Generic Standards – Immunity for Industrial Environments • IEC 61850-3 Communication Networks and Systems in Substations – Part 3: General Require- ments •...
- Page 45 All manuals and user guides at all-guides.com Certification 6.2 EMC and Environmental Type Tests Test Description Test Levels Severi- ty Levels Magnetic Field Enclo- 40 A/m Continuous 61000-4-8 sure Ports 1000 A/m for 1 s Voltage Dips and Interrupts AC Pow- 100% for 5 Periods ...
- Page 46 All manuals and user guides at all-guides.com Certification 6.2 EMC and Environmental Type Tests Description Test Levels Enclosure Contact ± 8 kV Enclosure Air ± 15 kV Radiated RFI Enclosure Ports 35 V/m Fast Transient Signal Ports ± 4 kV @ 2.5 kHz DC Power Ports ±...
- Page 47 All manuals and user guides at all-guides.com Certification 6.2 EMC and Environmental Type Tests RUGGEDCOM RS900F Installation Manual, 02/2020, C79000-G8976-1350-04...
- Page 48 All manuals and user guides at all-guides.com Further Information Siemens RUGGEDCOM https://www.siemens.com/ruggedcom Industry Online Support (service and support) https://support.industry.siemens.com Industry Mall https://mall.industry.siemens.com Siemens AG Digital Industry Process Automation Postfach 48 48 90026 NÜRNBERG GERMANY...